انجمنهای فارسی اوبونتو
تازه کار => انجمن تازهکاران => نویسنده: امید در 04 بهمن 1387، 11:36 قظ
-
سلام
بابا من هزار تا از کارهایی را که گفتید کردم اما مودمم نصب نمیشه
تنجمن "نصب و پیکربندی انواع مودم و اتصال به اینترنت." که همش "network eror " میده؟
من scan modem راه هم نصب کردم اما بعدش چی؟
من هیچی از لینوکس نمیدونم و میخوام اینترنتش وصل بشه تا بعد با لینوکس وارد اینترنت بشم و آموزشهاشا بگیرم
لینوکس من اوبنتو 8.10
در قسمت" سیستم>ادمینی استاتور>" گزینه ای به نام network وجود نداره
مودمم دیال آپ زولتریکسه
من یک چیزهایی تو لینوکس دیدم که خیلی بهش علاقه مند شدم اما مشکلات اینچنینی داره اعصابم را خورد میکنه
لطفا تو همین صفحه بگید من برای اینترنت چیکار کنم؟
لطفا ارجاع هم ندید چون هر جا میریم خطای network eror" میده
خیلی ممنون میشم
با تشکر
لطفا یک توضیحی بدید که کارم راه بیفته دیگه
همونطور هم که گفتم چیزی از لینوکس بارم نیست و فقط یک هفتهاست که نصبش کردم
-
خروجی این دستور رو بذارید،، یعنی به مسیر Applications==>Accessories==>Terminal برید و این دستور رو وارد کنید و خروجی اش رو بذارید تو این تاپیک:
lspci
-
بهترین کار اینه که فایل ModemData.txt را که scanModem ایجاد کرده این جا بذارین.
-
با سلام
ببین من هم همین مشکل رو دارم و تو انجمن هم پرسیدم ولی بیجوابه تصمیم گرفتم یه مودم اکسترنال بخرم و خلاص . بنظرم گنو/لینوکس ارزش یه مودم رو داره . وقت و اعصاب هم بیخودی از بین نمیره.
یا علی
-
خروجی این دستور رو بذارید،، یعنی به مسیر Applications==>Accessories==>Terminal برید و این دستور رو وارد کنید و خروجی اش رو بذارید تو این تاپیک:
lspci
ممنون از این که جواب میدید
همچین چیزی را داد:
omid@omid-desktop:~$ lspci
00:00.0 Host bridge: Intel Corporation 82G33/G31/P35/P31 Express DRAM Controller (rev 10)
00:01.0 PCI bridge: Intel Corporation 82G33/G31/P35/P31 Express PCI Express Root Port (rev 10)
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 01)
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 01)
00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (rev 01)
00:1c.2 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 3 (rev 01)
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01)
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01)
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01)
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01)
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1)
00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01)
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01)
00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller (rev 01)
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01)
05:02.0 Communication controller: Conexant Systems, Inc. Conexant SoftK56 Data/Fax Modem (rev 01)
06:00.0 VGA compatible controller: nVidia Corporation GeForce 8500 GT (rev a1)
omid@omid-desktop:~$
-
بهترین کار اینه که فایل ModemData.txt را که scanModem ایجاد کرده این جا بذارین.
من برنامه اسکن مودم را دارم اما نمیدونم چیجوری ازش استفاده کنم
فایلی را که گفتید پیدا نکردم
من فقط روی برنامه scan modem دابل کلیک کردم و با خطای an erir occured while loading archive مواجه شدم
مشکل کجاست؟
چیجورای از یرنامه اسکن مودم استفاده کنم
-
سلام امید جان ببین تو محصولات زوولتریکس دو نوع چیپ بکار رفته ماله تو یا HSF هست یا HCF
خب حالا از این سایت linuxant درایور نوع چیپ خودتو بگیر و نصب کن اینکه نوع چیپ رو چطور بفهمی هم راههایی هست یکی همون استفاده از اسکن مودم هست یه راه جالبی هم هست البته ;D اگه پی سی داری نه لپ تاپ خب خودت میتونی روی خوده مودم نوع چیپش رو ببینی نوشته اینم راه عجیبی بود ;D البته شما با اسکن مودم میشه بدست بیاری
اینم بخش اوبونتو سایت
بخش HSF
http://www.linuxant.com/drivers/hsf/full/downloads-ubuntu-x86.php (http://www.linuxant.com/drivers/hsf/full/downloads-ubuntu-x86.php)
بخش HCF
http://www.linuxant.com/drivers/hcf/full/downloads-ubuntu-x86.php (http://www.linuxant.com/drivers/hcf/full/downloads-ubuntu-x86.php)
اما یک مساله ای هست و انم به خاطر اقدام شرکت کانکسانت نه مودمهای دیگه مثه اینتل و... فقط همین شرکت درایور هاش رو پولی اراپه میده پس درایوری که از اون سایت بگیری راحت نصب میشه و کارم میکنه ولی با سرعت ۱۴ کیلو بایت نه سرعت کامل ولی خب واسه هدف تو که اساسا کشف و نصب و راه اندازی و بکار بردن مودم هست خوب مناسبه و گرنه برای کاربری پیشنهاد میشه در صورت امکان خط adsl یا خط مشابه ای برای اینترنت تهیه کنی و یا بقول دوستی مودم اکسترنال البته قیمت مودم اکسترنال با مودم دی اس ال تقریبا نزدیکه و بیشتر به صرفه هست خط دی اس ال بگیرید اما حتما جهت یاد گیری هم که شده سعی کن با اسکن مودم و درایور مربوطه تو اون سایت که باید نوع متناسب هسته لینوکست و نوع چیپت باشه رو دانلود کنی مودمت رو راه بندازی
موفق باشی
-
سلام امید جان ببین تو محصولات زوولتریکس دو نوع چیپ بکار رفته ماله تو یا HSF هست یا HCF
خب حالا از این سایت linuxant درایور نوع چیپ خودتو بگیر و نصب کن اینکه نوع چیپ رو چطور بفهمی هم راههایی هست یکی همون استفاده از اسکن مودم هست یه راه جالبی هم هست البته ;D اگه پی سی داری نه لپ تاپ خب خودت میتونی روی خوده مودم نوع چیپش رو ببینی نوشته اینم راه عجیبی بود ;D البته شما با اسکن مودم میشه بدست بیاری
از طریق مشاهده شخت افزار مودم چیزی دستگیرم نشد
چیجوری از اسکن مودم استفاده کنم؟
یک سوال دیگه
الان سرعت اینترنت دیال آپ من با ویندوز تقریبا 40 است. یعنی سرعت لینوکس به این سرعت نمیرسه؟
-
دوست عزیز !
اگر هنوز در قسمت scanmodem مشکل داری ؟
از help خود سیستمت استفاده کن !
گوشه سمت راست هلپ قسمت internet
توی اون مدم رو پیدا کن ۴ یه ۵ تا صفحه است تو یکی از اونا به طور کامل گفته scan modem رو چی کار کنی پس از اجرای دستورات یه صفحه باز میشه که اونو اینجا بزار.
موفق باشی.
-
بهترین کار اینه که فایل ModemData.txt را که scanModem ایجاد کرده این جا بذارین.
پیداش کردم
بفرما این هم محتویات فایلی که گفتید:
Only plain text email is forwarded by the Discuss@Linmodems.org List Server,
as HTML can contain viruses. Use as the email Subject Line:
YourName, YourCountry kernel 2.6.27-7-generic
With this Subject Line cogent experts will be alerted, and useful case names left in the Archive.
YourCountry will enable Country specific guidance. Linux experts in YourCountry
can be found through: http://www.linux.org/groups/index.html.
They will know your Country's modem code, which may be essential for dialup service.
Responses from Discuss@Linmodems.org are sometimes blocked by an Internet Provider mail filters.
So in a day, also check the Archived responses at http://www.linmodems.org
-------------------------- System information ----------------------------
CPU=i686,
Linux version 2.6.27-7-generic (buildd@rothera) (gcc version 4.3.2 (Ubuntu 4.3.2-1ubuntu10) ) #1 SMP Fri Oct 24 06:42:44 UTC 2008
scanModem update of: 2009_01_19
There are no blacklisted modem drivers in /etc/modprobe* files
Potentially useful modem drivers now loaded are:
snd_hda_intel
If a USB modem or cellphone is attached and was not detected, please
provide available information in your request to discuss@linmodems.org
For candidate card in slot 05:02.0, firmware information and bootup diagnostics are:
PCI slot PCI ID SubsystemID Name
---------- --------- --------- --------------
05:02.0 14f1:2f50 14f1:205f Communication controller: Conexant Systems, Inc. Conexant SoftK56 Data/Fax Modem
Modem interrupt assignment and sharing:
--- Bootup diagnostics for card in PCI slot 05:02.0 ----
[ 0.521040] PCI: 0000:05:02.0 reg 10 32bit mmio: [f9ff0000, f9ffffff]
[ 0.521047] PCI: 0000:05:02.0 reg 14 io port: [dc00, dc07]
[ 0.521085] pci 0000:05:02.0: PME# supported from D3hot D3cold
[ 0.521089] pci 0000:05:02.0: PME# disabled
The PCI slot 05:02.0 of the modem card may be disabled early in
a bootup process, but then enabled later. If modem drivers load
but the modem is not responsive, read DOCs/Bootup.txt about possible fixes.
Send dmesg.txt along with ModemData.txt to discuss@linmodems.org
if help is needed.
For candidate card in slot 00:1b.0, firmware information and bootup diagnostics are:
PCI slot PCI ID SubsystemID Name
---------- --------- --------- --------------
00:1b.0 8086:27d8 1849:3662 Audio device: Intel Corporation 82801G
Modem interrupt assignment and sharing:
16: 790 826 IO-APIC-fasteoi uhci_hcd:usb4, HDA Intel
--- Bootup diagnostics for card in PCI slot 00:1b.0 ----
[ 0.518208] PCI: 0000:00:1b.0 reg 10 64bit mmio: [f8ffc000, f8ffffff]
[ 0.518208] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.518208] pci 0000:00:1b.0: PME# disabled
[ 9.576689] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[ 9.576709] HDA Intel 0000:00:1b.0: setting latency timer to 64
The PCI slot 00:1b.0 of the modem card may be disabled early in
a bootup process, but then enabled later. If modem drivers load
but the modem is not responsive, read DOCs/Bootup.txt about possible fixes.
Send dmesg.txt along with ModemData.txt to discuss@linmodems.org
if help is needed.
===== Advanced Linux Sound Architecture (ALSA) diagnostics =====
The ALSA packages provide audio support and also drivers for some modems.
ALSA diagnostics are written during bootup to /proc/asound/ folders.
The ALSA verion is 1.0.17
The modem cards detected by "aplay -l" are: None
The /proc/asound/pcm file reports:
-----------------------
00-01: ALC662 Digital : ALC662 Digital : playback 1
00-00: ALC662 Analog : ALC662 Analog : playback 1 : capture 1
about /proc/asound/cards:
------------------------
0 [Intel ]: HDA-Intel - HDA Intel
HDA Intel at 0xf8ffc000 irq 16
PCI slot 00:1b.0 has a High Definition Audio Card
The drivers are in the kernel modules tree at:
/lib/modules/2.6.27-7-generic/kernel/sound/pci/hda/snd-hda-intel.ko
UNEXPECTED HDA diagnostic outcome.
=== Finished firmware and bootup diagnostics, next deducing cogent software. ===
Predictive diagnostics for card in bus 05:02.0:
Modem chipset detected on
NAME="Communication controller: Conexant Systems, Inc. Conexant SoftK56 Data/Fax Modem "
CLASS=0780
PCIDEV=14f1:2f50
SUBSYS=14f1:205f
IRQ=10
IDENT=hsfmodem
Driver=hsfmodem-drivers
For candidate modem in: 05:02.0
0780 Communication controller: Conexant Systems, Inc. Conexant SoftK56 Data/Fax Modem
Primary device ID: 14f1:2f50
Support type needed or chipset: hsfmodem
Writing DOCs/Intel.txt
For owners of a Dell PCs with Conexant HSF modems, a driver source package with full speed enabled is available, but requires driver compiling. Read DOCs/Conexant.txt
Support for the 14f1:2f50 and 14f1:2215 HSF modems is projected early in 2007 from Linuxant.
Start at http://www.linuxant.com/drivers/hsf/downloads-license.php to find the
hsfmodem package matching your System. For several Linux distros, there are
precompiled drivers matched to specific kernels. These have within the FileName,
your KernelVersion: 2.6.27_7_generic
They can be found through http://www.linuxant.com/drivers/hsf/full/downloads.php
A more precise location may be given a few paragraphs below.
If an EXACT Match with your your KernelVersion is not found, one of the
"Generic packages with source" near the bottom of the page must be used.
Downloaded packages must be moved into the Linux partition (home folder is OK)
and unzipped with:
unzip hsf*.zip
The installation command for a .deb suffic packages is, with root/adm permission:
sudo dpkg -i hsf*.deb
while for .rpm suffix it is, with:
rpm -i hsf*.rpm
From http://www.linuxant.com/drivers/hsf/full/downloads-ubuntu-x86.php
download hsfmodem-7.80.02.01full_k2.6.27_7_generic_ubuntu_i386.deb.zip
Under Linux unpack with:
$ unzip hsfmodem*.zip
Then install with:
$ sudo dpkg -i hsfmodem*.deb
Subsequently, the modem should be found with
$ sudo wvdialconf /etc/wvdial.conf
Edit in your personal information with:
$ sudo gedit /etc/wvdial.conf
and try dialing out with:
$ sudo wvdial.
See DOCs/Testing.txt for details.
Read DOCs/Conexant.txt
Writing DOCs/Conexant.txt
Predictive diagnostics for card in bus 00:1b.0:
Modem chipset not detected on
NAME="Audio device: Intel Corporation 82801G "
CLASS=0403
PCIDEV=8086:27d8
SUBSYS=1849:3662
IRQ=16
HDA=8086:27d8
SOFT=8086:27d8.HDA
High Definition Audio (HDA) cards MAY host a modem chip in their Subsystem,
and many are supported by the ALSA audio+modem driver snd-hda-intel
A modem was not detected on HDA card 8086:27d8.
If another modem card is present, then most likely 8086:27d8 does not host a modem.
If another modem card has not been detected, then possibilities are:
1) A Conexant modem chip is present on 8086:27d8, as Conexant chips
are frequently not detectable by ALSA diagnostics
2) The modem may be of the older non-PCI Controller Chipset (hardware) type.
Try detection with Root permission:
sudo wvdialconf /etc/wvdial.conf
For candidate modem in: 00:1b.0
0403 Audio device: Intel Corporation 82801G
Primary device ID: 8086:27d8
Subsystem PCI_id 1849:3662
Softmodem codec or chipset from diagnostics:
from Archives:
Support type needed or chipset:
Support can likely be achieved through two mutually exclusive alternatives:
1) The hsfmodem software for Conexant chipset modems: Read DOCs/Conexant.txt
The following ALSA alternative CANNOT work with Conexant modems.
2) An ALSA modem driver plus slmodemd. Read DOCs/Smartlink.txt for details, and
to test get the package SLMODEMD.gcc4.3.tar.gz from:
http://linmodems.technion.ac.il/packages/smartlink/
----------------end Softmodem section --------------
Writing DOCs/Smartlink.txt
============ end Smartlink section =====================
Completed candidate modem analyses.
The base of the UDEV device file system is: /dev/.udev
Versions adequately match for the compiler installed: 4.3.2
and the compiler used in kernel assembly: 4.3.2
The patch utility is needed and is needed for compiling ALSA drivers, and possibly others.
Minimal compiling resources appear complete:
make utility - /usr/bin/make
Compiler version 4.3
linuc_headers base folder /lib/modules/2.6.27-7-generic/build
However some compilations and executable functions may need additional files,
in the FileNames.h (so called kernel "h"eaders) collection installed in /usr/include/ .
For martian_modem, additional required packages are needed. The also required headers of package libc6 are commonly installed by default.
Compiling hsfmodem drivers does require linux-libc-dev and libc6-dev packages, for kernels 2.6.24 and later versions.
In not included on your install CD, search for them at http://packages.ubuntu.com
or comparable Repository for other Linux distros.
When compiling ALSA drivers, the utility "patch" will also be needed.
If a driver compilation fails, with message including some lack of some FileName.h (stdio.h for example), then
Some additional kernel-header files need installation to /usr/include. The minimal additional packages are libc6-dev
and any of its dependents, under Ubuntu linux-libc-dev
If an alternate ethernet connection is available,
$ apt-get update
$ apt-get -s install linux-kernel-devel
will install needed packages.
For Debian/Ubuntu related distributions, run the following command to display the needed package list:
Otherwise packages have to be found through http://packages.ubuntu.com
Once downloaded and transferred into a Linux partition,
they can be installed alltogether with:
$ sudo dpkg -i *.deb
Checking settings of: /etc/ppp/options
asyncmap 0
noauth
crtscts
lock
hide-password
modem
proxyarp
lcp-echo-interval 30
lcp-echo-failure 4
noipx
In case of a message like:
Warning: Could not modify /etc/ppp/pap-secrets: Permission denied
see http://linmodems.technion.ac.il/bigarch/archive-sixth/msg04656.html
Don't worry about the following, it is for experts should trouble shooting be necessary.
==========================================================
Checking for modem support lines:
--------------------------------------
/device/modem symbolic link:
slmodemd created symbolic link /dev/ttySL0:
Within /etc/udev/ files:
Within /etc/modprobe.conf files:
/etc/modprobe.d/blacklist-modem:# Uncomment these entries in order to blacklist unwanted modem drivers
/etc/modprobe.d/blacklist-modem:# blacklist snd-atiixp-modem
/etc/modprobe.d/blacklist-modem:# blacklist snd-via82xx-modem
/etc/modprobe.d/alsa-base:options snd-atiixp-modem index=-2
/etc/modprobe.d/alsa-base:options snd-via82xx-modem index=-2
Within any ancient /etc/devfs files:
Within ancient kernel 2.4.n /etc/module.conf files:
--------- end modem support lines --------
حالا چیکار کنم؟
-
مودم شما HSF است. لطفا توزیع تون رو بگید و این خروجی رو هم بذارید:
uname -r
تا لینک نسخه مناسب شما رو براتون بذارم.
-
مودم شما HSF است. لطفا توزیع تون رو بگید و این خروجی رو هم بذارید:
uname -r
تا لینک نسخه مناسب شما رو براتون بذارم.
خروجی که گفتید اینه:
2.6.27-7-generic
اما در مورد توزیع حقیقتا من به جز اینکه اوبنتو 8.10 دارم چیزی نمیدونم
اگه منظورتون چیز دیگه ایه بگید از کجا و چیجوری میتونم بفهمم توزیعش چیه
با تشکر از اینکه پیگیر حل مشکل منید
-
لینک دانلود:
http://www.linuxant.com/drivers/hsf/full/archive/hsfmodem-7.80.02.01full/hsfmodem_7.80.02.01full_k2.6.27_7_generic_ubuntu_i386.deb.zip
-
ببخشید این یکی اضافه قرار گرفته که نتونستم حذفش کنم!
-
لینک دانلود:http://www.linuxant.com/drivers/hsf/full/archive/hsfmodem-7.80.02.01full/hsfmodem_7.80.02.01full_k2.6.27_7_generic_ubuntu_i386.deb.zip
مودمم را با کمک شما نصب کردم اما حالا چیجوری وصل اینترنت بشم
توضیح اینکه در بخش administration قسمت system من گزینه ای به نام network وجود نداره
از کجا باید اطلاعات کارت اینترنتم را وارد کنم؟
-
از ویکی غافل نشید:
http://wiki.ubuntu.ir/DialupModemHowto/SetUpDialer#head-4ca4398f98b2b4833fa0d157e64c360ff492f165 (http://wiki.ubuntu.ir/DialupModemHowto/SetUpDialer#head-4ca4398f98b2b4833fa0d157e64c360ff492f165)
این روش رو من امتحان کرده ام و جواب داده. با pppconfig.
;)
-
از ویکی غافل نشید:
http://wiki.ubuntu.ir/DialupModemHowto/SetUpDialer#head-4ca4398f98b2b4833fa0d157e64c360ff492f165 (http://wiki.ubuntu.ir/DialupModemHowto/SetUpDialer#head-4ca4398f98b2b4833fa0d157e64c360ff492f165)
این روش رو من امتحان کرده ام و جواب داده. با pppconfig.
;)
کارهایی که گفتید را انجام دادم و کانکشن فکر کنم درست شده اما بعد از نوشتن کد:
pon provider_alborz
با پیغام زیر مواجه شدم:
Error: only members of the 'dip' group can use this command.
نکته این که من تنها کاربر کامپیوترم
-
از این دستور استفاده کنید:
sudo pon provider_alborz
ضمنا من هرکاری که کردم و خودم رو عضو dip هم کردم، باز هم بدون sudo نشد!
-
از این دستور استفاده کنید:
sudo pon provider_alborz
ضمنا من هرکاری که کردم و خودم رو عضو dip هم کردم، باز هم بدون sudo نشد!
گویا قسمت نیست مشکل ما حل بشه
این بار این پیام را داد:
The file /etc/ppp/peers/provider_alborz does not exist. Please create it or use
a command line argument to use another file in the /etc/ppp/peers/ directory.
-
مطمئنید که اسم کانکشن را درست وارد کردید؟ این ارور می گه همچین کانکشنی نداریم. مثلا اگه کانکشنی که ایجاد کردید اسمش alborz بوده باید بنویسید alborz نه provider_alborz.
-
مطمئنید که اسم کانکشن را درست وارد کردید؟ این ارور می گه همچین کانکشنی نداریم. مثلا اگه کانکشنی که ایجاد کردید اسمش alborz بوده باید بنویسید alborz نه provider_alborz.
نمیدونم چرا اینجوری میشه
شاید از بی سوادی لینوکسی منه
ولی باز هم نشد
نمیدونم چکار کنم
من درمانده شدم
از همتون به خاطر اینکه پیگیر حل مشکل من بودید ممنونم اما گویا باید قید اینترنت لینوکس را زد
-
بنویسین pon و دو باز پشت سر هم کلید Tab رو بزنید. ببینین چی میاره.
یا اینکه بزنید ls /etc/ppp/peers
خروجیشو بزارین اینجا .
-
سلام امید جان برات پیغام خصوصی فرستادم بخونش !
-
ببینید فکر کنم برای هر کار در لینوکس دو راه وجود داره
یکی با کد دادن از طریق ترمینال که من از این طریق به جایی نرسیدم
یکی هم از راه گرافیکی
تو قسمت هلپ لینوکسم اومده برای اتصال به اینترنت از قسمت SYSTEM وارد ADMINISTRATION بشیم و بعد NETWORK را باز کنیم و بعد یک صفحه مثل مال ویندوز میاد و یوزرنیم پسورد و شماره را میدی و کاننکت میشی
مشکل اینه که گزینه ی NETWORK در سیستم من وجود نداره
کسی میدونه چیجوری میشه این گزینه را آورد.شاید اگه اون پیدا بشه بتونم یک کاری بکنم
مسلم جان ازت ممنونم اما باز هم نتیجه نگرفتم(کدها را قبول نمیکرد)
-
ببینید دوست عزیز.
شما connection ای به این اسمی که وارد کرده اید نساخته اید! در دستور sudo pppconfig که بعد از وارد کردن پسورد صفحه اش ظاهر می شه، روی اولین گزینه یعنی create کلیک کنید. حالا در قسمت بعدی باید اسم connection رو وارد کنید. باید با این اسم بعدا وصل بشید. پس اسم رو به دقت وارد کرده و حفظ اش کنید! چون مثلا اگه alborz رو وارد کنید، باید با دستور sudo pon alborz وصل و با sudo poff alborz قطع بشید. به این مسئله دقت کنید و دوباره مراحل رو طی کنید.
:)
-
راست میگن خب درست دستورات رو دنبال کن امید که نا امید نمیشه ;) راستی تازه غیر از اینکه با همون روش ترمینالی میشه کانکشن بسازی که بنظرم بهترین روش هست راه گرافیکی هم داره البته که الان اینترنت نداری تستش کنی ولی بدون واسه نصب رابطش میشه اولین بار که وصل شدی بعده اپدیت لیست مخازن
برای گنوم بزنی
sudo apt-get install gnome-ppp
و برای KDE بزنی
sudo apt-get install kppp
تا شاید در اینده کمی راهتتر شدی ;D
-
سلام دوستان
با وجود همه زحمات و راهنمایی های شما دوستان متاسفانه من به نتیجه مورد نظر نرسیدم.
با این وجود از همه شما به خاطر پیگیری حل مشکلم بسیار سپاسگزارم
روز جمعه عازم دانشگاهم و از رایانه دور خواهم شد و برای همین فعلا پیگیری موضوع منتفی است.
ارادتمندتان امید