smartctl -d ata -a /dev/sda | grep 193; hdparm -B 180 /dev/sda; sleep 600; \
smartctl -d ata -a /dev/sda | grep 193; hdparm -B 255 /dev/sda
hdparam رو به ۱۲۸ و ۱۶۰ تغییر بدید که بدترین حالت ها هستنhdparm -B 255 /dev/sda
/dev/sda {
apm = 255
}
99-stop-hitachi-madness.sh
و با محتوای #!/bin/sh
hdparm -B 255 /dev/sda
ایجاد کنید و بعد به این شاخه ها کپی کنید/etc/acpi/suspend.d/
/etc/acpi/resume.d/
/etc/acpi/start.d/
CONTROL_HD_POWERMGMT=1
ظاهرا حق با شماست دوست عزیز. (فکر کنم شما همون کرگدن phalls.com باشی ;) )
ممنون از راهنماییت.
اضافه میکنم http://rss.slashdot.org/~r/Slashdot/slashdotLinux/~3/177298829/article.pl
سلام
احتمالش بقدری کم و ضعیف هست که من با قاطعیت می گم غیر ممکن هست !
نرم افزار نمی تونه به سخت افزاری چون هارد دیسک آسیب برسونه ! شاید موارد نادری (مخصوصا قبلنا) باشه اما این ضعف سخت افزار بود ! نرم افزار به سخت افزار دستور می ده که کاری رو انجام بده حالا اگر این کار باعث سوختنش یا خراب شدنش بشه که سخت افزار نباید انجامش بده !! مثلا نرم افزار دستور بده ولتاژ بره بالاتر !! اماکن داره ؟!؟! یا به هد دستور بده که ضربه بزنه به هارد ؟!؟!؟ امکان نداره ! هارد شما خراب بوده . البته سیستم عامل در دراز مدت می تونه تاثیر داشته باشه . برای مثال الگوریتم ها و روش های بهینه ای استفاده نشه و مقدار کار هد و هارد بالا بره .
این مشکل مختص اوبونتو نیست و به طور کلی ممکنه تعداد لود سیکل در دقیقه روی توزیع‌های مختلف بالا باشه. حتما امتحان کنید و ببینید اوضاع چطوریه. لپتاپ من با سه ماه عمر ۲۱۲۰۰۰ سیکل مصرف کرده! توجه داشته باشید روی همه ماشین‌ها ۲۵۵ جواب نمی‌ده. مثلا روی inspiron 6400 من B 254 -S60- جواب داد. راه حل:کد: [انتخاب]# vim /etc/hdparm.conf and add:
/dev/sda {
apm = 254
spindown_time = 60
}
سلامقطعاً می تونه آسیب برسونه !!!! یک ویروس هم بود که دقیقاً هارد رو از بین می برد. اسمش یادم نمیاد ولی طرز کارش اینطوری بود که به هارد دستور می داد که بیرونی ترین سکتور هارد رو بخونه ولی قبل از اینکه بتونه هد هارد به اونجا برسه دستور خاموش شدن و پارک رو به هارد ارسال می کرد و تا هارد می اومد دستور جدید رو اجرا کنه باز دستور خوندن سکتور و ....
احتمالش بقدری کم و ضعیف هست که من با قاطعیت می گم غیر ممکن هست !
نرم افزار نمی تونه به سخت افزاری چون هارد دیسک آسیب برسونه ! شاید موارد نادری (مخصوصا قبلنا) باشه اما این ضعف سخت افزار بود ! نرم افزار به سخت افزار دستور می ده که کاری رو انجام بده حالا اگر این کار باعث سوختنش یا خراب شدنش بشه که سخت افزار نباید انجامش بده !! مثلا نرم افزار دستور بده ولتاژ بره بالاتر !! اماکن داره ؟!؟! یا به هد دستور بده که ضربه بزنه به هارد ؟!؟!؟ امکان نداره ! هارد شما خراب بوده . البته سیستم عامل در دراز مدت می تونه تاثیر داشته باشه . برای مثال الگوریتم ها و روش های بهینه ای استفاده نشه و مقدار کار هد و هارد بالا بره .
mehdi@mehdi-laptop:~$ sudo smartctl -d ata -a /dev/sda
smartctl version 5.37 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Fujitsu MHT series
Device Model: FUJITSU MHT2040AH
Serial Number: NP0ET462ENV2
Firmware Version: 006C
User Capacity: 40,007,761,920 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 6
ATA Standard is: ATA/ATAPI-6 T13 1410D revision 3a
Local Time is: Sun Nov 4 00:51:22 2007 IRST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 121) The previous self-test completed having
the read element of the test failed.
Total time to complete Offline
data collection: ( 293) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 40) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 100 046 Pre-fail Always - 100649
2 Throughput_Performance 0x0005 100 100 030 Pre-fail Offline - 9961630
3 Spin_Up_Time 0x0003 100 100 025 Pre-fail Always - 1
4 Start_Stop_Count 0x0032 098 098 000 Old_age Always - 5873
5 Reallocated_Sector_Ct 0x0033 100 100 024 Pre-fail Always - 8589934592000
7 Seek_Error_Rate 0x000f 100 091 047 Pre-fail Always - 3392
8 Seek_Time_Performance 0x0005 100 100 019 Pre-fail Offline - 0
9 Power_On_Seconds 0x0032 084 084 000 Old_age Always - 8261h+10m+59s
10 Spin_Retry_Count 0x0013 100 100 020 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 5620
192 Power-Off_Retract_Count 0x0032 099 099 000 Old_age Always - 284
193 Load_Cycle_Count 0x0032 094 094 000 Old_age Always - 69565
194 Temperature_Celsius 0x0022 100 065 000 Old_age Always - 51 (Lifetime Min/Max 12/67)
195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 3447
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 286588928
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 099 099 000 Old_age Offline - 2
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x000f 100 100 060 Pre-fail Always - 21260
203 Run_Out_Cancel 0x0002 100 100 000 Old_age Always - 429568753054
SMART Error Log Version: 1
ATA Error Count: 20 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 20 occurred at disk power-on lifetime: 3963 hours (165 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 11 b9 cb e2 Error: UNC 1 sectors at LBA = 0x02cbb911 = 46905617
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 ff 01 11 b9 cb e2 00 01:27:32.859 READ DMA
ca ff 01 10 b9 cb e2 00 01:27:32.859 WRITE DMA
c8 ff 01 10 b9 cb e2 00 01:27:32.843 READ DMA
c8 ff 01 11 b9 cb e2 00 01:27:28.813 READ DMA
c8 ff 01 10 b9 cb e2 00 01:27:28.802 READ DMA
Error 19 occurred at disk power-on lifetime: 3963 hours (165 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 11 b9 cb e2 Error: UNC 1 sectors at LBA = 0x02cbb911 = 46905617
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 ff 01 11 b9 cb e2 00 01:27:28.813 READ DMA
c8 ff 01 10 b9 cb e2 00 01:27:28.802 READ DMA
c8 ff 01 0f b9 cb e2 00 01:27:28.802 READ DMA
c8 ff 01 0e b9 cb e2 00 01:27:28.794 READ DMA
c8 ff 01 0d b9 cb e2 00 01:27:28.794 READ DMA
Error 18 occurred at disk power-on lifetime: 3962 hours (165 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 9a a4 0d e0 Error: UNC 1 sectors at LBA = 0x000da49a = 894106
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 ff 01 9a a4 0d e0 00 00:13:34.898 READ DMA
ca ff 01 99 a4 0d e0 00 00:13:34.898 WRITE DMA
c8 ff 01 99 a4 0d e0 00 00:13:34.883 READ DMA
c8 ff 01 9a a4 0d e0 00 00:13:30.996 READ DMA
c8 ff 01 99 a4 0d e0 00 00:13:30.985 READ DMA
Error 17 occurred at disk power-on lifetime: 3962 hours (165 days + 2 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 9a a4 0d e0 Error: UNC 1 sectors at LBA = 0x000da49a = 894106
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 ff 01 9a a4 0d e0 00 00:13:30.996 READ DMA
c8 ff 01 99 a4 0d e0 00 00:13:30.985 READ DMA
c8 ff 01 98 a4 0d e0 00 00:13:30.465 READ DMA
c8 ff 01 97 a4 0d e0 00 00:13:30.456 READ DMA
c8 ff 01 96 a4 0d e0 00 00:13:30.456 READ DMA
Error 16 occurred at disk power-on lifetime: 3149 hours (131 days + 5 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 11 b9 cb 42 Error: UNC 1 sectors at LBA = 0x02cbb911 = 46905617
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 01 11 b9 cb 42 00 02:27:04.173 READ DMA
c8 00 01 10 b9 cb 42 00 02:27:04.172 READ DMA
c8 00 01 0f b9 cb 42 00 02:27:04.172 READ DMA
c8 00 01 0e b9 cb 42 00 02:27:04.147 READ DMA
c8 00 01 0d b9 cb 42 00 02:27:04.147 READ DMA
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed: read failure 90% 3145 46905617
# 2 Short offline Completed without error 00% 1853 -
# 3 Short offline Completed without error 00% 227 -
# 4 Short offline Completed without error 00% 0 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
mehdi@mehdi-laptop:~$
root@mehdi-laptop:/home/mehdi# smartctl -d ata -a /dev/sda | grep 193; hdparm -B 180 /dev/sda; sleep 600; \smartctl -d ata -a /dev/sda | grep 193; hdparm -B 255 /dev/sda
193 Load_Cycle_Count 0x0032 094 094 000 Old_age Always - 69565
/dev/sda:
setting Advanced Power Management level to 0xb4 (180)
193 Load_Cycle_Count 0x0032 094 094 000 Old_age Always - 69565
/dev/sda:
setting Advanced Power Management level to disabled
root@mehdi-laptop:/home/mehdi#
sudo smartctl -a /dev/sda | grep Load_Cycle_Countsudo hdparm -B 254 /dev/sda
sudo hdparm -S 0 /dev/sda
gksudo gedit /etc/hdparm.conf/dev/sda {
apm = 254
spindown_time = 0
}sudo update-rc.d hdparm defaultssudo gedit 99-hdd-spin-fix.sh #!/bin/sh
hdparm -B 254 /dev/sda
hdparm -S 0 /dev/sdasudo install 99-hdd-spin-fix.sh /etc/acpi/suspend.d/
sudo install 99-hdd-spin-fix.sh /etc/acpi/resume.d/
sudo install 99-hdd-spin-fix.sh /etc/acpi/start.d/
sudo install 99-hdd-spin-fix.sh /etc/acpi/ac.d/
sudo install 99-hdd-spin-fix.sh /etc/acpi/battery.d/sudo smartctl -a /dev/sda | grep Load_Cycle_Count
میشه مرجع این راه رو بدید که یه کمی مطالعه کنم؟
salam be in negah konin begin khobe ya bad
salam kargadan jan
8 mahi hast labtopamo kharidam
neveshte bodam ke harchand saniye yek bar yedone be on addad ezafe mishe
in bare aval
.
.
.
mamnon misham javabe daghigh va roshani behem bedid
saeed@saeed-laptop:~$ sudo smartctl --all /dev/sda | egrep "Cycle|Power_On"
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 3071
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 90
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 1754saeed@saeed-laptop:~$ sudo smartctl --all /dev/sda | egrep "Cycle|Power_On"
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 3099
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 90
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 1758با باطری وبرق که تست دقیق کردم نتایج در ویندوز و ابونتو مشابه هم بود... در هر ساعت حداقل 10 بار پیشرفت داره Load Cycle Count
در ویندوز در حالت Maximum Performance هم Load Cycle Count پیشرفت داره... وقتی که به برق وصله و هم در حالت باطری.
تو سایت توشیبا هم واسه این مدل هارد فریم ویر جدیدی منشتر نکردن...
راه حل دیگه ای هست ؟
smartctl version 5.37 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: FUJITSU MHW2160BJ G1
Serial Number: K314T8225A7E
Firmware Version: 0084001D
User Capacity: 160,041,885,696 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: Not recognized. Minor revision code: 0x42
Local Time is: Wed Apr 30 11:32:51 2008 PDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 526) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 72) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 100 046 Pre-fail Always - 236995
2 Throughput_Performance 0x0005 100 100 030 Pre-fail Offline - 27197440
3 Spin_Up_Time 0x0003 100 100 025 Pre-fail Always - 2
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 127
5 Reallocated_Sector_Ct 0x0033 100 100 024 Pre-fail Always - 8589934592000
7 Seek_Error_Rate 0x000f 100 100 047 Pre-fail Always - 3044
8 Seek_Time_Performance 0x0005 100 100 019 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 158
10 Spin_Retry_Count 0x0013 100 100 020 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 78
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 7
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 5118
194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 33 (Lifetime Min/Max 20/48)
195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 8
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 456523776
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 253 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x000f 100 100 060 Pre-fail Always - 18415
203 Run_Out_Cancel 0x0002 100 100 000 Old_age Always - 2628538466038
240 Head_Flying_Hours 0x003e 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
mohi@laptop:~$ sudo smartctl --all /dev/sda | egrep "Cycle|Power_On"
9 Power_On_Hours 0x0032 252 252 000 Old_age Always - 389
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 256فکر کنم این مشکل توی هاردی خیلی بهتر شده! (یا توهمه؟ ;) )کد: [انتخاب]mohi@laptop:~$ sudo smartctl --all /dev/sda | egrep "Cycle|Power_On"
9 Power_On_Hours 0x0032 252 252 000 Old_age Always - 389
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 256
اطلاعات برای dell vostro 1500 هست.
smartctl -d ata -a /dev/sda | grep 193; hdparm -B 180 /dev/sda; sleep 600; \
smartctl -d ata -a /dev/sda | grep 193; hdparm -B 255 /dev/sdaمرحله اول به صورت زیر شودfarshid@farshid-laptop:~$ smartctl -d ata -a /dev/sda | grep 193; hdparm -B 180 /dev/sda; sleep 600; \
> smartctl -d ata -a /dev/sda | grep 193; hdparm -B 255 /dev/sda
/dev/sda: Permission denied
و بعد از ۱۰ دقیقه خط زیر اضافه شد/dev/sda: Permission denied
sudo smartctl -a /dev/sda | grep Load_Cycle_Countدوبار به فاصله ۱۰ دقیقه اجراش کردم و از 11936 به 11943 رسید کمه اما باید متوقف بشه درسته؟؟!!با سلامدرود
بحث واقعا مهمی رو راه انداختین ! ازتون متشکرم...
من دستور زیر رو اجرا کردمکد: [انتخاب]smartctl -d ata -a /dev/sda | grep 193; hdparm -B 180 /dev/sda; sleep 600; \مرحله اول به صورت زیر شود
smartctl -d ata -a /dev/sda | grep 193; hdparm -B 255 /dev/sdaکد: [انتخاب]farshid@farshid-laptop:~$ smartctl -d ata -a /dev/sda | grep 193; hdparm -B 180 /dev/sda; sleep 600; \و بعد از ۱۰ دقیقه خط زیر اضافه شد
> smartctl -d ata -a /dev/sda | grep 193; hdparm -B 255 /dev/sda
/dev/sda: Permission deniedکد: [انتخاب]/dev/sda: Permission denied
بعد رفتم سراغ دستور زیرکد: [انتخاب]sudo smartctl -a /dev/sda | grep Load_Cycle_Countدوبار به فاصله ۱۰ دقیقه اجراش کردم و از 11936 به 11943 رسید کمه اما باید متوقف بشه درسته؟؟!!
لطفا من رو راهنمایی کنید
farshid@farshid-laptop:~$ sudo update-rc.d hdparm defaults
update-rc.d: /etc/init.d/hdparm: file does not exist
sudo touch /etc/init.d/hdparmsudo hdparm -B 254 /dev/sda
sudo hdparm -S 0 /dev/sdaرو پشت سر هم در یک خط add کردماین دستور رو بزنید:کد: [انتخاب]sudo touch /etc/init.d/hdparm
و بعدش از همونجا که خطا داد، ادامه بدید. امیدوارم حل بشه. :)
راهی که آوردم فکر کنم بهتره. چون روی Suspend و Hibernate و چیزای دیگه هم اثر داره. ولی این یکی راه شما فقط به شرط لاگین کردن کار میکنه.
ایجاد کنید و بعد به این شاخه ها کپی کنیدکد: [انتخاب]
/etc/acpi/suspend.d/
/etc/acpi/resume.d/
/etc/acpi/start.d/
ازهمگی ممنونم مخصوصا lomion وکرگدن.
آقا من به این چک کردن ها گیر دادم می خوام بدونم طبق چه رابطه ای اضافه می شه؟
ساعت 11:30َAM تعداد سیکل 1943 بود و 12 ساعت بعدش 12005 شده تواین مدت هم بی قاعده پیشروی کرده.
گیج شدم ???
sudo smartctl -a /dev/sda | grep Load_Cycle_Countبرای من هیچ خروجی نداره؟ ???
به نظر شما چراکد: [انتخاب]sudo smartctl -a /dev/sda | grep Load_Cycle_Countبرای من هیچ خروجی نداره؟ ???
تمام بقیه دستورا نصب کار میکنن. grep رو هم اگه بردارم مینویسه که دستورو پیدا نمیکنیم ;)
اون برنامه رو تازه نصب کردم. این دستور هیچ وقت حتی توی گاتسی برای من خروجی نداشته! :)
apt-get install smartmontoolsgrep رو برداری بقیه خروجی ها رو داره؟این کار رو که میکنم میگه این دستور not found ;)
به این برنامهه که برای دل هست( نصب کردی؟ ) ربطی نداره؟ :)
اگر دیوایس هاردت رو هم درست معرفی نکنی خروجی ندارهبله. بقیه دستورات خروجی دارن همیشه. فقط این یکی نداره! ](*,) ;D
هاردت همین sda هست؟
اگر دیوایس هاردت رو هم درست معرفی نکنی خروجی ندارهبله. بقیه دستورات خروجی دارن همیشه. فقط این یکی نداره! ](*,) ;D
هاردت همین sda هست؟
mohi@laptop:~$ sudo smartctl -a /dev/sda | grep Load_Cycle_Count
mohi@laptop:~$ sudo smartctl -a /dev/sda | Load_Cycle_Count
bash: Load_Cycle_Count: command not found
کد: [انتخاب]mohi@laptop:~$ sudo smartctl -a /dev/sda | grep Load_Cycle_Count
mohi@laptop:~$ sudo smartctl -a /dev/sda | Load_Cycle_Count
bash: Load_Cycle_Count: command not found
sudo smartctl -a /dev/sdasudo fdisk -l
~$ sudo smartctl -a /dev/sda
smartctl version 5.37 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: SAMSUNG HM160HI
Serial Number: S14QJD0PB67711
Firmware Version: HH100-11
User Capacity: 160,041,885,696 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0
Local Time is: Fri May 30 23:13:34 2008 IRDT
==> WARNING: May need -F samsung or -F samsung2 enabled; see manual for details.
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 32) The self-test routine was interrupted
by the host with a hard or soft reset.
Total time to complete Offline
data collection: ( 60) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 60) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 100 051 Pre-fail Always - 149
3 Spin_Up_Time 0x0007 252 252 025 Pre-fail Always - 2000
4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 18345
5 Reallocated_Sector_Ct 0x0033 252 252 010 Pre-fail Always - 0
9 Power_On_Hours 0x0032 252 252 000 Old_age Always - 446
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 316
191 G-Sense_Error_Rate 0x0032 022 022 000 Old_age Always - 794417
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 23
194 Temperature_Celsius 0x0022 109 100 000 Old_age Always - 43 (Lifetime Min/Max 8/46)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 25148
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 311
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 706
199 UDMA_CRC_Error_Count 0x0036 252 252 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x000a 252 252 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Aborted by host 150% 83 -
# 2 Short offline Completed without error 00% 2 -
# 3 Extended offline Completed without error 00% 0 -
# 4 Short offline Completed without error 00% 0 -
SMART Selective Self-Test Log Data Structure Revision Number (0) should be 1
SMART Selective self-test log data structure revision number 0
Warning: ATA Specification requires selective self-test log data structure revision number = 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Interrupted [00% left] (0-65535)
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
~$ sudo fdisk -l
Disk /dev/sda: 160.0 GB, 160041885696 bytes
255 heads, 63 sectors/track, 19457 cylinders
Units = cylinders of 16065 * 512 = 8225280 bytes
Disk identifier: 0x08000000
Device Boot Start End Blocks Id System
/dev/sda1 1 10 80293+ de Dell Utility
/dev/sda2 11 1316 10485760 7 HPFS/NTFS
/dev/sda3 * 1316 4963 29296875 7 HPFS/NTFS
/dev/sda4 4964 19458 116423696 f W95 Ext'd (LBA)
/dev/sda5 19131 19458 2620416 dd Unknown
/dev/sda6 4964 6786 14643216 83 Linux
/dev/sda7 18888 19130 1951866 82 Linux swap / Solaris
/dev/sda8 6787 18887 97201251 83 Linux
Partition table entries are not in disk order
اه! نامردا چرا من Load_Cycle_Count ندارم تو اینجا ولی بقیه دارن؟ ???
sudo smartctl -A /dev/sda
~$ sudo smartctl -A /dev/sda
[sudo] password for mohi:
smartctl version 5.37 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF READ SMART DATA SECTION ===
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 100 051 Pre-fail Always - 149
3 Spin_Up_Time 0x0007 252 252 025 Pre-fail Always - 2000
4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 18345
5 Reallocated_Sector_Ct 0x0033 252 252 010 Pre-fail Always - 0
9 Power_On_Hours 0x0032 252 252 000 Old_age Always - 447
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 316
191 G-Sense_Error_Rate 0x0032 022 022 000 Old_age Always - 794457
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 23
194 Temperature_Celsius 0x0022 112 100 000 Old_age Always - 42 (Lifetime Min/Max 8/46)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 25192
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 311
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 706
199 UDMA_CRC_Error_Count 0x0036 252 252 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x000a 252 252 000 Old_age Always - 0
root@sohail-laptop:/home/sohail# smartctl -d ata -a /dev/sda | grep 193; hdparm -B 180 /dev/sda; sleep 600; \
> smartctl -d ata -a /dev/sda | grep 193; hdparm -B 255 /dev/sda
193 Load_Cycle_Count 0x0032 099 099 000 Old_age Always - 24193
/dev/sda:
setting Advanced Power Management level to 0xb4 (180)
193 Load_Cycle_Count 0x0032 099 099 000 Old_age Always - 24197
/dev/sda:
setting Advanced Power Management level to disabled
=== START OF INFORMATION SECTION ===
Device Model: FUJITSU MHW2160BH PL
Serial Number: K10NT772HY0W
Firmware Version: 891F
User Capacity: 160,041,885,696 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 7
ATA Standard is: ATA/ATAPI-7 T13 1532D revision 4a
Local Time is: Mon Jul 7 12:32:13 2008 IRDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
ممنون از پست جالبتون.
میشه بگین تو ۶۰۰ ثانیه چقدر تغییر قابل قبوله؟ برای من ۴ تا اضافه شد، یعنی اوضاع چطوره؟ توی اون گزارش باگ نوشته كه بايد حدود ساعتی 15 تا باشه، يعنی مال من كه ساعتی 24 تا است زياده؟
از من روی Dell 1520 از بیخ و بن متوقف شده! الان دو روزه که حتی یکی هم اضافه نشده روی 2175 باقی مونده....می ترسین هاردتون ایست قلبی کرده باشه؟ :P
یعنی طبیعیه...؟!
سلامقطعاً می تونه آسیب برسونه !!!! یک ویروس هم بود که دقیقاً هارد رو از بین می برد. اسمش یادم نمیاد ولی طرز کارش اینطوری بود که به هارد دستور می داد که بیرونی ترین سکتور هارد رو بخونه ولی قبل از اینکه بتونه هد هارد به اونجا برسه دستور خاموش شدن و پارک رو به هارد ارسال می کرد و تا هارد می اومد دستور جدید رو اجرا کنه باز دستور خوندن سکتور و ....
احتمالش بقدری کم و ضعیف هست که من با قاطعیت می گم غیر ممکن هست !
نرم افزار نمی تونه به سخت افزاری چون هارد دیسک آسیب برسونه ! شاید موارد نادری (مخصوصا قبلنا) باشه اما این ضعف سخت افزار بود ! نرم افزار به سخت افزار دستور می ده که کاری رو انجام بده حالا اگر این کار باعث سوختنش یا خراب شدنش بشه که سخت افزار نباید انجامش بده !! مثلا نرم افزار دستور بده ولتاژ بره بالاتر !! اماکن داره ؟!؟! یا به هد دستور بده که ضربه بزنه به هارد ؟!؟!؟ امکان نداره ! هارد شما خراب بوده . البته سیستم عامل در دراز مدت می تونه تاثیر داشته باشه . برای مثال الگوریتم ها و روش های بهینه ای استفاده نشه و مقدار کار هد و هارد بالا بره .
توی سایت دبیرستانم، همه هارد دیسک ها همینجوری سوختن !!! :D
می خواستم ببینم که این موضوع تو اوبونتو ۸.۰۴ هم صدق می کنه ؟بله
#sudo smartctl -a /dev/sda | grep Load_Cycle_Count
193 Load_Cycle_Count 0x0032 198 198 000 Old_age Always - 6269
#sudo smartctl -a /dev/sda | grep Load_Cycle_Count
193 Load_Cycle_Count 0x0032 198 198 000 Old_age Always - 6274
soroush@soroush-laptop:~$ sudo smartctl -a /dev/sda | grep Load_Cycle_Count
193 Load_Cycle_Count 0x0032 198 198 000 Old_age Always - 6291
soroush@soroush-laptop:~$ sudo update-rc.d hdparm defaults
update-rc.d: /etc/init.d/hdparm: file does not exist
مشکلی نیست؟؟؟soroush@soroush-laptop:~$ sudo smartctl -a /dev/sda | grep Load_Cycle_Count
193 Load_Cycle_Count 0x0032 198 198 000 Old_age Always - 6291
soroush@soroush-laptop:~$ sudo smartctl -d ata -a /dev/sda
smartctl version 5.37 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Scorpio family
Device Model: WDC WD1200BEVS-75UST0
Serial Number: WD-WXC408567161
Firmware Version: 01.01A01
User Capacity: 120,034,123,776 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Mon Sep 1 19:55:24 2008 EEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (4800) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 60) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 200 200 051 Pre-fail Always - 1
3 Spin_Up_Time 0x0003 161 159 021 Pre-fail Always - 950
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 254
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x000e 100 253 051 Old_age Always - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 358
10 Spin_Retry_Count 0x0012 100 100 051 Old_age Always - 0
11 Calibration_Retry_Count 0x0012 100 100 051 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 232
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 29
193 Load_Cycle_Count 0x0032 198 198 000 Old_age Always - 6291
194 Temperature_Celsius 0x0022 106 097 000 Old_age Always - 37
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 100 253 051 Old_age Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 266 -
# 2 Short offline Completed without error 00% 1 -
# 3 Short offline Completed without error 00% 0 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
sudo touch /etc/init.d/hdparmبعدش هم این دستور:sudo chmod 755 /etc/init.d/hdparm
soroush@soroush-laptop:~$ sudo smartctl -a /dev/sda | grep Load_Cycle_Count
193 Load_Cycle_Count 0x0032 198 198 000 Old_age Always - 6368
soroush@soroush-laptop:~$ sudo smartctl -a /dev/sda | grep Load_Cycle_Count
193 Load_Cycle_Count 0x0032 198 198 000 Old_age Always - 6522
soroush@soroush-laptop:~$ sudo smartctl -d ata -a /dev/sdasmartctl version 5.37 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Scorpio family
Device Model: WDC WD1200BEVS-75UST0
Serial Number: WD-WXC408567161
Firmware Version: 01.01A01
User Capacity: 120,034,123,776 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Wed Sep 10 18:55:38 2008 EEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (4800) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 60) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 200 200 051 Pre-fail Always - 1
3 Spin_Up_Time 0x0003 159 159 021 Pre-fail Always - 1008
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 267
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x000e 100 253 051 Old_age Always - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 400
10 Spin_Retry_Count 0x0012 100 100 051 Old_age Always - 0
11 Calibration_Retry_Count 0x0012 100 100 051 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 245
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 31
193 Load_Cycle_Count 0x0032 198 198 000 Old_age Always - 6524
194 Temperature_Celsius 0x0022 105 097 000 Old_age Always - 38
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 100 253 051 Old_age Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 266 -
# 2 Short offline Completed without error 00% 1 -
# 3 Short offline Completed without error 00% 0 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
برای اون خط این دستور ر اجرا کنید و باز از ادامه همون روش، مراحل رو تکرار کنید:کد: [انتخاب]sudo touch /etc/init.d/hdparmبعدش هم این دستور:کد: [انتخاب]sudo chmod 755 /etc/init.d/hdparm
sudo update-rc.d hdparm defaultsرو اجرا کردم و خطا گرفت. بعد این دو خطی که گفتین رو اجرا کردم و دوباره همون کد اولیه رو. این دفعه خطایی در کار نبود و یه چیزهایی نوشت (مثل updating something -> something). آیا کاری که کردم درست بوده؟
essiprog@essiprog-laptop:~$ smartctl -d ata -a /dev/sda
smartctl version 5.37 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
Smartctl open device: /dev/sda failed: Permission denied
essiprog@essiprog-laptop:~$ sudo smartctl -d ata -a /dev/sda
smartctl version 5.37 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: FUJITSU MHY2200BH
Serial Number: K41KT832P21E
Firmware Version: 0000000B
User Capacity: 200,049,647,616 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: Not recognized. Minor revision code: 0x42
Local Time is: Thu Jan 10 15:15:26 2008 IRST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 811) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 115) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 100 046 Pre-fail Always - 159162
2 Throughput_Performance 0x0005 100 100 030 Pre-fail Offline - 45023232
3 Spin_Up_Time 0x0003 100 100 025 Pre-fail Always - 1
4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 2493
5 Reallocated_Sector_Ct 0x0033 100 100 024 Pre-fail Always - 8589934592000
7 Seek_Error_Rate 0x000f 100 100 047 Pre-fail Always - 181
8 Seek_Time_Performance 0x0005 100 100 019 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 096 096 000 Old_age Always - 2027
10 Spin_Retry_Count 0x0013 100 100 020 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 1433
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 75
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 9235
194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 39 (Lifetime Min/Max 22/53)
195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 12
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 457113600
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 253 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x000f 100 100 060 Pre-fail Always - 31876
203 Run_Out_Cancel 0x0002 100 100 000 Old_age Always - 2628585717262
240 Head_Flying_Hours 0x003e 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
essiprog@essiprog-laptop:~$ smartctl -d ata -a /dev/sda
smartctl version 5.37 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
Smartctl open device: /dev/sda failed: Permission denied
essiprog@essiprog-laptop:~$ sudo smartctl -d ata -a /dev/sda
smartctl version 5.37 [i686-pc-linux-gnu] Copyright (C) 2002-6 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: FUJITSU MHY2200BH
Serial Number: K41KT832P21E
Firmware Version: 0000000B
User Capacity: 200,049,647,616 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: Not recognized. Minor revision code: 0x42
Local Time is: Thu Jan 10 15:23:17 2008 IRST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 811) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 115) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 100 046 Pre-fail Always - 157096
2 Throughput_Performance 0x0005 100 100 030 Pre-fail Offline - 45023232
3 Spin_Up_Time 0x0003 100 100 025 Pre-fail Always - 1
4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 2493
5 Reallocated_Sector_Ct 0x0033 100 100 024 Pre-fail Always - 8589934592000
7 Seek_Error_Rate 0x000f 100 100 047 Pre-fail Always - 634
8 Seek_Time_Performance 0x0005 100 100 019 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 096 096 000 Old_age Always - 2027
10 Spin_Retry_Count 0x0013 100 100 020 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 1433
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 75
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 9235
194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 40 (Lifetime Min/Max 22/53)
195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 41
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 457113600
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 253 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x000f 100 100 060 Pre-fail Always - 32642
203 Run_Out_Cancel 0x0002 100 100 000 Old_age Always - 2628584734249
240 Head_Flying_Hours 0x003e 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
سپاس از کرگدن عزیز
مقدار سایکل استفاده شده تا الان چقدر هستش؟
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 9235
Spinning Down the Hard Disk
All modern hard disks come with the ability to spin down their motors to save energy.
Then, when data is requested, the motors spin up again. There may be a slight delay while
this happens, and some people dislike using disk spin-down because of this. However, on
a notebook, it can lead to a substantial increase in battery life. On a desktop system, it’s
worth considering, because over the lifetime of a computer, it can save a lot of electricity
(and therefore money!).
The spin-down settings are contained in the /etc/hdparm.conf file, which you’ll need
to edit by hand. Follow these steps to adjust the spin-down settings:
1. Open a terminal window (Applications ➤ Accessories ➤ Terminal) and type
the following:
gksu gedit /etc/hdparm.conf
2. Click Search ➤ Find, and in the box, type spindown_time.
3. Click the Find button. You should find that a line in the file is now highlighted.
Close the Search dialog box.
4. Change the line to remove the hash mark from the beginning, so it reads like this:
spindown_time = 24
You can alter the value to anything you want. Each time unit is five seconds, so 24
equates to 120 seconds (24×5 seconds) or 2 minutes. To set a time of 20 minutes,
enter 240 (240×5 seconds). If you specify a number above 240, the time units are
increased to 30 minutes. In other words, a value of 241 will equate to 30 minutes, a
value of 242 will equate to 60 minutes, and so on.
5. When you’ve finished, save the file.
6. Reboot for the settings to take effect.با این راهنمایی قضیه به طور کامل حل نمیشه؟sudo update-rc.d hdparm defaultsایراد زیر رو می‌گیره:update-rc.d: /etc/init.d/hdparm: file does not existمیشه راهنمایی کنی چه کار باید بکنم؟دوستان نسخه لبتاب اوبونتو رو نصب کنید همه چی حلهسلام.منظورتون از نسخه لپتاپ اوبونتو چیه؟ :o
من بعد ۳۰ مین چک کردم عدد ثابت بود \\:D/
منظور ایشون ابونتو مخصوص نوت‌بوک هست که برای پردازنده‌های پایین و کلا برای نوت‌بوک‌ها طراحی شده!دوستان نسخه لبتاب اوبونتو رو نصب کنید همه چی حلهسلام.منظورتون از نسخه لپتاپ اوبونتو چیه؟ :o
من بعد ۳۰ مین چک کردم عدد ثابت بود \\:D/
نکنه منظورت از نوت بوک با پردازنده پایین و...همون نتبوک(netbook) است؟ :oمنظور ایشون ابونتو مخصوص نوت‌بوک هست که برای پردازنده‌های پایین و کلا برای نوت‌بوک‌ها طراحی شده!دوستان نسخه لبتاب اوبونتو رو نصب کنید همه چی حلهسلام.منظورتون از نسخه لپتاپ اوبونتو چیه؟ :o
من بعد ۳۰ مین چک کردم عدد ثابت بود \\:D/
تمش رو آقا مهدی تو میزکار سه‌بعدی گذاشته بودن میتونی بری ببینی.
درسته 'و' نداره ;)نکنه منظورت از نوت بوک با پردازنده پایین و...همون نتبوک(netbook) است؟ :oمنظور ایشون ابونتو مخصوص نوت‌بوک هست که برای پردازنده‌های پایین و کلا برای نوت‌بوک‌ها طراحی شده!دوستان نسخه لبتاب اوبونتو رو نصب کنید همه چی حلهسلام.منظورتون از نسخه لپتاپ اوبونتو چیه؟ :o
من بعد ۳۰ مین چک کردم عدد ثابت بود \\:D/
تمش رو آقا مهدی تو میزکار سه‌بعدی گذاشته بودن میتونی بری ببینی.
sudo update-rc.d hdparm defaultsبا دستوراتی که کرگدن دادن (راه دوم http://forum.ubuntu.ir/index.php/topic,2647.msg26194.html#msg26194) اضافه شدن این عدد متوقف شده اما برای دائمی کردن این روش که کددرست مطالعه نکردی جونم ;)کد: [انتخاب]sudo update-rc.d hdparm defaults
را وارد میکنم با مشکل باقی دوستان مواجه میشم یعنی عدم وجود فایل hdparm
راه حل چیست؟
نکنه منظورت از نوت بوک با پردازنده پایین و...همون نتبوک(netbook) است؟ :oمنظور ایشون ابونتو مخصوص نوت‌بوک هست که برای پردازنده‌های پایین و کلا برای نوت‌بوک‌ها طراحی شده!دوستان نسخه لبتاب اوبونتو رو نصب کنید همه چی حلهسلام.منظورتون از نسخه لپتاپ اوبونتو چیه؟ :o
من بعد ۳۰ مین چک کردم عدد ثابت بود \\:D/
تمش رو آقا مهدی تو میزکار سه‌بعدی گذاشته بودن میتونی بری ببینی.
کسی نمی خواد جواب بده......؟ ::)
نمی دونم چرا جدیدا این انجمن این طوری شده.....به جرات میتونم بگم حداقل به ۱۰ تا پست اخرم هیچ جوابی داده نشده...
سئوالات شما هم بیشتر در خصوص مشکلاتتون با این دستگاه هستش ، خوب مسلما بایستی یه نفر با این مدل تست زده باشه تا بتونه جواب بده
اگر اشتباه میگم بفرمائید
سلام من نوت بوک سوزوکی دارم با هارد هیتاچی...ولی این کدی که تو صفحه اوله رو اجرا کردم بعد ۱۰ دقیقه عدد ثابت بود...و چند دقیقه بعد دوباره زدم حدود ده بیست تا تغییر کرده بود...در مورد سوال اولت بگم که همونطور که جناب کرگدن به من تو همین تاپیک گفته تعداد چرخه‌ها باید متوقف بشه! این بهترین حالت هست!
میشه بگید که این مقدار تغییر خوبه یا بد؟
در ضمن اون اسکریپت هارو هم درست کردم و کپی کردم ولی دفعه بعدش دیگه سیستم بالا نیومد :D ::) البته تستی رو که بالا گفتم قبل درست کردن و کپی اسکریپت ها انجام دادم
کد: [انتخاب]gksudo gedit /etc/hdparm.conf
و بعد آخر فایل این رو وارد کنید:کد: [انتخاب]/dev/sda {
apm = 254
spindown_time = 0
}
حالا این راه حل رو باید برای هر بوت به کار گرفت:کد: [انتخاب]sudo update-rc.d hdparm defaults
update-rc.d: warning: /etc/init.d/hdparm missing LSB information
update-rc.d: see <http://wiki.debian.org/LSBInitScripts>
System start/stop links for /etc/init.d/hdparm already exist.
راستش وقتی به فایل دست نخورده نگاه میکنم اصلا هیچ دستوری نداره، تماما comment هست به جز یک دستور quiet. میشه راهنمایی کنید؟
و بعد فایل رو باید به جاهایی کپی کنید که دستوراتش اینه:کد: [انتخاب]sudo install 99-hdd-spin-fix.sh /etc/acpi/suspend.d/
sudo install 99-hdd-spin-fix.sh /etc/acpi/resume.d/
sudo install 99-hdd-spin-fix.sh /etc/acpi/start.d/
sudo install 99-hdd-spin-fix.sh /etc/acpi/ac.d/
sudo install 99-hdd-spin-fix.sh /etc/acpi/battery.d/
و تمام!
تست کنید ببینید که load cycle count هست یا نه. اگه نیست که خب این پست فقط همون مساله ر حل می کنه.
pezhman@pezhman-ubuntu:~$ sudo smartctl -d ata -a /dev/sda
smartctl version 5.38 [x86_64-unknown-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: WDC WD3200BEVS-26VAT0
Serial Number: WD-WX80A99E2834
Firmware Version: 11.01A11
User Capacity: 320,072,933,376 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Fri Jun 18 23:54:56 2010 IRDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (9960) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 118) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x303f) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 187 186 021 Pre-fail Always - 1633
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 817
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 100 253 000 Old_age Always - 0
9 Power_On_Hours 0x0032 099 099 000 Old_age Always - 1451
10 Spin_Retry_Count 0x0033 100 100 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 807
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 52
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 2676
194 Temperature_Celsius 0x0022 104 099 000 Old_age Always - 43
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0009 100 253 051 Pre-fail Offline - 0
SMART Error Log Version: 1
ATA Error Count: 54 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 54 occurred at disk power-on lifetime: 345 hours (14 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 5d aa 84 40
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 10 58 aa 84 0a 00 01:16:12.622 READ FPDMA QUEUED
2f 00 01 10 00 00 00 00 01:16:12.622 READ LOG EXT
60 08 08 58 aa 84 0a 00 01:16:09.374 READ FPDMA QUEUED
ef 02 00 00 00 00 00 00 01:16:08.378 SET FEATURES [Enable write cache]
ef 03 46 00 00 00 00 00 01:16:08.378 SET FEATURES [Set transfer mode]
Error 53 occurred at disk power-on lifetime: 345 hours (14 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 5d aa 84 40
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 08 58 aa 84 0a 00 01:16:09.374 READ FPDMA QUEUED
ef 02 00 00 00 00 00 00 01:16:08.378 SET FEATURES [Enable write cache]
ef 03 46 00 00 00 00 00 01:16:08.378 SET FEATURES [Set transfer mode]
c6 00 10 00 00 00 00 00 01:16:08.378 SET MULTIPLE MODE
60 08 58 58 aa 84 0a 00 01:16:05.016 READ FPDMA QUEUED
Error 52 occurred at disk power-on lifetime: 345 hours (14 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 5d aa 84 40
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 58 58 aa 84 0a 00 01:16:05.016 READ FPDMA QUEUED
2f 00 01 10 00 00 00 00 01:16:05.016 READ LOG EXT
60 08 50 58 aa 84 0a 00 01:16:01.934 READ FPDMA QUEUED
2f 00 01 10 00 00 00 00 01:16:01.934 READ LOG EXT
60 08 48 58 aa 84 0a 00 01:15:58.586 READ FPDMA QUEUED
Error 51 occurred at disk power-on lifetime: 345 hours (14 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 5d aa 84 40
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 50 58 aa 84 0a 00 01:16:01.934 READ FPDMA QUEUED
2f 00 01 10 00 00 00 00 01:16:01.934 READ LOG EXT
60 08 48 58 aa 84 0a 00 01:15:58.586 READ FPDMA QUEUED
2f 00 01 10 00 00 00 00 01:15:58.585 READ LOG EXT
60 08 40 58 aa 84 0a 00 01:15:55.503 READ FPDMA QUEUED
Error 50 occurred at disk power-on lifetime: 345 hours (14 days + 9 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 5d aa 84 40
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 08 48 58 aa 84 0a 00 01:15:58.586 READ FPDMA QUEUED
2f 00 01 10 00 00 00 00 01:15:58.585 READ LOG EXT
60 08 40 58 aa 84 0a 00 01:15:55.503 READ FPDMA QUEUED
2f 00 01 10 00 00 00 00 01:15:55.503 READ LOG EXT
60 08 38 58 aa 84 0a 00 01:15:52.421 READ FPDMA QUEUED
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
دو تا سوال
یکی اینکه این مشکل آیا در کامپیوتر های دسکتاپ هم وجود داره یا منحصرا برای هارد لپ تاپ پیش میاد؟
دوم اینکه آیا این معضل در نسخه های 10.04 و نسخه بعدی (آزمایشی) حل نشده!؟؟!
=== START OF INFORMATION SECTION ===
Device Model: HITACHI HTS725025A9A361 FDE
Serial Number: 100310PCK204VJGUZ9BJ
Firmware Version: PC2LC70F
User Capacity: 250,059,350,016 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 6
Local Time is: Fri Nov 5 16:23:57 2010 IRST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 645) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 67) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 062 Pre-fail Always - 0
2 Throughput_Performance 0x0005 100 100 040 Pre-fail Offline - 0
3 Spin_Up_Time 0x0007 242 242 033 Pre-fail Always - 1
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 893
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 040 Pre-fail Offline - 0
9 Power_On_Hours 0x0012 097 097 000 Old_age Always - 1397
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 738
191 G-Sense_Error_Rate 0x000a 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 371327032
193 Load_Cycle_Count 0x0012 098 098 000 Old_age Always - 22029
194 Temperature_Celsius 0x0002 134 134 000 Old_age Always - 41 (Lifetime Min/Max 22/53)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
223 Load_Retry_Count 0x000a 100 100 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 1284 -
# 2 Short offline Completed without error 00% 1242 -
# 3 Short offline Completed without error 00% 1221 -
# 4 Short offline Completed without error 00% 1220 -
# 5 Short offline Completed without error 00% 1220 -
# 6 Short offline Completed without error 00% 1220 -
# 7 Short offline Completed without error 00% 1219 -
# 8 Short offline Completed without error 00% 1219 -
# 9 Short offline Completed without error 00% 1219 -
#10 Short offline Completed without error 00% 1218 -
#11 Short offline Completed without error 00% 1218 -
#12 Short offline Completed without error 00% 1218 -
#13 Short offline Completed without error 00% 1046 -
#14 Short offline Completed without error 00% 760 -
#15 Short offline Completed without error 00% 760 -
#16 Short offline Completed without error 00% 494 -
#17 Short offline Completed without error 00% 76 -
#18 Short offline Completed without error 00% 76 -
#19 Short offline Completed without error 00% 11 -
#20 Vendor offline Completed without error 00% 0 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.سلام
ساعتی ۵۰ تا ۶۰ زیاده؟
اینکه چقدر می مونه، یه حساب سرانگشتی هست. توی گنوم امکانی هست توی قسمت پاور که اسپین رو میشه غیر فعال کرد. شاید اون ۱۰-۱۱تای از اونجا باشه. بعضی هم حساب مثل M.S.R می کنن می گن اشکالی نداره. هارد رو عوض می کنم .خوب من فعلاْ انقدر پولدار نیستم :)!
sudo smartctl -a /dev/sda | grep Load_Cycle_Count
193 Load_Cycle_Count 0x0032 094 094 000 Old_age Always - 13122
sudo smartctl -d ata -a /dev/sda
smartctl 5.40 2010-07-12 r3124 [x86_64-unknown-linux-gnu] (local build)
Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Model Family: Seagate Momentus 7200.4 series
Device Model: ST9500420AS
Serial Number: 5VJ7P8E6
Firmware Version: 0006HPM1
User Capacity: 500,107,862,016 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 4
Local Time is: Tue Jun 14 00:55:58 2011 IRDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 107) minutes.
SCT capabilities: (0x103f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 119 099 006 Pre-fail Always - 207828689
3 Spin_Up_Time 0x0002 097 097 000 Old_age Always - 0
4 Start_Stop_Count 0x0033 100 100 000 Pre-fail Always - 705
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 072 060 030 Pre-fail Always - 4310433085
9 Power_On_Hours 0x0032 099 099 000 Old_age Always - 1221
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0033 100 037 020 Pre-fail Always - 649
183 Runtime_Bad_Block 0x0032 100 253 000 Old_age Always - 0
184 End-to-End_Error 0x0033 100 100 097 Pre-fail Always - 0
187 Reported_Uncorrect 0x0032 098 098 000 Old_age Always - 2
188 Command_Timeout 0x0032 100 097 000 Old_age Always - 448
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 060 046 045 Old_age Always - 40 (Lifetime Min/Max 36/47)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 2
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 26
193 Load_Cycle_Count 0x0032 094 094 000 Old_age Always - 13122
194 Temperature_Celsius 0x0022 040 054 000 Old_age Always - 40 (0 16 0 0)
195 Hardware_ECC_Recovered 0x001a 047 043 000 Old_age Always - 207828689
196 Reallocated_Event_Count 0x0033 100 100 036 Pre-fail Always - 0
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
254 Free_Fall_Sensor 0x0032 100 100 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Aborted by host 90% 965 -
# 2 Short offline Aborted by host 90% 965 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
smartctl 5.40 2010-03-16 r3077 [x86_64-unknown-linux-gnu] (local build)
Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Device Model: HITACHI HTS545032B9A300
Serial Number: 100417PBPC041DK0SD1M
Firmware Version: PB3ZC61H
User Capacity: 320,072,933,376 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 6
Local Time is: Sun Jun 26 00:36:32 2011 IRDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 645) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 106) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 062 Pre-fail Always - 0
2 Throughput_Performance 0x0005 100 100 040 Pre-fail Offline - 0
3 Spin_Up_Time 0x0007 141 141 033 Pre-fail Always - 2
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 283
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 040 Pre-fail Offline - 0
9 Power_On_Hours 0x0012 092 092 000 Old_age Always - 3532
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 280
191 G-Sense_Error_Rate 0x000a 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 17
193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 7051
194 Temperature_Celsius 0x0002 117 117 000 Old_age Always - 47 (Lifetime Min/Max 13/53)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
223 Load_Retry_Count 0x000a 100 100 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Vendor offline Completed without error 00% 4 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
prince@prince-ESPRIMO-Mobile-V6535:~$ sudo smartctl -d ata -a /dev/sda
smartctl 5.40 2010-07-12 r3124 [i686-pc-linux-gnu] (local build)
Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Model Family: Fujitsu MHZ2 BH series
Device Model: FUJITSU MHZ2160BH G2
Serial Number: *************
Firmware Version: 00000009
User Capacity: 160,041,885,696 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 3f
Local Time is: Sun Jun 26 05:36:15 2011 IRDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 649) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 92) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 100 100 046 Pre-fail Always - 251055
2 Throughput_Performance 0x0005 100 100 030 Pre-fail Offline - 29425664
3 Spin_Up_Time 0x0003 100 100 025 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 3883
5 Reallocated_Sector_Ct 0x0033 100 100 024 Pre-fail Always - 0 (2000, 0)
7 Seek_Error_Rate 0x000f 100 100 047 Pre-fail Always - 1461
8 Seek_Time_Performance 0x0005 100 100 019 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 090 090 000 Old_age Always - 5065
10 Spin_Retry_Count 0x0013 100 100 020 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 3742
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 201
193 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 7401
194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 44 (Lifetime Min/Max 15/60)
195 Hardware_ECC_Recovered 0x001a 100 100 000 Old_age Always - 71
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 (0, 4809)
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 253 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x000f 100 100 060 Pre-fail Always - 32448
203 Run_Out_Cancel 0x0002 100 100 000 Old_age Always - 429510491997
240 Head_Flying_Hours 0x003e 200 200 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Conveyance offline Completed without error 00% 2306 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
smartctl 5.40 2010-03-16 r3077 [x86_64-unknown-linux-gnu] (local build)
Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Device Model: HITACHI HTS545032B9A300
Serial Number: 100417PBPC041DK0SD1M
Firmware Version: PB3ZC61H
User Capacity: 320,072,933,376 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 6
Local Time is: Sun Jun 26 14:01:53 2011 IRDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 645) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 106) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 062 Pre-fail Always - 0
2 Throughput_Performance 0x0005 100 100 040 Pre-fail Offline - 0
3 Spin_Up_Time 0x0007 141 141 033 Pre-fail Always - 2
4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 283
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 040 Pre-fail Offline - 0
9 Power_On_Hours 0x0012 092 092 000 Old_age Always - 3545
10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 280
191 G-Sense_Error_Rate 0x000a 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 17
193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 7051
194 Temperature_Celsius 0x0002 119 119 000 Old_age Always - 46 (Lifetime Min/Max 13/53)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0
223 Load_Retry_Count 0x000a 100 100 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Vendor offline Completed without error 00% 4 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
9 Power_On_Hours 0x0032 089 089 000 Old_age Always - 9804
12 Power_Cycle_Count 0x0032 099 099 020 Old_age Always - 1513
[ehsan@ehsan-EP45-UD3R ~]$ sudo smartctl -d ata -a /dev/sda
smartctl 5.40 2010-07-12 r3124 [x86_64-unknown-linux-gnu] (local build)
Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.12 family
Device Model: ST3500418AS
Serial Number: 6VM0FQBY
Firmware Version: CC34
User Capacity: 500,107,862,016 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 4
Local Time is: Sun Jun 26 15:03:14 2011 IRDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 600) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 94) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x103f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 117 099 006 Pre-fail Always - 118160589
3 Spin_Up_Time 0x0003 097 097 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 099 099 020 Old_age Always - 1510
5 Reallocated_Sector_Ct 0x0033 099 099 036 Pre-fail Always - 47
7 Seek_Error_Rate 0x000f 081 060 030 Pre-fail Always - 155177460
9 Power_On_Hours 0x0032 089 089 000 Old_age Always - 9804
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 099 099 020 Old_age Always - 1513
183 Runtime_Bad_Block 0x0000 100 100 000 Old_age Offline - 0
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0
188 Command_Timeout 0x0032 100 091 000 Old_age Always - 4295887747
189 High_Fly_Writes 0x003a 081 081 000 Old_age Always - 19
190 Airflow_Temperature_Cel 0x0022 057 051 045 Old_age Always - 43 (Lifetime Min/Max 28/43)
194 Temperature_Celsius 0x0022 043 049 000 Old_age Always - 43 (0 18 0 0)
195 Hardware_ECC_Recovered 0x001a 036 022 000 Old_age Always - 118160589
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
240 Head_Flying_Hours 0x0000 100 253 000 Old_age Offline - 86569360831758
241 Total_LBAs_Written 0x0000 100 253 000 Old_age Offline - 883813203
242 Total_LBAs_Read 0x0000 100 253 000 Old_age Offline - 2659564378
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
9 Power_On_Hours 0x0032 089 089 000 Old_age Always - 9804
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 099 099 020 Old_age Always - 1513اشتباه نوشتید اون ساعت کار کرد هستکد: [انتخاب]9 Power_On_Hours 0x0032 089 089 000 Old_age Always - 9804
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 099 099 020 Old_age Always - 1513
Load_Cycle_Count سایکل هست
sudo smartctl -d ata -a /dev/sdasmartctl 5.41 2011-06-09 r3365 [x86_64-linux-3.0.0-14-generic] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Model Family: Hitachi Travelstar 7K500
Device Model: Hitachi HTS725032A9A364
Serial Number: 101223PCK304GKHLWERK
LU WWN Device Id: 5 000cca 645d6ad33
Firmware Version: PC3OCH0A
User Capacity: 320,072,933,376 bytes [320 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: 8
ATA Standard is: ATA-8-ACS revision 6
Local Time is: Sat Jan 7 15:47:47 2012 IRST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 645) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 92) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 100 100 062 Pre-fail Always - 0
2 Throughput_Performance 0x0025 100 100 040 Pre-fail Offline - 0
3 Spin_Up_Time 0x0023 160 100 033 Pre-fail Always - 2
4 Start_Stop_Count 0x0032 099 099 000 Old_age Always - 1674
5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 8 (0, 2)
7 Seek_Error_Rate 0x002f 100 100 067 Pre-fail Always - 0
8 Seek_Time_Performance 0x0025 100 100 040 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 095 095 000 Old_age Always - 2484
10 Spin_Retry_Count 0x0033 100 100 060 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1654
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0
184 End-to-End_Error 0x0033 100 100 097 Pre-fail Always - 0
187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 12517376
188 Command_Timeout 0x0032 100 098 000 Old_age Always - 65538
190 Airflow_Temperature_Cel 0x0022 067 055 045 Old_age Always - 33 (Min/Max 21/33)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 10
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 6029404
193 Load_Cycle_Count 0x0032 099 099 000 Old_age Always - 16940
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 1
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0036 100 100 000 Old_age Always - 0
223 Load_Retry_Count 0x002a 100 098 000 Old_age Always - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 2455 -
# 2 Short offline Completed without error 00% 2453 -
# 3 Short offline Aborted by host 90% 2442 -
# 4 Short offline Completed without error 00% 2442 -
# 5 Short offline Completed without error 00% 2442 -
# 6 Short offline Completed without error 00% 2442 -
# 7 Short offline Completed without error 00% 2442 -
# 8 Short offline Completed without error 00% 2442 -
# 9 Short offline Completed without error 00% 2441 -
#10 Short offline Completed without error 00% 2441 -
#11 Short offline Completed without error 00% 2441 -
#12 Extended offline Completed without error 00% 2441 -
#13 Short offline Completed without error 00% 2440 -
#14 Short offline Completed without error 00% 2438 -
#15 Extended offline Completed without error 00% 1799 -
#16 Short offline Completed without error 00% 1798 -
#17 Extended offline Aborted by host 90% 1798 -
#18 Short offline Completed without error 00% 1798 -
#19 Short offline Completed without error 00% 1798 -
#20 Short offline Completed without error 00% 1798 -
#21 Short offline Completed without error 00% 1472 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
۵۰۰۰۰۰ تا شده و ۶ ماه نیست اومدم رو لینوکس ! و واقعا تعجب میکنم ! شاید بهتر باشه کمی مسولیت پذیر باشن ! یک چیزی که کیفیت محصولی که به دست من میرسه رو تضمین کنه ! من نمیخوام تو یه همچین وضعیت های ساده ای با این خزعولات ضرر بخورم ( ۲۰۰-۳۰۰ تومن مینیمم خرج این هارد مادر مردست -_- ) و باگ هایی مثل داغ کردن ( که باهاش درگیرم ... ) و ...
و واقعا اگر ویندوز پکیج منیجر مثل لینوکس داشت یه لحظه درنگ نمیکردم برای برگشتن -_-
هارد بیچاره اگه بدونی چه وضعی داره ...
کسی هست بیاد از فلسفه‌ی آزاد متن دفاع درخوری بکنه !
و به من بگه که دقیقا این وسط باگهایی که اینهمه مدت باز میمونن و حتی موقتا اون قسمت‌های سیستم غیر فعال نمیشه تا چنین اتفاقایی نیفته دقیقا مسولشون کیه !؟ اینی که برنامه‌ی آزاد تولید میکنن دلیلی به آزادیشون تو تولید یک سیستم بیکیفیت نیست -_-
gnome-disk-utilityکه همون برنامه Disks هست که پیشفرض نصب هست هم مانع انجام این کار بشید درایو انتخاب کنید و وارد تنظیماتش شید و مقدار مورد نظر APM AAM و تنظیمات ببخشید ... داغ کرده بودم :-(ویندوز هم تنظیمات مربوط به هاردیسک داره(معمولا در حالت power saving بیشترین کلیک رو داره مگر اینکه تنظیماتش رو عوض کرده باشین)
من یه چیزی یادم میاد یه نم شک دارم ...
من یادمه اول وقتی که باگ رو دیدم این LCC روی ۴۹۹۹۸ بود ( دستور "sudo smartctl -d ata -a /dev/sda" ) و شاید تو ۵ دقیقه هیچ تغییری نکرد ... ولی من گذاشتم به حساب مشکل تو لینوکس :-\ ممکنه مشکل از ویندوز باشه یعنی !؟ ( چون واقعا این رقم خیلی وحشتناکه ! با هیچ پروسه منطقی تو مدتی که لپ تاپو خریدم نمیشه بهش رسید ! )
جمعه ۱۸ ژوئیه ۱۴، ساعت ۲۱:۰۰:۰۱ (IRDT)
193 Load_Cycle_Count 0x0032 098 098 000 Old_age Always - 21015
==================================================
جمعه ۱۸ ژوئیه ۱۴، ساعت ۲۲:۰۰:۰۱ (IRDT)
193 Load_Cycle_Count 0x0032 098 098 000 Old_age Always - 21032
==================================================
جمعه ۱۸ ژوئیه ۱۴، ساعت ۲۳:۰۰:۰۱ (IRDT)
193 Load_Cycle_Count 0x0032 098 098 000 Old_age Always - 21043
==================================================
اطلاعاتم :سلام دوستان
من کل تاپیک رو از اول خوندم و برام جالب بود
این نتایج منه :کد: [انتخاب]جمعه ۱۸ ژوئیه ۱۴، ساعت ۲۱:۰۰:۰۱ (IRDT)اطلاعاتم :
193 Load_Cycle_Count 0x0032 098 098 000 Old_age Always - 21015
==================================================
جمعه ۱۸ ژوئیه ۱۴، ساعت ۲۲:۰۰:۰۱ (IRDT)
193 Load_Cycle_Count 0x0032 098 098 000 Old_age Always - 21032
==================================================
جمعه ۱۸ ژوئیه ۱۴، ساعت ۲۳:۰۰:۰۱ (IRDT)
193 Load_Cycle_Count 0x0032 098 098 000 Old_age Always - 21043
==================================================
Acer v3-571G
Hard Disk : TOSHIBA MQ01ABD075 (http://storage.toshiba.eu/cms/en/hdd/computing/product_detail.jsp?productid=409)
kubuntu 14.04
خوب حالا بعدا طبق چیزایی که دوستان در تاپیک گفتند عمل میکنم و سرعت اضافه شدنش رو کم میکنم ولی سوال اصلیم اینه (ببخشید سوال‌هام کلیه ولی هیچ سر رشته‌ای ندارم ) :
1.این سایکل چیه و چطوری اضافه میشه ؟
بر چه اساسی اضافه میشه ؟ ( یعنی توی عملیات‌هایی مثل بک آپ گرفتن هم زیاد میشه ؟)
2.این سایکل چه رابطه‌ای با عمر هارد بر حسب ساعت داره ؟
3.پارک کردن هد ( کلیک ؟ ) چیه و به چه منظور انجام میشه ؟ و آیا نرماله ؟
4.چطور میتونم بفهمم که عمر هاردم چقدر چقدره ؟ ( عمر هارد بر اساس سایکله یا ساعت ؟ )
*کلا اگه یکی یه توضیحی درباره‌ی این سایکل بده ممنون میشم
پیشاپیش تشکر
sudo smartctl -d ata -a /dev/sda
شماره ۹ عمر هارد رو نشون میده
۱.با هربار لود یا آنلود شدن هاردیسک یه دونه به این لایف سایکل اضافه میشه یعنی با یه بار روشن خاموش کردن حداقل ۲تا بهش اضافه میشه. برای کاهش مصرف انرژی در حین استفاده هم اگه هارد استفاده نشه ممکنه این اتفاق بیفته که میشه هم تو لینوکس هم تو ویندوز تنظیمش کرد.ممنون بابت توضیحاتتون
۲. معمولا هر هاردیسک حدود ۶۰۰ هزار تا لایف سایکل داره که اینو شرکت سازنده میگه چندتاست. البته حتما قرار نیست بعد این تعداد خراب بشه من ۲ میلیون هم دیدم که هنوز کار میکنه :D
۴. عمر هارد رو هم با این دستور میتونی ببینی:کد: [انتخاب]sudo smartctl -d ata -a /dev/sdaشماره ۹ عمر هارد رو نشون میده
9 Power_On_Hours 0x0032 093 093 000 Old_age Always - 3057=== START OF INFORMATION SECTION ===
Model Family: Toshiba 2.5" HDD MQ01ABD...
Device Model: TOSHIBA MQ01ABD075
Serial Number: 92K8P49XT
LU WWN Device Id: 5 000039 44250620e
Firmware Version: AX003J
User Capacity: 750,156,374,016 bytes [750 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Sat Jul 19 14:17:38 2014 IRDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 189) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0
3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 1743
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 6240
5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 093 093 000 Old_age Always - 3057
10 Spin_Retry_Count 0x0033 221 100 030 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 1976
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 31
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 140
193 Load_Cycle_Count 0x0032 098 098 000 Old_age Always - 21151
194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 43 (Min/Max 19/53)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
220 Disk_Shift 0x0002 100 100 000 Old_age Always - 0
222 Loaded_Hours 0x0032 095 095 000 Old_age Always - 2177
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0
224 Load_Friction 0x0022 100 100 000 Old_age Always - 0
226 Load-in_Time 0x0026 100 100 000 Old_age Always - 263
240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
193 Load_Cycle_Count 0x0032 001 001 000 Old_age Always - 283739smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.13.5-1-ARCH] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Momentus 5400.6
Device Model: ST9500325AS
Serial Number: 5VESDESB
LU WWN Device Id: 5 000c50 049879315
Firmware Version: 0003SDM1
User Capacity: 500,107,862,016 bytes [500 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Sat Jul 19 16:21:30 2014 IRDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 136) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x103b) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 117 099 006 Pre-fail Always - 124606883
3 Spin_Up_Time 0x0003 098 098 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 097 097 020 Old_age Always - 3628
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 1
7 Seek_Error_Rate 0x000f 078 060 030 Pre-fail Always - 71147795
9 Power_On_Hours 0x0032 093 093 000 Old_age Always - 6479
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 097 097 020 Old_age Always - 3542
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 096 096 000 Old_age Always - 4
188 Command_Timeout 0x0032 100 097 000 Old_age Always - 8590065772
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 058 054 045 Old_age Always - 42 (Min/Max 40/42)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 155
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 0
193 Load_Cycle_Count 0x0032 001 001 000 Old_age Always - 283739
194 Temperature_Celsius 0x0022 042 046 000 Old_age Always - 42 (0 16 0 0 0)
195 Hardware_ECC_Recovered 0x001a 051 045 000 Old_age Always - 124606883
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
254 Free_Fall_Sensor 0x0032 100 100 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 4
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 4 occurred at disk power-on lifetime: 2754 hours (114 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ff ff ff 4f 00 00:12:14.844 READ FPDMA QUEUED
27 00 00 00 00 00 e0 00 00:12:14.843 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 00:12:14.842 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:12:14.841 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 00:12:14.841 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 3 occurred at disk power-on lifetime: 2754 hours (114 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ff ff ff 4f 00 00:12:12.333 READ FPDMA QUEUED
61 00 10 ff ff ff 4f 00 00:12:12.333 WRITE FPDMA QUEUED
61 00 58 ff ff ff 4f 00 00:12:12.332 WRITE FPDMA QUEUED
27 00 00 00 00 00 e0 00 00:12:12.332 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 00:12:12.330 IDENTIFY DEVICE
Error 2 occurred at disk power-on lifetime: 2754 hours (114 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ff ff ff 4f 00 00:12:07.999 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 00:12:07.998 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 00:12:07.998 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 00:12:07.997 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 00:12:07.995 READ FPDMA QUEUED
Error 1 occurred at disk power-on lifetime: 2749 hours (114 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ff ff ff 4f 00 06:19:51.573 READ FPDMA QUEUED
60 00 28 ff ff ff 4f 00 06:19:50.391 READ FPDMA QUEUED
60 00 28 ff ff ff 4f 00 06:19:47.914 READ FPDMA QUEUED
61 00 08 ff ff ff 4f 00 06:19:47.727 WRITE FPDMA QUEUED
61 00 08 ff ff ff 4f 00 06:19:47.727 WRITE FPDMA QUEUED
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 6477 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
sudo smartctl -d ata -a /dev/sda | grep Load_Cycle && sleep 600 && sudo smartctl -d ata -a /dev/sda | grep Load_Cycle && sleep 600 && sudo smartctl -d ata -a /dev/sda | grep Load_Cycle
193 Load_Cycle_Count 0x0012 085 085 000 Old_age Always - 159039
193 Load_Cycle_Count 0x0012 085 085 000 Old_age Always - 159039
193 Load_Cycle_Count 0x0012 085 085 000 Old_age Always - 159039چرا؟ 150هزار شده ولی تو نیم ساعت هیچی؟سلام دوستان
من کل تاپیک رو از اول خوندم و برام جالب بود
این نتایج منه :کد: [انتخاب]جمعه ۱۸ ژوئیه ۱۴، ساعت ۲۱:۰۰:۰۱ (IRDT)اطلاعاتم :
193 Load_Cycle_Count 0x0032 098 098 000 Old_age Always - 21015
==================================================
جمعه ۱۸ ژوئیه ۱۴، ساعت ۲۲:۰۰:۰۱ (IRDT)
193 Load_Cycle_Count 0x0032 098 098 000 Old_age Always - 21032
==================================================
جمعه ۱۸ ژوئیه ۱۴، ساعت ۲۳:۰۰:۰۱ (IRDT)
193 Load_Cycle_Count 0x0032 098 098 000 Old_age Always - 21043
==================================================
Acer v3-571G
Hard Disk : TOSHIBA MQ01ABD075 (http://storage.toshiba.eu/cms/en/hdd/computing/product_detail.jsp?productid=409)
kubuntu 14.04
خوب حالا بعدا طبق چیزایی که دوستان در تاپیک گفتند عمل میکنم و سرعت اضافه شدنش رو کم میکنم ولی سوال اصلیم اینه (ببخشید سوال‌هام کلیه ولی هیچ سر رشته‌ای ندارم ) :
1.این سایکل چیه و چطوری اضافه میشه ؟
بر چه اساسی اضافه میشه ؟ ( یعنی توی عملیات‌هایی مثل بک آپ گرفتن هم زیاد میشه ؟)
2.این سایکل چه رابطه‌ای با عمر هارد بر حسب ساعت داره ؟
3.پارک کردن هد ( کلیک ؟ ) چیه و به چه منظور انجام میشه ؟ و آیا نرماله ؟
4.چطور میتونم بفهمم که عمر هاردم چقدر چقدره ؟ ( عمر هارد بر اساس سایکله یا ساعت ؟ )
*کلا اگه یکی یه توضیحی درباره‌ی این سایکل بده ممنون میشم
پیشاپیش تشکر
۱.با هربار لود یا آنلود شدن هاردیسک یه دونه به این لایف سایکل اضافه میشه یعنی با یه بار روشن خاموش کردن حداقل ۲تا بهش اضافه میشه. برای کاهش مصرف انرژی در حین استفاده هم اگه هارد استفاده نشه ممکنه این اتفاق بیفته که میشه هم تو لینوکس هم تو ویندوز تنظیمش کرد.
۲. معمولا هر هاردیسک حدود ۶۰۰ هزار تا لایف سایکل داره که اینو شرکت سازنده میگه چندتاست. البته حتما قرار نیست بعد این تعداد خراب بشه من ۲ میلیون هم دیدم که هنوز کار میکنه :D
۴. عمر هارد رو هم با این دستور میتونی ببینی:کد: [انتخاب]sudo smartctl -d ata -a /dev/sdaشماره ۹ عمر هارد رو نشون میده
=== START OF INFORMATION SECTION ===
Model Family: Toshiba 2.5" HDD MQ01ABD...
Device Model: TOSHIBA MQ01ABD100
Serial Number: 3314CENXT
LU WWN Device Id: 5 000039 4a3480340
Firmware Version: AX001A
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 3.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Sat Jul 19 20:48:28 2014 IRDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 240) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0
3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 1705
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 516
5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 098 098 000 Old_age Always - 1195
10 Spin_Retry_Count 0x0033 110 100 030 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 514
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 108
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 28
193 Load_Cycle_Count 0x0032 099 099 000 Old_age Always - 11656
194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 45 (Min/Max 9/55)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
220 Disk_Shift 0x0002 100 100 000 Old_age Always - 0
222 Loaded_Hours 0x0032 098 098 000 Old_age Always - 1109
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0
224 Load_Friction 0x0022 100 100 000 Old_age Always - 0
226 Load-in_Time 0x0026 100 100 000 Old_age Always - 191
240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 1141 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
۱.با هربار لود یا آنلود شدن هاردیسک یه دونه به این لایف سایکل اضافه میشه یعنی با یه بار روشن خاموش کردن حداقل ۲تا بهش اضافه میشه. برای کاهش مصرف انرژی در حین استفاده هم اگه هارد استفاده نشه ممکنه این اتفاق بیفته که میشه هم تو لینوکس هم تو ویندوز تنظیمش کرد.ممنون بابت توضیحاتتون
۲. معمولا هر هاردیسک حدود ۶۰۰ هزار تا لایف سایکل داره که اینو شرکت سازنده میگه چندتاست. البته حتما قرار نیست بعد این تعداد خراب بشه من ۲ میلیون هم دیدم که هنوز کار میکنه :D
۴. عمر هارد رو هم با این دستور میتونی ببینی:کد: [انتخاب]sudo smartctl -d ata -a /dev/sdaشماره ۹ عمر هارد رو نشون میده
خوب ظاهرا برای من شماره‌ی ۹ نیست :کد: [انتخاب]9 Power_On_Hours 0x0032 093 093 000 Old_age Always - 3057
اینم نتیجه‌ی کامل :کد: [انتخاب]=== START OF INFORMATION SECTION ===
Model Family: Toshiba 2.5" HDD MQ01ABD...
Device Model: TOSHIBA MQ01ABD075
Serial Number: 92K8P49XT
LU WWN Device Id: 5 000039 44250620e
Firmware Version: AX003J
User Capacity: 750,156,374,016 bytes [750 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Sat Jul 19 14:17:38 2014 IRDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 189) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0
3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 1743
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 6240
5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 093 093 000 Old_age Always - 3057
10 Spin_Retry_Count 0x0033 221 100 030 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 1976
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 31
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 140
193 Load_Cycle_Count 0x0032 098 098 000 Old_age Always - 21151
194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 43 (Min/Max 19/53)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
220 Disk_Shift 0x0002 100 100 000 Old_age Always - 0
222 Loaded_Hours 0x0032 095 095 000 Old_age Always - 2177
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0
224 Load_Friction 0x0022 100 100 000 Old_age Always - 0
226 Load-in_Time 0x0026 100 100 000 Old_age Always - 263
240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
آقا این موضوع رو من تازه فهمیدم ولی انگاری یه کم دیر شده و هاردم به فنا رفته:کد: [انتخاب]193 Load_Cycle_Count 0x0032 001 001 000 Old_age Always - 283739
برای دو سال زیاده؟
در ضمن یه سری ارور هم توی خروجی smartctl هست:کد: [انتخاب]smartctl 6.2 2013-07-26 r3841 [x86_64-linux-3.13.5-1-ARCH] (local build)
Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Momentus 5400.6
Device Model: ST9500325AS
Serial Number: 5VESDESB
LU WWN Device Id: 5 000c50 049879315
Firmware Version: 0003SDM1
User Capacity: 500,107,862,016 bytes [500 GB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS T13/1699-D revision 4
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Sat Jul 19 16:21:30 2014 IRDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 0) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 136) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x103b) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 117 099 006 Pre-fail Always - 124606883
3 Spin_Up_Time 0x0003 098 098 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 097 097 020 Old_age Always - 3628
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 1
7 Seek_Error_Rate 0x000f 078 060 030 Pre-fail Always - 71147795
9 Power_On_Hours 0x0032 093 093 000 Old_age Always - 6479
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 097 097 020 Old_age Always - 3542
184 End-to-End_Error 0x0032 100 100 099 Old_age Always - 0
187 Reported_Uncorrect 0x0032 096 096 000 Old_age Always - 4
188 Command_Timeout 0x0032 100 097 000 Old_age Always - 8590065772
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 058 054 045 Old_age Always - 42 (Min/Max 40/42)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 155
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 0
193 Load_Cycle_Count 0x0032 001 001 000 Old_age Always - 283739
194 Temperature_Celsius 0x0022 042 046 000 Old_age Always - 42 (0 16 0 0 0)
195 Hardware_ECC_Recovered 0x001a 051 045 000 Old_age Always - 124606883
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
254 Free_Fall_Sensor 0x0032 100 100 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 4
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 4 occurred at disk power-on lifetime: 2754 hours (114 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ff ff ff 4f 00 00:12:14.844 READ FPDMA QUEUED
27 00 00 00 00 00 e0 00 00:12:14.843 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 00:12:14.842 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 00:12:14.841 SET FEATURES [Set transfer mode]
27 00 00 00 00 00 e0 00 00:12:14.841 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
Error 3 occurred at disk power-on lifetime: 2754 hours (114 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ff ff ff 4f 00 00:12:12.333 READ FPDMA QUEUED
61 00 10 ff ff ff 4f 00 00:12:12.333 WRITE FPDMA QUEUED
61 00 58 ff ff ff 4f 00 00:12:12.332 WRITE FPDMA QUEUED
27 00 00 00 00 00 e0 00 00:12:12.332 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3]
ec 00 00 00 00 00 a0 00 00:12:12.330 IDENTIFY DEVICE
Error 2 occurred at disk power-on lifetime: 2754 hours (114 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ff ff ff 4f 00 00:12:07.999 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 00:12:07.998 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 00:12:07.998 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 00:12:07.997 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 00:12:07.995 READ FPDMA QUEUED
Error 1 occurred at disk power-on lifetime: 2749 hours (114 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
60 00 08 ff ff ff 4f 00 06:19:51.573 READ FPDMA QUEUED
60 00 28 ff ff ff 4f 00 06:19:50.391 READ FPDMA QUEUED
60 00 28 ff ff ff 4f 00 06:19:47.914 READ FPDMA QUEUED
61 00 08 ff ff ff 4f 00 06:19:47.727 WRITE FPDMA QUEUED
61 00 08 ff ff ff 4f 00 06:19:47.727 WRITE FPDMA QUEUED
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 6477 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
چیز مهمیه؟
سلام.
دستور و خروجی را ببینید:کد: [انتخاب]sudo smartctl -d ata -a /dev/sda | grep Load_Cycle && sleep 600 && sudo smartctl -d ata -a /dev/sda | grep Load_Cycle && sleep 600 && sudo smartctl -d ata -a /dev/sda | grep Load_Cycleچرا؟ 150هزار شده ولی تو نیم ساعت هیچی؟
193 Load_Cycle_Count 0x0012 085 085 000 Old_age Always - 159039
193 Load_Cycle_Count 0x0012 085 085 000 Old_age Always - 159039
193 Load_Cycle_Count 0x0012 085 085 000 Old_age Always - 159039
من دو سال و نیم هست که لپتاپ را دارم و حدود یک سال ویندوز 7 داشتم و یک سال و نیم اوبونتو و گاهی ویندوز 7.
این 150هزار هم خیلی زیاده. یعنی اگه اینجوری بره سه‌چار سال دیگه احتمالا هارد خراب بشه.
یکی که فهمید چی میگم لطف کنه یه توضیحی راجع به روند اتقاقات بگه و بگه لازم هست کاری بکنم؟ راحت‌ترین راه چیه؟
منظور از تق‌تق هارد را نمی‌دونم ولی وقتی چیزی رونوشت میکنم یا از نت دریافت میکنم خیلی لپتاپ صدا میده و این فکر کنم cpu هست نه هارد.
acer aspire 5750g | Hitachi HTS547550A9E384 (JE3OA60A)
سلام دوستان
من کل تاپیک رو از اول خوندم و برام جالب بود
این نتایج منه :کد: [انتخاب]جمعه ۱۸ ژوئیه ۱۴، ساعت ۲۱:۰۰:۰۱ (IRDT)اطلاعاتم :
193 Load_Cycle_Count 0x0032 098 098 000 Old_age Always - 21015
==================================================
جمعه ۱۸ ژوئیه ۱۴، ساعت ۲۲:۰۰:۰۱ (IRDT)
193 Load_Cycle_Count 0x0032 098 098 000 Old_age Always - 21032
==================================================
جمعه ۱۸ ژوئیه ۱۴، ساعت ۲۳:۰۰:۰۱ (IRDT)
193 Load_Cycle_Count 0x0032 098 098 000 Old_age Always - 21043
==================================================
Acer v3-571G
Hard Disk : TOSHIBA MQ01ABD075 (http://storage.toshiba.eu/cms/en/hdd/computing/product_detail.jsp?productid=409)
kubuntu 14.04
خوب حالا بعدا طبق چیزایی که دوستان در تاپیک گفتند عمل میکنم و سرعت اضافه شدنش رو کم میکنم ولی سوال اصلیم اینه (ببخشید سوال‌هام کلیه ولی هیچ سر رشته‌ای ندارم ) :
1.این سایکل چیه و چطوری اضافه میشه ؟
بر چه اساسی اضافه میشه ؟ ( یعنی توی عملیات‌هایی مثل بک آپ گرفتن هم زیاد میشه ؟)
2.این سایکل چه رابطه‌ای با عمر هارد بر حسب ساعت داره ؟
3.پارک کردن هد ( کلیک ؟ ) چیه و به چه منظور انجام میشه ؟ و آیا نرماله ؟
4.چطور میتونم بفهمم که عمر هاردم چقدر چقدره ؟ ( عمر هارد بر اساس سایکله یا ساعت ؟ )
*کلا اگه یکی یه توضیحی درباره‌ی این سایکل بده ممنون میشم
پیشاپیش تشکر
۱.با هربار لود یا آنلود شدن هاردیسک یه دونه به این لایف سایکل اضافه میشه یعنی با یه بار روشن خاموش کردن حداقل ۲تا بهش اضافه میشه. برای کاهش مصرف انرژی در حین استفاده هم اگه هارد استفاده نشه ممکنه این اتفاق بیفته که میشه هم تو لینوکس هم تو ویندوز تنظیمش کرد.
۲. معمولا هر هاردیسک حدود ۶۰۰ هزار تا لایف سایکل داره که اینو شرکت سازنده میگه چندتاست. البته حتما قرار نیست بعد این تعداد خراب بشه من ۲ میلیون هم دیدم که هنوز کار میکنه :D
۴. عمر هارد رو هم با این دستور میتونی ببینی:کد: [انتخاب]sudo smartctl -d ata -a /dev/sdaشماره ۹ عمر هارد رو نشون میده
سلام اینم اطلاعات همون دستوری که گفته بودید سیستممو 3 سال دارم ولی نزدیک 6-7 ماهه که هاردمو عوض کردم.الان هاردم حالش خوبه یا نه؟کد: [انتخاب]=== START OF INFORMATION SECTION ===
Model Family: Toshiba 2.5" HDD MQ01ABD...
Device Model: TOSHIBA MQ01ABD100
Serial Number: 3314CENXT
LU WWN Device Id: 5 000039 4a3480340
Firmware Version: AX001A
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 3.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Sat Jul 19 20:48:28 2014 IRDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 240) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0
3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 1705
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 516
5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 098 098 000 Old_age Always - 1195
10 Spin_Retry_Count 0x0033 110 100 030 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 514
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 108
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 28
193 Load_Cycle_Count 0x0032 099 099 000 Old_age Always - 11656
194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 45 (Min/Max 9/55)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
220 Disk_Shift 0x0002 100 100 000 Old_age Always - 0
222 Loaded_Hours 0x0032 098 098 000 Old_age Always - 1109
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0
224 Load_Friction 0x0022 100 100 000 Old_age Always - 0
226 Load-in_Time 0x0026 100 100 000 Old_age Always - 191
240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 1141 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
sudo add-apt-repository ppa:linrunner/tlp
sudo apt-get update
sudo apt-get install tlp tlp-rdw
sudo gedit /etc/default/tlpDISK_APM_LEVEL_ON_AC="254 254"
DISK_APM_LEVEL_ON_BAT="254 254"چندبار دیگه امتحان کردم. در 24 ساعت برای هارد لپتاپ من حتی 500 تا هم بیشتر اضافه میشه یعنی یه حساب کردم دیدم توانش را داره 1000 تا هم زیاد بشه و این وحشتناکه.
فعلا از برنامه‌ی disks گزینه drive setting مقدار apm را فعال کردم و گذاشتم 255 ببینم چی میشه؟
یا کار دیگه‌ای بهتره انجام بدم.
راه‌های قبلی مال هفت سال پیشن و ترسیدم امتحان کنم (اون ساخت شل و ...)
سلام دوستان
من کل تاپیک رو از اول خوندم و برام جالب بود
این نتایج منه :کد: [انتخاب]جمعه ۱۸ ژوئیه ۱۴، ساعت ۲۱:۰۰:۰۱ (IRDT)اطلاعاتم :
193 Load_Cycle_Count 0x0032 098 098 000 Old_age Always - 21015
==================================================
جمعه ۱۸ ژوئیه ۱۴، ساعت ۲۲:۰۰:۰۱ (IRDT)
193 Load_Cycle_Count 0x0032 098 098 000 Old_age Always - 21032
==================================================
جمعه ۱۸ ژوئیه ۱۴، ساعت ۲۳:۰۰:۰۱ (IRDT)
193 Load_Cycle_Count 0x0032 098 098 000 Old_age Always - 21043
==================================================
Acer v3-571G
Hard Disk : TOSHIBA MQ01ABD075 (http://storage.toshiba.eu/cms/en/hdd/computing/product_detail.jsp?productid=409)
kubuntu 14.04
خوب حالا بعدا طبق چیزایی که دوستان در تاپیک گفتند عمل میکنم و سرعت اضافه شدنش رو کم میکنم ولی سوال اصلیم اینه (ببخشید سوال‌هام کلیه ولی هیچ سر رشته‌ای ندارم ) :
1.این سایکل چیه و چطوری اضافه میشه ؟
بر چه اساسی اضافه میشه ؟ ( یعنی توی عملیات‌هایی مثل بک آپ گرفتن هم زیاد میشه ؟)
2.این سایکل چه رابطه‌ای با عمر هارد بر حسب ساعت داره ؟
3.پارک کردن هد ( کلیک ؟ ) چیه و به چه منظور انجام میشه ؟ و آیا نرماله ؟
4.چطور میتونم بفهمم که عمر هاردم چقدر چقدره ؟ ( عمر هارد بر اساس سایکله یا ساعت ؟ )
*کلا اگه یکی یه توضیحی درباره‌ی این سایکل بده ممنون میشم
پیشاپیش تشکر
۱.با هربار لود یا آنلود شدن هاردیسک یه دونه به این لایف سایکل اضافه میشه یعنی با یه بار روشن خاموش کردن حداقل ۲تا بهش اضافه میشه. برای کاهش مصرف انرژی در حین استفاده هم اگه هارد استفاده نشه ممکنه این اتفاق بیفته که میشه هم تو لینوکس هم تو ویندوز تنظیمش کرد.
۲. معمولا هر هاردیسک حدود ۶۰۰ هزار تا لایف سایکل داره که اینو شرکت سازنده میگه چندتاست. البته حتما قرار نیست بعد این تعداد خراب بشه من ۲ میلیون هم دیدم که هنوز کار میکنه :D
۴. عمر هارد رو هم با این دستور میتونی ببینی:کد: [انتخاب]sudo smartctl -d ata -a /dev/sdaشماره ۹ عمر هارد رو نشون میده
سلام اینم اطلاعات همون دستوری که گفته بودید سیستممو 3 سال دارم ولی نزدیک 6-7 ماهه که هاردمو عوض کردم.الان هاردم حالش خوبه یا نه؟کد: [انتخاب]=== START OF INFORMATION SECTION ===
Model Family: Toshiba 2.5" HDD MQ01ABD...
Device Model: TOSHIBA MQ01ABD100
Serial Number: 3314CENXT
LU WWN Device Id: 5 000039 4a3480340
Firmware Version: AX001A
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 3.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Sat Jul 19 20:48:28 2014 IRDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 240) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0
3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 1705
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 516
5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 098 098 000 Old_age Always - 1195
10 Spin_Retry_Count 0x0033 110 100 030 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 514
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 108
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 28
193 Load_Cycle_Count 0x0032 099 099 000 Old_age Always - 11656
194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 45 (Min/Max 9/55)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
220 Disk_Shift 0x0002 100 100 000 Old_age Always - 0
222 Loaded_Hours 0x0032 098 098 000 Old_age Always - 1109
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0
224 Load_Friction 0x0022 100 100 000 Old_age Always - 0
226 Load-in_Time 0x0026 100 100 000 Old_age Always - 191
240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 1141 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
حدود ۱۰ تا برا هر ساعت پس خوبه!(تا ۴۰ تقریبا عادیه) البته میشه کمتر از این هم بشه.
منبع معتبر برای تعداد سیکل های هارد عمر یک هارد را لطفا قرار بدهیدمن hitachi دارم منبع معتبر سایتش http://www.hgst.com/ (http://www.hgst.com/) برا هر هاردیسک data sheet داره. نوشته ۶۰۰ هزار تا.
من چیزی در مورد هارد توشیبا پیدا نکردم
اکنون ۳۰ هزار تا مصرف کردم ، یعنی عمرش نصف شده؟
سلام دوستان
من کل تاپیک رو از اول خوندم و برام جالب بود
این نتایج منه :کد: [انتخاب]جمعه ۱۸ ژوئیه ۱۴، ساعت ۲۱:۰۰:۰۱ (IRDT)اطلاعاتم :
193 Load_Cycle_Count 0x0032 098 098 000 Old_age Always - 21015
==================================================
جمعه ۱۸ ژوئیه ۱۴، ساعت ۲۲:۰۰:۰۱ (IRDT)
193 Load_Cycle_Count 0x0032 098 098 000 Old_age Always - 21032
==================================================
جمعه ۱۸ ژوئیه ۱۴، ساعت ۲۳:۰۰:۰۱ (IRDT)
193 Load_Cycle_Count 0x0032 098 098 000 Old_age Always - 21043
==================================================
Acer v3-571G
Hard Disk : TOSHIBA MQ01ABD075 (http://storage.toshiba.eu/cms/en/hdd/computing/product_detail.jsp?productid=409)
kubuntu 14.04
خوب حالا بعدا طبق چیزایی که دوستان در تاپیک گفتند عمل میکنم و سرعت اضافه شدنش رو کم میکنم ولی سوال اصلیم اینه (ببخشید سوال‌هام کلیه ولی هیچ سر رشته‌ای ندارم ) :
1.این سایکل چیه و چطوری اضافه میشه ؟
بر چه اساسی اضافه میشه ؟ ( یعنی توی عملیات‌هایی مثل بک آپ گرفتن هم زیاد میشه ؟)
2.این سایکل چه رابطه‌ای با عمر هارد بر حسب ساعت داره ؟
3.پارک کردن هد ( کلیک ؟ ) چیه و به چه منظور انجام میشه ؟ و آیا نرماله ؟
4.چطور میتونم بفهمم که عمر هاردم چقدر چقدره ؟ ( عمر هارد بر اساس سایکله یا ساعت ؟ )
*کلا اگه یکی یه توضیحی درباره‌ی این سایکل بده ممنون میشم
پیشاپیش تشکر
۱.با هربار لود یا آنلود شدن هاردیسک یه دونه به این لایف سایکل اضافه میشه یعنی با یه بار روشن خاموش کردن حداقل ۲تا بهش اضافه میشه. برای کاهش مصرف انرژی در حین استفاده هم اگه هارد استفاده نشه ممکنه این اتفاق بیفته که میشه هم تو لینوکس هم تو ویندوز تنظیمش کرد.
۲. معمولا هر هاردیسک حدود ۶۰۰ هزار تا لایف سایکل داره که اینو شرکت سازنده میگه چندتاست. البته حتما قرار نیست بعد این تعداد خراب بشه من ۲ میلیون هم دیدم که هنوز کار میکنه :D
۴. عمر هارد رو هم با این دستور میتونی ببینی:کد: [انتخاب]sudo smartctl -d ata -a /dev/sdaشماره ۹ عمر هارد رو نشون میده
سلام اینم اطلاعات همون دستوری که گفته بودید سیستممو 3 سال دارم ولی نزدیک 6-7 ماهه که هاردمو عوض کردم.الان هاردم حالش خوبه یا نه؟کد: [انتخاب]=== START OF INFORMATION SECTION ===
Model Family: Toshiba 2.5" HDD MQ01ABD...
Device Model: TOSHIBA MQ01ABD100
Serial Number: 3314CENXT
LU WWN Device Id: 5 000039 4a3480340
Firmware Version: AX001A
User Capacity: 1,000,204,886,016 bytes [1.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 3.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Sat Jul 19 20:48:28 2014 IRDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 240) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0
3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 1705
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 516
5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always - 0
7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 098 098 000 Old_age Always - 1195
10 Spin_Retry_Count 0x0033 110 100 030 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 514
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 108
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 28
193 Load_Cycle_Count 0x0032 099 099 000 Old_age Always - 11656
194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 45 (Min/Max 9/55)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
220 Disk_Shift 0x0002 100 100 000 Old_age Always - 0
222 Loaded_Hours 0x0032 098 098 000 Old_age Always - 1109
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0
224 Load_Friction 0x0022 100 100 000 Old_age Always - 0
226 Load-in_Time 0x0026 100 100 000 Old_age Always - 191
240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 1141 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
حدود ۱۰ تا برا هر ساعت پس خوبه!(تا ۴۰ تقریبا عادیه) البته میشه کمتر از این هم بشه.
سلام ممکنه بگید کدوم پارامتر هارو محاسبه کردید و به این نتیجه رسیدید؟
دوستان تو ورژن های جدیدتر اوبونتو مثل ۱۴.۰۴ این مشکل برطرف شده یا هنوز موجوده ؟این مشکل نیست! توی لپ تاپ ها برای این که مصرف کم بشه این ویژگی وجود داره. توی ویندوز هم این ویژگی وجود داره.
با تشکر از دوستان نتیجه برای من 9 بار در ساعته. این عدد خوبه یا بد. میشه از این کمتر بشه؟ با چه دستور یا نرم افزاری این کار انجام میشه. اینم نتیجه کلی:معمولا هارددیسک ها متوسط ۶۰۰ هزار لود سایکل عمر دارن( البته ممکنه تا چند میلیون هم عمر کنن)
9 Power_On_Hours 0x0012 086 086 000 Old_age Always - 6461
12 Power_Cycle_Count 0x0032 098 098 000 Old_age Always - 3964
193 Load_Cycle_Count 0x0012 095 095 000 Old_age Always - 54909
APM رو تو Drive Setting به سمت perform better بردم.(255 Disable) زمان استندبای رو هم بیشتر کردم. مصرف انرژی اصلا واسم مهم نیست. این تنظیم خوبه یا بد؟
وظعیت این هارد چطور است؟هنوز خیلی جا داره. ۳۰ برابر این قدری که تا الآن کار کرده میتونه کار کنه
Power_On_Hours 0x0032 095 095 000 Old_age Always - 4818
Power_Cycle_Count 0x0032 097 097 020 Old_age Always - 3091
Load_Cycle_Count 0x0032 090 090 000 Old_age Always - 21282
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Scorpio Black (AF)
Device Model: WDC WD7500BPKT-75PK4T0
Serial Number: WD-WXG1EB0DRZ22
LU WWN Device Id: 5 0014ee 25aca1420
Firmware Version: 01.01A01
User Capacity: 750,156,374,016 bytes [750 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Sun May 10 15:29:15 2015 IRDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x02) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (12300) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 122) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x7035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 190 168 021 Pre-fail Always - 1500
4 Start_Stop_Count 0x0032 096 096 000 Old_age Always - 4407
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 082 082 000 Old_age Always - 13170
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 097 097 000 Old_age Always - 3723
191 G-Sense_Error_Rate 0x0032 001 001 000 Old_age Always - 33408
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 541
193 Load_Cycle_Count 0x0032 121 121 000 Old_age Always - 239020
194 Temperature_Celsius 0x0022 101 083 000 Old_age Always - 46
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0
240 Head_Flying_Hours 0x0032 085 085 000 Old_age Always - 11581
241 Total_LBAs_Written 0x0032 200 200 000 Old_age Always - 66528129775
242 Total_LBAs_Read 0x0032 200 200 000 Old_age Always - 68275380701
254 Free_Fall_Sensor 0x0032 001 001 000 Old_age Always - 835
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Interrupted (host reset) 80% 6132 -
# 2 Short offline Completed without error 00% 5636 -
# 3 Short offline Completed without error 00% 0 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.دوستان نظری هم راجع به مشخصات هارد من لطف میکنید؟کد: [انتخاب]=== START OF INFORMATION SECTION ===.
Model Family: Western Digital Scorpio Black (AF)
Device Model: WDC WD7500BPKT-75PK4T0
Serial Number: WD-WXG1EB0DRZ22
LU WWN Device Id: 5 0014ee 25aca1420
Firmware Version: 01.01A01
User Capacity: 750,156,374,016 bytes [750 GB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 3.0 Gb/s
Local Time is: Sun May 10 15:29:15 2015 IRDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x02) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (12300) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 122) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x7035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 190 168 021 Pre-fail Always - 1500
4 Start_Stop_Count 0x0032 096 096 000 Old_age Always - 4407
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 082 082 000 Old_age Always - 13170
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 097 097 000 Old_age Always - 3723
191 G-Sense_Error_Rate 0x0032 001 001 000 Old_age Always - 33408
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 541
193 Load_Cycle_Count 0x0032 121 121 000 Old_age Always - 239020
194 Temperature_Celsius 0x0022 101 083 000 Old_age Always - 46
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0
240 Head_Flying_Hours 0x0032 085 085 000 Old_age Always - 11581
241 Total_LBAs_Written 0x0032 200 200 000 Old_age Always - 66528129775
242 Total_LBAs_Read 0x0032 200 200 000 Old_age Always - 68275380701
254 Free_Fall_Sensor 0x0032 001 001 000 Old_age Always - 835
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Interrupted (host reset) 80% 6132 -
# 2 Short offline Completed without error 00% 5636 -
# 3 Short offline Completed without error 00% 0 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay
=== START OF INFORMATION SECTION ===
Model Family: Toshiba 2.5" HDD MK..52GSX
Device Model: TOSHIBA MK3252GSX
Serial Number: 987BC5SHT
LU WWN Device Id: 5 000039 143801654
Firmware Version: LV010M
User Capacity: 320,072,933,376 bytes [320 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 1.5 Gb/s
Local Time is: Sun May 10 20:41:57 2015 IRDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 135) minutes.
SCT capabilities: (0x0039) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0
3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 1605
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 5250
5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always - 11
7 Seek_Error_Rate 0x000b 100 099 050 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 094 094 000 Old_age Always - 2706
10 Spin_Retry_Count 0x0033 204 100 030 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 4276
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 793
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 28049575
193 Load_Cycle_Count 0x0032 095 095 000 Old_age Always - 56476
194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 43 (Min/Max 12/57)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 11
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
220 Disk_Shift 0x0002 100 100 000 Old_age Always - 8324
222 Loaded_Hours 0x0032 096 096 000 Old_age Always - 1832
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0
224 Load_Friction 0x0022 100 100 000 Old_age Always - 0
226 Load-in_Time 0x0026 100 100 000 Old_age Always - 259
240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0
SMART Error Log Version: 1
ATA Error Count: 2
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 2 occurred at disk power-on lifetime: 2695 hours (112 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 01 d7 5a 71 e0 Error: ICRC, ABRT 1 sectors at LBA = 0x00715ad7 = 7428823
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
35 00 a8 30 57 71 e0 00 01:05:04.969 WRITE DMA EXT
35 00 40 f0 53 71 e0 00 01:05:04.958 WRITE DMA EXT
35 00 20 d0 50 71 e0 00 01:05:04.949 WRITE DMA EXT
35 00 00 d0 4c 71 e0 00 01:05:04.936 WRITE DMA EXT
35 00 00 d0 48 71 e0 00 01:05:04.923 WRITE DMA EXT
Error 1 occurred at disk power-on lifetime: 2552 hours (106 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 01 7f 45 00 e0 Error: ICRC, ABRT 1 sectors at LBA = 0x0000457f = 17791
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
35 00 60 20 44 00 e0 00 00:00:47.023 WRITE DMA EXT
ca 00 08 d0 43 00 e4 00 00:00:47.018 WRITE DMA
ca 00 20 40 42 00 e4 00 00:00:47.017 WRITE DMA
ca 00 78 c0 41 00 e4 00 00:00:47.017 WRITE DMA
ca 00 08 a0 41 00 e4 00 00:00:47.013 WRITE DMA
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 2526 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
سلامعدد مقابل گزینه شماره ۱۹۳ و ۹. شماره ۹ میزان ساعت کارکرد هاردتون هستش(مال شما ۲۷۰۶ ساعت). شماره ۱۹۳ تعداد دفعاتی که هارتون لود شده(مال شما 56476). اگه به هم تقسیم کنیم حدود ۲۰ میاد که نرمال هستش البته میتونید با تنظیمات کمتر کنید. به طور متوسط ۶۰۰هزار بار هارد میتونه خاموش/روشن بشه. البته من چند میلیونی هم دیدم :Dکد: [انتخاب]=== START OF INFORMATION SECTION ===
Model Family: Toshiba 2.5" HDD MK..52GSX
Device Model: TOSHIBA MK3252GSX
Serial Number: 987BC5SHT
LU WWN Device Id: 5 000039 143801654
Firmware Version: LV010M
User Capacity: 320,072,933,376 bytes [320 GB]
Sector Size: 512 bytes logical/physical
Device is: In smartctl database [for details use: -P show]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 2.6, 1.5 Gb/s
Local Time is: Sun May 10 20:41:57 2015 IRDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 135) minutes.
SCT capabilities: (0x0039) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail Always - 0
2 Throughput_Performance 0x0005 100 100 050 Pre-fail Offline - 0
3 Spin_Up_Time 0x0027 100 100 001 Pre-fail Always - 1605
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 5250
5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail Always - 11
7 Seek_Error_Rate 0x000b 100 099 050 Pre-fail Always - 0
8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail Offline - 0
9 Power_On_Hours 0x0032 094 094 000 Old_age Always - 2706
10 Spin_Retry_Count 0x0033 204 100 030 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 4276
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 793
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 28049575
193 Load_Cycle_Count 0x0032 095 095 000 Old_age Always - 56476
194 Temperature_Celsius 0x0022 100 100 000 Old_age Always - 43 (Min/Max 12/57)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 11
197 Current_Pending_Sector 0x0032 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
220 Disk_Shift 0x0002 100 100 000 Old_age Always - 8324
222 Loaded_Hours 0x0032 096 096 000 Old_age Always - 1832
223 Load_Retry_Count 0x0032 100 100 000 Old_age Always - 0
224 Load_Friction 0x0022 100 100 000 Old_age Always - 0
226 Load-in_Time 0x0026 100 100 000 Old_age Always - 259
240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail Offline - 0
SMART Error Log Version: 1
ATA Error Count: 2
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 2 occurred at disk power-on lifetime: 2695 hours (112 days + 7 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 01 d7 5a 71 e0 Error: ICRC, ABRT 1 sectors at LBA = 0x00715ad7 = 7428823
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
35 00 a8 30 57 71 e0 00 01:05:04.969 WRITE DMA EXT
35 00 40 f0 53 71 e0 00 01:05:04.958 WRITE DMA EXT
35 00 20 d0 50 71 e0 00 01:05:04.949 WRITE DMA EXT
35 00 00 d0 4c 71 e0 00 01:05:04.936 WRITE DMA EXT
35 00 00 d0 48 71 e0 00 01:05:04.923 WRITE DMA EXT
Error 1 occurred at disk power-on lifetime: 2552 hours (106 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 01 7f 45 00 e0 Error: ICRC, ABRT 1 sectors at LBA = 0x0000457f = 17791
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
35 00 60 20 44 00 e0 00 00:00:47.023 WRITE DMA EXT
ca 00 08 d0 43 00 e4 00 00:00:47.018 WRITE DMA
ca 00 20 40 42 00 e4 00 00:00:47.017 WRITE DMA
ca 00 78 c0 41 00 e4 00 00:00:47.017 WRITE DMA
ca 00 08 a0 41 00 e4 00 00:00:47.013 WRITE DMA
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 2526 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
دوستان وضعیت هارد از چه خط یا عبارتی قابل تشخیص هست؟
225 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 869به مدت ۱۵ دقیقه 225 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 898225 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 906الان به نظر دوستان بهترین راه حل برای این موضوع چی هستبهترین راه‌حل خرید و استفاده از SSD به جای دیسک سخته
با سلام برای من تو بار اول ک دیدمنترس حالا تا ۶۰۰ هزار تا خیلی مونده من یه هارد دارم بیشتر از ۳میلیون لود سایکل داره ۱۴ ساله دارم ازش کار می کشمکد: [انتخاب]225 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 869به مدت ۱۵ دقیقهکد: [انتخاب]225 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 898
اول تو قسمت تنظیمات برنامه gnome-disk-utility رفتم و مقدار رو apm رو ۲۵۵ گذاشتم
تو مدت ۱۰ دقیقهکد: [انتخاب]225 Load_Cycle_Count 0x0032 100 100 000 Old_age Always - 906
با توجه به اینکه لپتاپم رو ۱ هفته نیست خریدم خیلی داره سریع این مقدارش اظافه میشه
الان به نظر دوستان بهترین راه حل برای این موضوع چی هست
ایا روشی ک شل میساختیم یا روش tlp کدومشون بهترین روش برای اینکه این مشکل نداشه باشیم
ممنون
با توجه به قیمت بالای SSD فکر نمی کنین بهترین راه حل استفاده نکردن از اوبونتو در حین استفاده از باتری باشهالان به نظر دوستان بهترین راه حل برای این موضوع چی هستبهترین راه‌حل خرید و استفاده از SSD به جای دیسک سخته
هر بار من میخوام مهاجرت کنم به گنو/لینوکس یه مشکل بزرگش رو میبینم مردد میشماین باگ نیست. ویندوز هم این کار رو برای کاهش مصرف باتری انجام میده.
چطور باگ به این بزرگی هنوز رفع نشده؟ من میخوام از ابونتو روی لپ تاپ استفاده کنم و اگه این باشه واقعا واسم دردسرساز میشه
من از این کد هایی که می نویسین سر در نمیارم و نمی دونم کجا باید اینارو بنویسم و اصلا بنویسم حل میشه یا نه!؟
یه آموزش و راهنمایی ساده تر و قابل فهم تری نیستش؟با توجه به قیمت بالای SSD فکر نمی کنین بهترین راه حل استفاده نکردن از اوبونتو در حین استفاده از باتری باشهالان به نظر دوستان بهترین راه حل برای این موضوع چی هستبهترین راه‌حل خرید و استفاده از SSD به جای دیسک سخته
خوبه که وقتی داریم از باتری استفاده می کنیم از ویندور بهره ببریم.