سلام به همگی.
حاجی این درایور مودم من نسب نمیشه.
اینترنت زیرو رو کردم و علاوه بر اینکه درایور مربوط به چیپست HSF و کرنل 2.6.22_14_generic رو نصب کردم و جواب نداد!!!! هر درایوری که مربوط به HSF بودش رو dl کردم ولی هیچ کدوم جواب ندادن.
خروجی ModemData.txt بعد اسکن ScanModem به این صورت:
-------------------------- System information ----------------------------
CPU=i686,
Linux version 2.6.22-14-generic (buildd@palmer) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP Sun Oct 14 23:05:12 GMT 2007
scanModem update of: 2009_07_17
There are no blacklisted modem drivers in /etc/modprobe* files
Potentially useful modem drivers now loaded are:
Attached USB devices are:
ID 0bda:0151 Realtek Semiconductor Corp.
If a cellphone is not detected, see http://ubuntuforums.org/archive/index.php/t-878554.html
A sample report is: http://linmodems.technion.ac.il/bigarch/archive-nineth/msg00578.html
If a USB modem or cellphone is attached and was not detected, please
provide available information in your request to discuss@linmodems.org
For candidate card in slot 02:02.0, firmware information and bootup diagnostics are:
PCI slot PCI ID SubsystemID Name
---------- --------- --------- --------------
02:02.0 14f1:2f30 14f1:2075 Communication controller: Conexant HSF 56k Data/Fax Modem
Modem interrupt assignment and sharing:
15: 0 IO-APIC-edge libata
--- Bootup diagnostics for card in PCI slot 02:02.0 ----
=== Finished firmware and bootup diagnostics, next deducing cogent software. ===
Predictive diagnostics for card in bus 02:02.0:
Modem chipset detected on
NAME="Communication controller: Conexant HSF 56k Data/Fax Modem "
CLASS=0780
PCIDEV=14f1:2f30
SUBSYS=14f1:2075
IRQ=5
IDENT=hsfmodem
Driver=hsfmodem-drivers
For candidate modem in: 02:02.0
0780 Communication controller: Conexant HSF 56k Data/Fax Modem
Primary device ID: 14f1:2f30
Support type needed or chipset: hsfmodem
For owners of a Dell PCs with Conexant HSF modems, a driver source package with full speed enabled is available, but requires driver compiling. Read DOCs/Conexant.txt
From http://www.linuxant.com/drivers/hsf/full/downloads-ubuntu-x86.php
download hsfmodem-7.80.02.02full_k2.6.22_14_generic_ubuntu_i386.deb.zip
Under Linux unpack with:
$ unzip hsfmodem*.zip
Then install with:
$ sudo dpkg -i hsfmodem*.deb
Subsequently, the modem should be found with
$ sudo wvdialconf /etc/wvdial.conf
Edit in your personal information with:
$ sudo gedit /etc/wvdial.conf
and try dialing out with:
$ sudo wvdial.
See DOCs/Testing.txt for details.
The directions following below need only be pursued, if the above procedures are not adequate.
Start at http://www.linuxant.com/drivers/hsf/downloads-license.php to find the
hsfmodem package matching your System. For several Linux distros, there are
precompiled drivers matched to specific kernels. These have within the FileName,
your KernelVersion: 2.6.22_14_generic
They can be found through http://www.linuxant.com/drivers/hsf/full/downloads.php
A more precise location may be given a few paragraphs below.
If an EXACT Match with your your KernelVersion is not found, one of the
"Generic packages with source" near the bottom of the page must be used.
Downloaded packages must be moved into the Linux partition (home folder is OK)
and unzipped with:
unzip hsf*.zip
The installation command for a .deb suffic packages is, with root/adm permission:
sudo dpkg -i hsf*.deb
while for .rpm suffix it is, with:
rpm -i hsf*.rpm
Read DOCs/Conexant.txt
Writing DOCs/Conexant.txt
Completed candidate modem analyses.
The base of the UDEV device file system is: /dev/.udev
/dev/.udev.log
Versions adequately match for the compiler installed: 4.1.3
and the compiler used in kernel assembly: 4.1.3
The patch utility is needed and is needed for compiling ALSA drivers, and possibly others.
Minimal compiling resources appear complete:
make utility - /usr/bin/make
Compiler version 4.1
linuc_headers base folder /lib/modules/2.6.22-14-generic/build
However some compilations and executable functions may need additional files,
in the FileNames.h (so called kernel "h"eaders) collection installed in /usr/include/ .
For martian_modem, additional required packages are needed. The also required headers of package libc6 are commonly installed by default.
Compiling hsfmodem drivers does require linux-libc-dev and libc6-dev packages, for kernels 2.6.24 and later versions.
In not included on your install CD, search for them at http://packages.ubuntu.com
or comparable Repository for other Linux distros.
When compiling ALSA drivers, the utility "patch" will also be needed.
If a driver compilation fails, with message including some lack of some FileName.h (stdio.h for example), then
Some additional kernel-header files need installation to /usr/include. The minimal additional packages are libc6-dev
and any of its dependents, under Ubuntu linux-libc-dev
If an alternate ethernet connection is available,
$ apt-get update
$ apt-get -s install linux-kernel-devel
will install needed packages.
For Debian/Ubuntu related distributions, run the following command to display the needed package list:
Otherwise packages have to be found through http://packages.ubuntu.com
Once downloaded and transferred into a Linux partition,
they can be installed alltogether with:
$ sudo dpkg -i *.deb
Checking pppd properties:
-rwsr-xr-- 1 root dip 269256 2007-10-04 23:27 /usr/sbin/pppd
In case of an "error 17" "serial loopback" problem, see:
http://linmodems.technion.ac.il/linmodems/archive-sixth/msg02637.html
To enable dialout without Root permission do:
$ su - root (not for Ubuntu)
sudo chmod a+x /usr/sbin/pppd
or under Ubuntu related Linuxes
sudo chmod a+x /usr/sbin/pppd
Checking settings of: /etc/ppp/options
asyncmap 0
noauth
crtscts
lock
hide-password
modem
proxyarp
lcp-echo-interval 30
lcp-echo-failure 4
noipx
In case of a message like:
Warning: Could not modify /etc/ppp/pap-secrets: Permission denied
see http://linmodems.technion.ac.il/bigarch/archive-sixth/msg04656.html
Read Modem/DOCs/YourSystem.txt concerning other COMM channels: eth0
Which can interfere with Browser naviagation.
Don't worry about the following, it is for experts should trouble shooting be necessary.
==========================================================
Checking for modem support lines:
--------------------------------------
/device/modem symbolic link:
slmodemd created symbolic link /dev/ttySL0:
Within /etc/udev/ files:
Within /etc/modprobe.conf files:
/etc/modprobe.d/blacklist-modem:# Uncomment these entries in order to blacklist unwanted modem drivers
/etc/modprobe.d/blacklist-modem:# blacklist snd-atiixp-modem
/etc/modprobe.d/blacklist-modem:# blacklist snd-via82xx-modem
/etc/modprobe.d/alsa-base:options snd-atiixp-modem index=-2
/etc/modprobe.d/alsa-base:options snd-via82xx-modem index=-2
Within any ancient /etc/devfs files:
Within ancient kernel 2.4.n /etc/module.conf files:
--------- end modem support lines --------
درایوری دانلود کردم و نصبش کردم اینه: http://www.linuxant.com/drivers/hsf/full/archive/hsfmodem-7.80.02.04full/hsfmodem_7.80.02.04full_k2.6.22_14_generic_ubuntu_i386.deb.zip
ولی جواب نداد . منظورم انه که نتنها بعد از اجرا ی wvdial ارور داد، بلکه حتی موقع نصب آن هم عباراتی مثل sorry و از این چیزا میده
نکته ای که هست ScanModem اسم درایور رو hsfmodem-7.80.02.02full_k2.6.22_14_generic_ubuntu_i386.deb.zip معرفی کرده ولی تو لینکی که داده این نیستش. واسه همین من بالایی رو dl کردم.
خلاصه دیگه قهوه ای شدم تو این راه.
یکی لطف کنه و به دادمون برسه.
سلام احمد.
خیلی لطف کردی که به این سرعت جوابمو دادی.
دمت گرم.
من این درایور رو نصب کردم خیلی ok نصب شد :)
کارایی هم که گفته بودی رو انجام دادم .
یه connection با pppconfig درست کردم.
ولی قسمت port بود فکر کنم که مال خودش اگه اشتباه نکنم یه چیز تو این مایه ها بودش: dev/tty/ کار نکرد و من اون رو با توجه به خط
The /dev/modem alias (symlink) points to ttySHSF0
که آخرین سطری بود که بعد از نصب driver اومدش به جای tty ، نوشتم ttyshsf0 .
که modem شرو کرد به شماره گیری با دستور pon connection_name ولی به اینترنت کانکت نشد. هیچ error ی هم نداد.
رفتم و wvdial رو config کردم اینم شروع کرد به شماره گیری ولی کانکت نشد این error رو داد:
linux@linux:~$ wvdial
WvDial<*1>: WvDial: Internet dialer version 1.56
WvModem<*1>: Cannot set information for serial port.
WvDial<*1>: Initializing modem.
WvDial<*1>: Sending: ATZ
WvDial Modem<*1>: ATZ
WvDial Modem<*1>: OK
WvDial<*1>: Modem initialized.
WvDial<*1>: Sending: ATDT9712200
WvDial<*1>: Waiting for carrier.
WvDial Modem<*1>: ATDT9712200
WvDial Modem<*1>: CONNECT 115200
WvDial Modem<*1>: User Access Verification
WvDial Modem<*1>: Username:
WvDial<*1>: Carrier detected. Starting PPP immediately.
WvDial<Notice>: Starting pppd at Thu Jul 30 17:20:07 2009
WvDial<Err>: Warning: Could not modify /etc/ppp/pap-secrets: Permission denied
WvDial<Err>: --> PAP (Password Authentication Protocol) may be flaky.
WvDial<Err>: Warning: Could not modify /etc/ppp/chap-secrets: Permission denied
WvDial<Err>: --> CHAP (Challenge Handshake) may be flaky.
WvDial<Notice>: Pid of pppd: 10001
WvDial<*1>: Using interface ppp0
WvDial<*1>: Disconnecting at Thu Jul 30 17:20:09 2009
WvDial<*1>: The PPP daemon has died: Authentication error.
WvDial<*1>: We failed to authenticate ourselves to the peer.
WvDial<*1>: Maybe bad account or password? (exit code = 19)
WvDial<*1>: man pppd explains pppd error codes in more detail.
WvDial<Notice>: I guess that's it for now, exiting
WvDial<Notice>: The PPP daemon has died. (exit code = 19)
وقتی شماره ی خودم رو به جای شماره ی تماس نوشتم درست کار کرد که نشون می ده خود مودم ok هستش.
user&pass کارت اینترنت رو چند بار تست کردم درسته.
اینم مال وقتی هستش که داشتم درایور رو نصب می کردم:
linux@linux:~/Desktop$ sudo dpkg -i hsfmodem_7.60.00.18oem_i386.deb
[sudo] password for linux:
dpkg - warning: downgrading hsfmodem from 7.80.02.04full-k2.6.22-14-generic-1.ubuntu to 7.60.00.18oem.
(Reading database ... 93161 files and directories currently installed.)
Preparing to replace hsfmodem 7.80.02.04full-k2.6.22-14-generic-1.ubuntu (using hsfmodem_7.60.00.18oem_i386.deb) ...
Unpacking replacement hsfmodem ...
Setting up hsfmodem (7.60.00.18oem) ...
Conexant HSF softmodem driver, version 7.60.00.18oem
If you need assistance or more information, please go to:
http://www.linuxant.com/
When reporting a problem for the first time, please send
us the file generated by "hsfconfig --dumpdiag".
No pre-built modules for: Ubuntu-7.10 linux-2.6.22-14-generic i686-SMP
Trying to automatically build the driver modules...
(this requires a C compiler and proper kernel sources to be installed)
Building modules for kernel 2.6.22-14-generic, using source directory
/lib/modules/2.6.22-14-generic/build. Please wait...
done.
Unable to determine region, defaulting to "USA"
Setting region for modem unit 0: "USA"
To change, use "hsfconfig --region" or "AT+GCI=<T35code>"
The current region can be displayed by entering "ATI9" in a terminal program.
Note: HDA support not compiled in the driver (requires a 2.6.16 or later kernel)
Note: kernel module snd-via82xx-modem overridden by hsfmc97via
Note: kernel module snd-intel8x0m overridden by hsfmc97ich hsfmc97sis
Note: kernel module snd-atiixp-modem overridden by hsfmc97ati
Current parameters: ("hsfconfig --info")
Config for modem unit 0: /dev/ttySHSF0
Device instance: 0-PCI-14f1:2f30-14f1:2075
HW revision : Basic2 2.18 Standard DAA 3VoltsIA
HW profile name: hsfpcibasic2hsfi
Current region : USA (T.35 code: 00B5)
The /dev/modem alias (symlink) points to ttySHSF0
linux@linux:~/Desktop$ sudo hsfconfig
Conexant HSF softmodem driver, version 7.60.00.18oem
If you need assistance or more information, please go to:
http://www.linuxant.com/
When reporting a problem for the first time, please send
us the file generated by "hsfconfig --dumpdiag".
Warning: existing driver modules found under:
/lib/modules/2.6.22-14-generic/
Would you like to keep using them? [no]
No pre-built modules for: Ubuntu-7.10 linux-2.6.22-14-generic i686-SMP
Trying to automatically build the driver modules...
(this requires a C compiler and proper kernel sources to be installed)
Where is the linux source build directory that matches your running kernel?
[/lib/modules/2.6.22-14-generic/build]
Building modules for kernel 2.6.22-14-generic, using source directory
/lib/modules/2.6.22-14-generic/build. Please wait...
done.
Please enter region name for modem unit 0 [USA]: iran
Setting region for modem unit 0: "IRAN*"
To change, use "hsfconfig --region" or "AT+GCI=<T35code>"
The current region can be displayed by entering "ATI9" in a terminal program.
Note: HDA support not compiled in the driver (requires a 2.6.16 or later kernel)
Note: kernel module snd-via82xx-modem overridden by hsfmc97via
Note: kernel module snd-intel8x0m overridden by hsfmc97ich hsfmc97sis
Note: kernel module snd-atiixp-modem overridden by hsfmc97ati
Current parameters: ("hsfconfig --info")
Config for modem unit 0: /dev/ttySHSF0
Device instance: 0-PCI-14f1:2f30-14f1:2075
HW revision : Basic2 2.18 Standard DAA 3VoltsIA
HW profile name: hsfpcibasic2hsfi
Current region : IRAN* (T.35 code: 0055)
The /dev/modem alias (symlink) points to ttySHSF0
با درایوری که بهم معرفی کردی تونستم نصبش کنم و دستت درد نکنه . نمی دونم با این مشکل چکار کنم!!!!!!!!!!!!!!!!!!!!!!!!!!!!! ](*,)
مواردی که گفتی رو من کامل انجام دادم
در مورد log گرفتن از ppp کاری رو که گفتی من انجام دادم و این log رو بهم دادش:
linux@linux:~$ plog -f
Jul 30 22:26:10 linux chat[5282]: CONNECT
Jul 30 22:26:10 linux chat[5282]: -- got it
Jul 30 22:26:10 linux chat[5282]: send (^M)
Jul 30 22:26:10 linux chat[5282]: expect (ogin:)
Jul 30 22:26:10 linux chat[5282]: 115200 ^M
Jul 30 22:26:10 linux chat[5282]: ^M
Jul 30 22:26:10 linux chat[5282]: ^M
Jul 30 22:26:10 linux chat[5282]: User Access Verification^M
Jul 30 22:26:10 linux chat[5282]: ^M
Jul 30 22:26:10 linux chat[5282]: Username: ^M
Jul 30 22:26:42 linux chat[5282]: Username: ^M
Jul 30 22:26:42 linux chat[5282]: % Username: timeout expired!^M
Jul 30 22:26:42 linux chat[5282]: % Authentication failed.^M
Jul 30 22:26:42 linux chat[5282]: ^M
Jul 30 22:26:55 linux chat[5282]: alarm
Jul 30 22:26:55 linux chat[5282]: Failed
Jul 30 22:26:55 linux pppd[5280]: Connect script failed
Jul 30 22:26:56 linux pppd[5280]: Exit.
که بنظر می آد منظورش اینه که user&pass ام درس نیس
همون Error ی که wvdial می داد .
ولی من این رو 100 بار تست کردم. کاملا درستن.
در ظمن من method این ppp رو chat انتخاب کردم.