TV Card Snazi ...لطفا کمکم کنید نصبش کنم{حل شد}

[yunas]

به نظر می‌آد فقط کافیه مدولشو لود کنید تا قابل استفاده بشه:

کد: [انتخاب]

sudo modprobe saa7134بعد هم با یه برنامه مثل TVTime امتحان کنید که تصویر دارید یا خیر

راه حل شما هم جواب نداد

[hadiaec20h]

منم با کارتم مشکل دارم.
یه سری  از این کارا رو هم که اینجا گفته بودین انجام دادم اما نتیجه ای نگرفتم. وفقط تونستم صفحه no signal رو بیارم . که بعد از ریستارت هم tvtime سعی میکرد به وبکم وصل شه .(از روشن خاموش شدن چراغ وبکم فهمیدم)
بله هر حال سعی من هیچ نتیجه ای نداده و من اصلا نمیتونم تلویزیون بگیرم.
این خروجی lsbci

کد: [انتخاب]

00:00.0 Host bridge: Intel Corporation 82915G/P/GV/GL/PL/910GL Memory Controller Hub (rev 0e)
00:01.0 PCI bridge: Intel Corporation 82915G/P/GV/GL/PL/910GL PCI Express Root Port (rev 0e)
00:1b.0 Audio device: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) High Definition Audio Controller (rev 03)
00:1c.0 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 (rev 03)
00:1c.1 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 2 (rev 03)
00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 03)
00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 03)
00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 03)
00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 03)
00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 03)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev d3)
00:1f.0 ISA bridge: Intel Corporation 82801FB/FR (ICH6/ICH6R) LPC Interface Bridge (rev 03)
00:1f.1 IDE interface: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) IDE Controller (rev 03)
00:1f.2 IDE interface: Intel Corporation 82801FR/FRW (ICH6R/ICH6RW) SATA Controller (rev 03)
00:1f.3 SMBus: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus Controller (rev 03)
01:09.0 Multimedia controller: Philips Semiconductors SAA7130 Video Broadcast Decoder (rev 01)
01:0a.0 Communication controller: Conexant Systems, Inc. HSF 56k HSFi Modem (rev 01)
02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8053 PCI-E Gigabit Ethernet Controller (rev 19)
04:00.0 VGA compatible controller: nVidia Corporation G71 [GeForce 7300 GS] (rev a1)

dmesg:

کد: [انتخاب]

[    0.505146] pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
[    0.505151] pci 0000:00:1d.7: PME# disabled
[    0.505273] pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
[    0.505280] pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
[    0.505284] pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO
[    0.505306] pci 0000:00:1f.1: reg 10 io port: [0x00-0x07]
[    0.505313] pci 0000:00:1f.1: reg 14 io port: [0x00-0x03]
[    0.505320] pci 0000:00:1f.1: reg 18 io port: [0x00-0x07]
[    0.505327] pci 0000:00:1f.1: reg 1c io port: [0x00-0x03]
[    0.505334] pci 0000:00:1f.1: reg 20 io port: [0xffa0-0xffaf]
[    0.505377] pci 0000:00:1f.2: reg 10 io port: [0xa800-0xa807]
[    0.505383] pci 0000:00:1f.2: reg 14 io port: [0xa400-0xa403]
[    0.505389] pci 0000:00:1f.2: reg 18 io port: [0xa000-0xa007]
[    0.505396] pci 0000:00:1f.2: reg 1c io port: [0x9800-0x9803]
[    0.505402] pci 0000:00:1f.2: reg 20 io port: [0x9400-0x940f]
[    0.505409] pci 0000:00:1f.2: reg 24 32bit mmio: [0xcdcffc00-0xcdcfffff]
[    0.505424] pci 0000:00:1f.2: PME# supported from D3hot
[    0.505428] pci 0000:00:1f.2: PME# disabled
[    0.505477] pci 0000:00:1f.3: reg 20 io port: [0x400-0x41f]
[    0.505532] pci 0000:04:00.0: reg 10 32bit mmio: [0xcf000000-0xcfffffff]
[    0.505543] pci 0000:04:00.0: reg 14 64bit mmio: [0xd0000000-0xdfffffff]
[    0.505553] pci 0000:04:00.0: reg 1c 64bit mmio: [0xce000000-0xceffffff]
[    0.505564] pci 0000:04:00.0: reg 30 32bit mmio: [0xcdfe0000-0xcdffffff]
[    0.505616] pci 0000:00:01.0: bridge io port: [0xe000-0xefff]
[    0.505620] pci 0000:00:01.0: bridge 32bit mmio: [0xcdf00000-0xcfffffff]
[    0.505624] pci 0000:00:01.0: bridge 32bit mmio pref: [0xd0000000-0xdfffffff]
[    0.505668] pci 0000:00:1c.0: bridge io port: [0xd000-0xdfff]
[    0.505742] pci 0000:02:00.0: reg 10 64bit mmio: [0xcdefc000-0xcdefffff]
[    0.505751] pci 0000:02:00.0: reg 18 io port: [0xc800-0xc8ff]
[    0.505781] pci 0000:02:00.0: reg 30 32bit mmio: [0xcdec0000-0xcdedffff]
[    0.505794] pci 0000:02:00.0: supports D1 D2
[    0.505796] pci 0000:02:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.505801] pci 0000:02:00.0: PME# disabled
[    0.505848] pci 0000:00:1c.1: bridge io port: [0xc000-0xcfff]
[    0.505852] pci 0000:00:1c.1: bridge 32bit mmio: [0xcde00000-0xcdefffff]
[    0.505907] pci 0000:01:09.0: reg 10 32bit mmio: [0xcddefc00-0xcddeffff]
[    0.505951] pci 0000:01:09.0: supports D1 D2
[    0.505987] pci 0000:01:0a.0: reg 10 32bit mmio: [0xcddf0000-0xcddfffff]
[    0.505994] pci 0000:01:0a.0: reg 14 io port: [0xb800-0xb807]
[    0.506031] pci 0000:01:0a.0: PME# supported from D3hot D3cold
[    0.506035] pci 0000:01:0a.0: PME# disabled
[    0.506071] pci 0000:00:1e.0: transparent bridge
[    0.506076] pci 0000:00:1e.0: bridge io port: [0xb000-0xbfff]
[    0.506080] pci 0000:00:1e.0: bridge 32bit mmio: [0xcdd00000-0xcddfffff]
[    0.506104] bus 00 -> node 0
[    0.506115] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.506421] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[    0.506523] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
[    0.506764] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
[    0.506864] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P5._PRT]
[    0.509542] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[    0.509699] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[    0.509851] ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 10 11 12 14 15)
[    0.510004] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 *6 7 10 11 12 14 15)
[    0.510156] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[    0.510311] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[    0.510464] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[    0.510617] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[    0.510777] ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - 8D, should be 88 [20080926]
[    0.510814] ACPI: WMI: Mapper loaded
[    0.511064] SCSI subsystem initialized
[    0.511121] libata version 3.00 loaded.
[    0.511189] usbcore: registered new interface driver usbfs
[    0.511213] usbcore: registered new interface driver hub
[    0.511253] usbcore: registered new device driver usb
[    0.511402] PCI: Using ACPI for IRQ routing
[    0.511534] Bluetooth: Core ver 2.13
[    0.511534] NET: Registered protocol family 31
[    0.511534] Bluetooth: HCI device and connection manager initialized
[    0.511534] Bluetooth: HCI socket layer initialized
[    0.511534] NET: Registered protocol family 8
[    0.511534] NET: Registered protocol family 20
[    0.511534] NetLabel: Initializing
[    0.511534] NetLabel:  domain hash size = 128
[    0.511534] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.511534] NetLabel:  unlabeled traffic allowed by default
[    0.511534] hpet clockevent registered
[    0.511534] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[    0.511534] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.511534] hpet0: 3 comparators, 64-bit 14.318180 MHz counter
[    0.516084] AppArmor: AppArmor Filesystem Enabled
[    0.516102] pnp: PnP ACPI init
[    0.516102] ACPI: bus type pnp registered
[    0.522064] pnp: PnP ACPI: found 18 devices
[    0.522068] ACPI: ACPI bus type pnp unregistered
[    0.522073] PnPBIOS: Disabled by ACPI PNP
[    0.522088] system 00:01: iomem range 0xfed13000-0xfed19fff has been reserved
[    0.522099] system 00:07: ioport range 0x290-0x297 has been reserved
[    0.522106] system 00:08: ioport range 0x4d0-0x4d1 has been reserved
[    0.522109] system 00:08: ioport range 0x800-0x87f has been reserved
[    0.522112] system 00:08: ioport range 0x400-0x41f has been reserved
[    0.522115] system 00:08: ioport range 0x480-0x4bf has been reserved
[    0.522117] system 00:08: iomem range 0xfed1c000-0xfed1ffff has been reserved
[    0.522120] system 00:08: iomem range 0xfed20000-0xfed8ffff has been reserved
[    0.522123] system 00:08: iomem range 0xffb00000-0xffbfffff could not be reserved
[    0.522126] system 00:08: iomem range 0xfff80000-0xffffffff has been reserved
[    0.522133] system 00:0a: iomem range 0xffc00000-0xfff7ffff has been reserved
[    0.522140] system 00:0d: iomem range 0xfec00000-0xfec00fff has been reserved
[    0.522143] system 00:0d: iomem range 0xfee00000-0xfee00fff has been reserved
[    0.522150] system 00:0f: iomem range 0xe0000000-0xefffffff has been reserved
[    0.522156] system 00:10: iomem range 0xe0000000-0xefffffff has been reserved
[    0.522163] system 00:11: iomem range 0x0-0x9ffff could not be reserved
[    0.522166] system 00:11: iomem range 0xe0000-0xfffff could not be reserved
[    0.522169] system 00:11: iomem range 0x100000-0x7fffffff could not be reserved
[    0.556904] pci 0000:00:01.0: PCI bridge, secondary bus 0000:04
[    0.556909] pci 0000:00:01.0:   IO window: 0xe000-0xefff
[    0.556914] pci 0000:00:01.0:   MEM window: 0xcdf00000-0xcfffffff
[    0.556918] pci 0000:00:01.0:   PREFETCH window: 0x000000d0000000-0x000000dfffffff
[    0.556924] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:03
[    0.556927] pci 0000:00:1c.0:   IO window: 0xd000-0xdfff
[    0.556932] pci 0000:00:1c.0:   MEM window: disabled
[    0.556936] pci 0000:00:1c.0:   PREFETCH window: disabled
[    0.556942] pci 0000:00:1c.1: PCI bridge, secondary bus 0000:02
[    0.556946] pci 0000:00:1c.1:   IO window: 0xc000-0xcfff
[    0.556951] pci 0000:00:1c.1:   MEM window: 0xcde00000-0xcdefffff
[    0.556955] pci 0000:00:1c.1:   PREFETCH window: disabled
[    0.556962] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:01
[    0.556965] pci 0000:00:1e.0:   IO window: 0xb000-0xbfff
[    0.556970] pci 0000:00:1e.0:   MEM window: 0xcdd00000-0xcddfffff
[    0.556974] pci 0000:00:1e.0:   PREFETCH window: disabled
[    0.556993] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.556998] pci 0000:00:01.0: setting latency timer to 64
[    0.557006] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.557010] pci 0000:00:1c.0: setting latency timer to 64
[    0.557019] pci 0000:00:1c.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[    0.557024] pci 0000:00:1c.1: setting latency timer to 64
[    0.557031] pci 0000:00:1e.0: setting latency timer to 64
[    0.557036] bus: 00 index 0 io port: [0x00-0xffff]
[    0.557038] bus: 00 index 1 mmio: [0x000000-0xffffffff]
[    0.557040] bus: 04 index 0 io port: [0xe000-0xefff]
[    0.557043] bus: 04 index 1 mmio: [0xcdf00000-0xcfffffff]
[    0.557045] bus: 04 index 2 mmio: [0xd0000000-0xdfffffff]
[    0.557047] bus: 04 index 3 mmio: [0x0-0x0]
[    0.557049] bus: 03 index 0 io port: [0xd000-0xdfff]
[    0.557051] bus: 03 index 1 mmio: [0x0-0x0]
[    0.557052] bus: 03 index 2 mmio: [0x0-0x0]
[    0.557054] bus: 03 index 3 mmio: [0x0-0x0]
[    0.557056] bus: 02 index 0 io port: [0xc000-0xcfff]
[    0.557058] bus: 02 index 1 mmio: [0xcde00000-0xcdefffff]
[    0.557060] bus: 02 index 2 mmio: [0x0-0x0]
[    0.557062] bus: 02 index 3 mmio: [0x0-0x0]
[    0.557064] bus: 01 index 0 io port: [0xb000-0xbfff]
[    0.557066] bus: 01 index 1 mmio: [0xcdd00000-0xcddfffff]
[    0.557068] bus: 01 index 2 mmio: [0x0-0x0]
[    0.557070] bus: 01 index 3 io port: [0x00-0xffff]
[    0.557072] bus: 01 index 4 mmio: [0x000000-0xffffffff]
[    0.557083] NET: Registered protocol family 2
[    0.557234] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.557570] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.558163] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[    0.558481] TCP: Hash tables configured (established 131072 bind 65536)
[    0.558486] TCP reno registered
[    0.558639] NET: Registered protocol family 1
[    0.558788] checking if image is initramfs... it is
[    1.012072] Switched to high resolution mode on CPU 0
[    1.137477] Freeing initrd memory: 7365k freed
[    1.137587] cpufreq: No nForce2 chipset.
[    1.137734] audit: initializing netlink socket (disabled)
[    1.137752] type=2000 audit(1246408951.136:1): initialized
[    1.145469] highmem bounce pool size: 64 pages
[    1.145476] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[    1.146757] VFS: Disk quotas dquot_6.5.1
[    1.146834] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    1.147550] fuse init (API version 7.10)
[    1.147662] msgmni has been set to 1698
[    1.147891] alg: No test for stdrng (krng)
[    1.147912] io scheduler noop registered
[    1.147915] io scheduler anticipatory registered
[    1.147917] io scheduler deadline registered
[    1.147950] io scheduler cfq registered (default)
[    1.148091] pci 0000:04:00.0: Boot video device
[    1.153174] pcieport-driver 0000:00:01.0: setting latency timer to 64
[    1.153217] pcieport-driver 0000:00:01.0: found MSI capability
[    1.153245] pcieport-driver 0000:00:01.0: irq 2303 for MSI/MSI-X
[    1.153258] pci_express 0000:00:01.0:pcie00: allocate port service
[    1.153280] pci_express 0000:00:01.0:pcie03: allocate port service
[    1.153337] pcieport-driver 0000:00:1c.0: setting latency timer to 64
[    1.153374] pcieport-driver 0000:00:1c.0: found MSI capability
[    1.153401] pcieport-driver 0000:00:1c.0: irq 2302 for MSI/MSI-X
[    1.153415] pci_express 0000:00:1c.0:pcie00: allocate port service
[    1.153432] pci_express 0000:00:1c.0:pcie02: allocate port service
[    1.153447] pci_express 0000:00:1c.0:pcie03: allocate port service
[    1.153509] pcieport-driver 0000:00:1c.1: setting latency timer to 64
[    1.153546] pcieport-driver 0000:00:1c.1: found MSI capability
[    1.153572] pcieport-driver 0000:00:1c.1: irq 2301 for MSI/MSI-X
[    1.153585] pci_express 0000:00:1c.1:pcie00: allocate port service
[    1.153602] pci_express 0000:00:1c.1:pcie02: allocate port service
[    1.153617] pci_express 0000:00:1c.1:pcie03: allocate port service
[    1.153695] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    1.153776] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    1.153924] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[    1.153928] ACPI: Power Button (FF) [PWRF]
[    1.153988] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[    1.153991] ACPI: Power Button (CM) [PWRB]
[    1.154446] processor ACPI_CPU:00: registered as cooling_device0
[    1.154452] ACPI: Processor [CPU1] (supports 8 throttling states)
[    1.157462] isapnp: Scanning for PnP cards...
[    1.509101] isapnp: No Plug & Play device found
[    1.510625] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[    1.510732] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.511252] 00:0e: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.512184] brd: module loaded
[    1.512580] loop: module loaded
[    1.512696] Fixed MDIO Bus: probed
[    1.512703] PPP generic driver version 2.4.2
[    1.512775] input: Macintosh mouse button emulation as /devices/virtual/input/input2
[    1.512816] Driver 'sd' needs updating - please use bus_type methods
[    1.512828] Driver 'sr' needs updating - please use bus_type methods
[    1.512877] ahci 0000:00:1f.2: version 3.0
[    1.512900] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    1.513004] ahci 0000:00:1f.2: AHCI 0001.0000 32 slots 4 ports 1.5 Gbps 0xf impl IDE mode
[    1.513008] ahci 0000:00:1f.2: flags: 64bit ncq pm led slum part
[    1.513013] ahci 0000:00:1f.2: setting latency timer to 64
[    1.513612] scsi0 : ahci
[    1.513748] scsi1 : ahci
[    1.513818] scsi2 : ahci
[    1.513883] scsi3 : ahci
[    1.513939] ata1: SATA max UDMA/133 irq_stat 0x00000040, connection status changed irq 19
[    1.513943] ata2: SATA max UDMA/133 irq_stat 0x00400040, connection status changed irq 19
[    1.513946] ata3: SATA max UDMA/133 abar m1024@0xcdcffc00 port 0xcdcffe00 irq 19
[    1.513949] ata4: SATA max UDMA/133 abar m1024@0xcdcffc00 port 0xcdcffe80 irq 19
[    2.236021] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    2.238215] ata1.00: ATA-7: Maxtor 6V080E0, VA111630, max UDMA/133
[    2.238219] ata1.00: 160086528 sectors, multi 16: LBA48 NCQ (depth 31/32)
[    2.241491] ata1.00: configured for UDMA/133
[    2.980019] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    3.016992] ata2.00: ATA-7: MAXTOR STM3320820AS, 3.AAE, max UDMA/133
[    3.016996] ata2.00: 625142448 sectors, multi 16: LBA48 NCQ (depth 31/32)
[    3.075326] ata2.00: configured for UDMA/133
[    3.408017] ata3: SATA link down (SStatus 0 SControl 300)
[    3.744016] ata4: SATA link down (SStatus 0 SControl 300)
[    3.760140] scsi 0:0:0:0: Direct-Access     ATA      Maxtor 6V080E0   VA11 PQ: 0 ANSI: 5
[    3.760283] sd 0:0:0:0: [sda] 160086528 512-byte hardware sectors: (81.9 GB/76.3 GiB)
[    3.760307] sd 0:0:0:0: [sda] Write Protect is off
[    3.760310] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    3.760346] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    3.760446] sd 0:0:0:0: [sda] 160086528 512-byte hardware sectors: (81.9 GB/76.3 GiB)
[    3.760467] sd 0:0:0:0: [sda] Write Protect is off
[    3.760471] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    3.760505] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    3.760511]  sda: sda1 sda2 < sda5 sda6 >
[    3.799952] sd 0:0:0:0: [sda] Attached SCSI disk
[    3.800044] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    3.800169] scsi 1:0:0:0: Direct-Access     ATA      MAXTOR STM332082 3.AA PQ: 0 ANSI: 5
[    3.800296] sd 1:0:0:0: [sdb] 625142448 512-byte hardware sectors: (320 GB/298 GiB)
[    3.800319] sd 1:0:0:0: [sdb] Write Protect is off
[    3.800322] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[    3.800357] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    3.800448] sd 1:0:0:0: [sdb] 625142448 512-byte hardware sectors: (320 GB/298 GiB)
[    3.800470] sd 1:0:0:0: [sdb] Write Protect is off
[    3.800473] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[    3.800507] sd 1:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    3.800512]  sdb: sdb1
[    3.814865] sd 1:0:0:0: [sdb] Attached SCSI disk
[    3.814927] sd 1:0:0:0: Attached scsi generic sg1 type 0
[    3.814990] ata_piix 0000:00:1f.1: version 2.12
[    3.815008] ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[    3.815054] ata_piix 0000:00:1f.1: setting latency timer to 64
[    3.815163] scsi4 : ata_piix
[    3.815251] scsi5 : ata_piix
[    3.817189] ata5: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[    3.817193] ata6: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[    3.980554] ata5.00: ATAPI: DVD RW DRU-820A, 1.0c, max UDMA/66
[    3.980594] ata5.01: ATAPI: ASUS    CRW-5232A4, 1.02, max UDMA/33
[    3.996402] ata5.00: configured for UDMA/66
[    4.012296] ata5.01: configured for UDMA/33
[    4.179572] scsi 4:0:0:0: CD-ROM            SONY     DVD RW DRU-820A  1.0c PQ: 0 ANSI: 5
[    4.185385] sr0: scsi3-mmc drive: 125x/125x writer dvd-ram cd/rw xa/form2 cdda tray
[    4.185390] Uniform CD-ROM driver Revision: 3.20
[    4.185525] sr 4:0:0:0: Attached scsi CD-ROM sr0
[    4.185592] sr 4:0:0:0: Attached scsi generic sg2 type 5
[    4.186176] scsi 4:0:1:0: CD-ROM            ASUS     CRW-5232A4       1.02 PQ: 0 ANSI: 5
[    4.188385] sr1: scsi3-mmc drive: 52x/52x writer cd/rw xa/form2 cdda tray
[    4.188491] sr 4:0:1:0: Attached scsi CD-ROM sr1
[    4.188553] sr 4:0:1:0: Attached scsi generic sg3 type 5
[    4.189236] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    4.189273] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    4.189297] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[    4.189301] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    4.189387] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[    4.193292] ehci_hcd 0000:00:1d.7: debug port 1
[    4.193300] ehci_hcd 0000:00:1d.7: cache line size of 128 is not supported
[    4.193317] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xcdcff800
[    4.208014] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    4.208110] usb usb1: configuration #1 chosen from 1 choice
[    4.208147] hub 1-0:1.0: USB hub found
[    4.208157] hub 1-0:1.0: 8 ports detected
[    4.208305] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    4.208331] uhci_hcd: USB Universal Host Controller Interface driver
[    4.208379] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    4.208388] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    4.208392] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    4.208466] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[    4.208493] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00008000
[    4.208586] usb usb2: configuration #1 chosen from 1 choice
[    4.208616] hub 2-0:1.0: USB hub found
[    4.208626] hub 2-0:1.0: 2 ports detected
[    4.208738] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    4.208745] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    4.208749] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    4.208804] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[    4.208831] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00008400
[    4.208920] usb usb3: configuration #1 chosen from 1 choice
[    4.208951] hub 3-0:1.0: USB hub found
[    4.208967] hub 3-0:1.0: 2 ports detected
[    4.209078] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    4.209086] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    4.209090] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    4.209158] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[    4.209197] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00008800
[    4.209298] usb usb4: configuration #1 chosen from 1 choice
[    4.209329] hub 4-0:1.0: USB hub found
[    4.209338] hub 4-0:1.0: 2 ports detected
[    4.209448] uhci_hcd 0000:00:1d.3: PCI INT D -> GSI 16 (level, low) -> IRQ 16
[    4.209457] uhci_hcd 0000:00:1d.3: setting latency timer to 64
[    4.209460] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[    4.209524] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[    4.209559] uhci_hcd 0000:00:1d.3: irq 16, io base 0x00009000
[    4.209650] usb usb5: configuration #1 chosen from 1 choice
[    4.209681] hub 5-0:1.0: USB hub found
[    4.209691] hub 5-0:1.0: 2 ports detected
[    4.209855] usbcore: registered new interface driver libusual
[    4.209896] usbcore: registered new interface driver usbserial
[    4.209910] USB Serial support registered for generic
[    4.209927] usbcore: registered new interface driver usbserial_generic
[    4.209930] usbserial: USB Serial Driver core
[    4.209994] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f03:PS2M] at 0x60,0x64 irq 1,12
[    4.212701] serio: i8042 KBD port at 0x60,0x64 irq 1
[    4.212708] serio: i8042 AUX port at 0x60,0x64 irq 12
[    4.212870] mice: PS/2 mouse device common for all mice
[    4.213047] rtc_cmos 00:03: RTC can wake from S4
[    4.213098] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[    4.213128] rtc0: alarms up to one month, 114 bytes nvram, hpet irqs
[    4.213223] device-mapper: uevent: version 1.0.3
[    4.213391] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
[    4.213468] device-mapper: multipath: version 1.0.5 loaded
[    4.213472] device-mapper: multipath round-robin: version 1.0.0 loaded
[    4.213591] EISA: Probing bus 0 at eisa.0
[    4.213618] Cannot allocate resource for EISA slot 8
[    4.213620] EISA: Detected 0 cards.
[    4.213659] cpuidle: using governor ladder
[    4.213662] cpuidle: using governor menu
[    4.214244] TCP cubic registered
[    4.214339] NET: Registered protocol family 10
[    4.214787] lo: Disabled Privacy Extensions
[    4.215133] NET: Registered protocol family 17
[    4.215163] Bluetooth: L2CAP ver 2.11
[    4.215165] Bluetooth: L2CAP socket layer initialized
[    4.215168] Bluetooth: SCO (Voice Link) ver 0.6
[    4.215170] Bluetooth: SCO socket layer initialized
[    4.215219] Bluetooth: RFCOMM socket layer initialized
[    4.215229] Bluetooth: RFCOMM TTY layer initialized
[    4.215231] Bluetooth: RFCOMM ver 1.10
[    4.215294] Using IPI No-Shortcut mode
[    4.215406] registered taskstats version 1
[    4.215521]   Magic number: 1:759:707
[    4.215604] rtc_cmos 00:03: setting system clock to 2009-07-01 00:42:34 UTC (1246408954)
[    4.215608] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    4.215610] EDD information not available.
[    4.215995] Freeing unused kernel memory: 532k freed
[    4.216138] Write protecting the kernel text: 4128k
[    4.216176] Write protecting the kernel read-only data: 1532k
[    4.242770] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
[    4.912041] usb 1-4: new high speed USB device using ehci_hcd and address 4
[    5.117575] sky2 driver version 1.22
[    5.117623] sky2 0000:02:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    5.117636] sky2 0000:02:00.0: setting latency timer to 64
[    5.117710] sky2 0000:02:00.0: Yukon-2 EC chip revision 2
[    5.149578] sky2 0000:02:00.0: Marvell Yukon 88E8053 Gigabit Ethernet Controller
[    5.149581]  Part Number: Yukon 88E8053
[    5.149583]  Engineering Level: Rev. 1.9
[    5.149585]  Manufacturer: Marvell
[    5.149647] sky2 0000:02:00.0: irq 2300 for MSI/MSI-X
[    5.154973] sky2 eth0: addr 00:15:f2:da:94:ca
[    5.168522] usb 1-4: configuration #1 chosen from 1 choice
[    5.168719] hub 1-4:1.0: USB hub found
[    5.168803] hub 1-4:1.0: 4 ports detected
[    5.408042] usb 2-2: new full speed USB device using uhci_hcd and address 2
[    5.616746] usb 2-2: configuration #1 chosen from 1 choice
[    5.856045] usb 3-1: new full speed USB device using uhci_hcd and address 2
[    6.047293] usb 3-1: configuration #2 chosen from 2 choices
[    6.068799] PM: Starting manual resume from disk
[    6.068804] PM: Resume from partition 8:5
[    6.068806] PM: Checking hibernation image.
[    6.068961] PM: Resume from disk failed.
[    6.090671] EXT4-fs: barriers enabled
[    6.103062] kjournald2 starting.  Commit interval 5 seconds
[    6.103079] EXT4-fs: delayed allocation enabled
[    6.103081] EXT4-fs: file extents enabled
[    6.104728] EXT4-fs: mballoc enabled
[    6.104735] EXT4-fs: mounted filesystem with ordered data mode.
[    6.148154] usb 1-4.3: new full speed USB device using ehci_hcd and address 5
[    6.258604] usb 1-4.3: configuration #1 chosen from 1 choice
[   10.235424] udev: starting version 141
[   10.390517] Linux agpgart interface v0.103
[   10.468773] parport_pc 00:06: reported by Plug and Play ACPI
[   10.468922] parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
[   10.829364] nvidia: module license 'NVIDIA' taints kernel.
[   11.166193] Linux video capture interface: v2.00
[   11.183380] Bluetooth: Generic Bluetooth USB driver ver 0.3
[   11.183536] usbcore: registered new interface driver btusb
[   11.213383] intel_rng: FWH not detected
[   11.269127] input: PC Speaker as /devices/platform/pcspkr/input/input4
[   11.320273] eth1: register 'cdc_ether' at usb-0000:00:1d.1-1, CDC Ethernet Device, 00:21:27:d7:b4:83
[   11.320322] usbcore: registered new interface driver cdc_ether
[   11.382563] nvidia 0000:04:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[   11.382572] nvidia 0000:04:00.0: setting latency timer to 64
[   11.382925] NVRM: loading NVIDIA UNIX x86 Kernel Module  180.44  Mon Mar 23 14:59:10 PST 2009
[   11.396222] gspca: main v2.3.0 registered
[   11.412922] gspca: probing 0ac8:307b
[   11.570731] iTCO_vendor_support: vendor-support=0
[   11.572682] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
[   11.572934] iTCO_wdt: Found a ICH6 or ICH6R TCO device (Version=2, TCOBASE=0x0860)
[   11.573072] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[   11.604746] synaptics was reset on resume, see synaptics_resume_reset if you have trouble on resume
[   11.673162] ppdev: user-space parallel port driver
[   11.703586] saa7134: `3;tuner=2' invalid for parameter `card'
[   11.744296] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[   11.744302] hda_intel: position_fix set to 1 for device 1043:813d
[   11.744409] HDA Intel 0000:00:1b.0: setting latency timer to 64
[   12.140041] psmouse serio1: ID: 10 00 64<6>zc3xx: probe 2wr ov vga 0x7648
[   12.314139] zc3xx: probe 3wr vga 1 0x4001
[   12.487157] zc3xx: probe sensor -> 7648
[   12.487160] zc3xx: Find Sensor OV7648
[   12.490313] gspca: probe ok
[   12.490356] usbcore: registered new interface driver zc3xx
[   12.490400] zc3xx: registered
[   12.642904] lp0: using parport0 (interrupt-driven).
[   12.698181] bttv: driver version 0.9.17 loaded
[   12.698186] bttv: using 8 buffers with 2080k (520 pages) each for capture
[   12.768671] input: ImPS/2 Generic Wheel Mouse as /devices/platform/i8042/serio1/input/input5
[   12.855101] Adding 4192924k swap on /dev/sda5.  Priority:-1 extents:1 across:4192924k
[   13.419167] EXT4 FS on sda6, internal journal on sda6:8
[   14.617060] type=1505 audit(1246392764.900:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=2092
[   14.672441] type=1505 audit(1246392764.956:3): operation="profile_load" name="/sbin/dhclient-script" name2="default" pid=2096
[   14.672615] type=1505 audit(1246392764.956:4): operation="profile_load" name="/sbin/dhclient3" name2="default" pid=2096
[   14.672699] type=1505 audit(1246392764.956:5): operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" name2="default" pid=2096
[   14.672770] type=1505 audit(1246392764.956:6): operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" name2="default" pid=2096
[   14.824998] type=1505 audit(1246392765.108:7): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=2101
[   14.825231] type=1505 audit(1246392765.108:8): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=2101
[   14.859147] type=1505 audit(1246392765.140:9): operation="profile_load" name="/usr/sbin/tcpdump" name2="default" pid=2105
[   19.062952] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   19.062956] Bluetooth: BNEP filters: protocol multicast
[   19.090483] Bridge firewalling registered
[   24.720474] sky2 eth0: enabling interface
[   24.720623] ADDRCONF(NETDEV_UP): eth0: link is not ready
[   26.033483] hda-intel: IRQ timing workaround is activated for card #0. Suggest a bigger bdl_pos_adj.
[   26.517635] sky2 eth0: Link is up at 100 Mbps, full duplex, flow control both
[   26.517849] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   34.916012] eth1: no IPv6 routers present
[   36.940012] eth0: no IPv6 routers present
[   55.327843] UDF-fs: No VRS found
[   55.388747] ISO 9660 Extensions: Microsoft Joliet Level 3
[   55.389400] ISOFS: changing to secondary root
[  141.254751] NET: Registered protocol family 24


[Ali.M]

سلام
من تازه کارم اگه میشه کمکم کنی کارت تی ویم رو راه بندازم ممنون میشم
این خروجی lspci

کد: [انتخاب]

00:00.0 Host bridge: Intel Corporation 4 Series Chipset DRAM Controller (rev 03)
00:01.0 PCI bridge: Intel Corporation 4 Series Chipset PCI Express Root Port (rev 03)
00:1a.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #4
00:1a.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #5
00:1a.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #6
00:1a.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #2
00:1b.0 Audio device: Intel Corporation 82801JI (ICH10 Family) HD Audio Controller
00:1c.0 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 1
00:1c.4 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 5
00:1c.5 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 6
00:1d.0 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #1
00:1d.1 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #2
00:1d.2 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #3
00:1d.7 USB Controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #1
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 90)
00:1f.0 ISA bridge: Intel Corporation 82801JIB (ICH10) LPC Interface Controller
00:1f.2 IDE interface: Intel Corporation 82801JI (ICH10 Family) 4 port SATA IDE Controller
00:1f.3 SMBus: Intel Corporation 82801JI (ICH10 Family) SMBus Controller
00:1f.5 IDE interface: Intel Corporation 82801JI (ICH10 Family) 2 port SATA IDE Controller
01:00.0 VGA compatible controller: nVidia Corporation GeForce 8500 GT (rev a1)
03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02)
04:00.0 IDE interface: JMicron Technologies, Inc. JMB368 IDE controller
05:01.0 Communication controller: Conexant Systems, Inc. HSF 56k HSFi Modem (rev 01)
05:02.0 Multimedia controller: Philips Semiconductors SAA7130 Video Broadcast Decoder (rev 01)
این هم خروجی dmesg

کد: [انتخاب]

[    0.416219] pci 0000:00:1f.2: reg 18 io port: [0x00-0x07]
[    0.416223] pci 0000:00:1f.2: reg 1c io port: [0x00-0x03]
[    0.416228] pci 0000:00:1f.2: reg 20 io port: [0xff90-0xff9f]
[    0.416234] pci 0000:00:1f.2: reg 24 io port: [0xffa0-0xffaf]
[    0.416265] pci 0000:00:1f.3: reg 10 64bit mmio: [0xf9fff400-0xf9fff4ff]
[    0.416277] pci 0000:00:1f.3: reg 20 io port: [0x400-0x41f]
[    0.416314] pci 0000:00:1f.5: reg 10 io port: [0x9c00-0x9c07]
[    0.416319] pci 0000:00:1f.5: reg 14 io port: [0x9880-0x9883]
[    0.416325] pci 0000:00:1f.5: reg 18 io port: [0x9800-0x9807]
[    0.416329] pci 0000:00:1f.5: reg 1c io port: [0x9480-0x9483]
[    0.416334] pci 0000:00:1f.5: reg 20 io port: [0x9400-0x940f]
[    0.416339] pci 0000:00:1f.5: reg 24 io port: [0x9080-0x908f]
[    0.416381] pci 0000:01:00.0: reg 10 32bit mmio: [0xfd000000-0xfdffffff]
[    0.416390] pci 0000:01:00.0: reg 14 64bit mmio: [0xc0000000-0xdfffffff]
[    0.416398] pci 0000:01:00.0: reg 1c 64bit mmio: [0xfa000000-0xfbffffff]
[    0.416403] pci 0000:01:00.0: reg 24 io port: [0xbc00-0xbc7f]
[    0.416408] pci 0000:01:00.0: reg 30 32bit mmio: [0xfe9e0000-0xfe9fffff]
[    0.416450] pci 0000:00:01.0: bridge io port: [0xb000-0xbfff]
[    0.416453] pci 0000:00:01.0: bridge 32bit mmio: [0xfa000000-0xfe9fffff]
[    0.416457] pci 0000:00:01.0: bridge 64bit mmio pref: [0xc0000000-0xdfffffff]
[    0.416539] pci 0000:03:00.0: reg 10 io port: [0xc800-0xc8ff]
[    0.416558] pci 0000:03:00.0: reg 18 64bit mmio: [0xfeaff000-0xfeafffff]
[    0.416572] pci 0000:03:00.0: reg 20 64bit mmio: [0xf8ff0000-0xf8ffffff]
[    0.416579] pci 0000:03:00.0: reg 30 32bit mmio: [0xfeac0000-0xfeadffff]
[    0.416589] pci 0000:03:00.0: supports D1 D2
[    0.416591] pci 0000:03:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    0.416595] pci 0000:03:00.0: PME# disabled
[    0.416644] pci 0000:00:1c.4: bridge io port: [0xc000-0xcfff]
[    0.416648] pci 0000:00:1c.4: bridge 32bit mmio: [0xfea00000-0xfeafffff]
[    0.416653] pci 0000:00:1c.4: bridge 64bit mmio pref: [0xf8f00000-0xf8ffffff]
[    0.416706] pci 0000:04:00.0: reg 10 io port: [0xdc00-0xdc07]
[    0.416714] pci 0000:04:00.0: reg 14 io port: [0xd880-0xd883]
[    0.416723] pci 0000:04:00.0: reg 18 io port: [0xd800-0xd807]
[    0.416731] pci 0000:04:00.0: reg 1c io port: [0xd480-0xd483]
[    0.416739] pci 0000:04:00.0: reg 20 io port: [0xd400-0xd40f]
[    0.416806] pci 0000:00:1c.5: bridge io port: [0xd000-0xdfff]
[    0.416842] pci 0000:05:01.0: reg 10 32bit mmio: [0xfebf0000-0xfebfffff]
[    0.416848] pci 0000:05:01.0: reg 14 io port: [0xec00-0xec07]
[    0.416878] pci 0000:05:01.0: PME# supported from D3hot D3cold
[    0.416881] pci 0000:05:01.0: PME# disabled
[    0.416912] pci 0000:05:02.0: reg 10 32bit mmio: [0xfebefc00-0xfebeffff]
[    0.416947] pci 0000:05:02.0: supports D1 D2
[    0.416987] pci 0000:00:1e.0: transparent bridge
[    0.416990] pci 0000:00:1e.0: bridge io port: [0xe000-0xefff]
[    0.416993] pci 0000:00:1e.0: bridge 32bit mmio: [0xfeb00000-0xfebfffff]
[    0.417015] bus 00 -> node 0
[    0.417020] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.417226] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[    0.417394] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
[    0.417481] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT]
[    0.417564] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT]
[    0.420100] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[    0.420207] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[    0.420312] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[    0.420417] ACPI: PCI Interrupt Link [LNKD] (IRQs *3 4 5 6 7 10 11 12 14 15)
[    0.420523] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[    0.420628] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[    0.420732] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[    0.420837] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[    0.420942] ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - F6, should be E9 [20080926]
[    0.420961] ACPI: WMI: Mapper loaded
[    0.420989] SCSI subsystem initialized
[    0.420989] libata version 3.00 loaded.
[    0.420989] usbcore: registered new interface driver usbfs
[    0.420989] usbcore: registered new interface driver hub
[    0.420989] usbcore: registered new device driver usb
[    0.420989] PCI: Using ACPI for IRQ routing
[    0.428013] Bluetooth: Core ver 2.13
[    0.428036] NET: Registered protocol family 31
[    0.428036] Bluetooth: HCI device and connection manager initialized
[    0.428036] Bluetooth: HCI socket layer initialized
[    0.428036] NET: Registered protocol family 8
[    0.428036] NET: Registered protocol family 20
[    0.428036] NetLabel: Initializing
[    0.428036] NetLabel:  domain hash size = 128
[    0.428036] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.428046] NetLabel:  unlabeled traffic allowed by default
[    0.428095] AppArmor: AppArmor Filesystem Enabled
[    0.432015] pnp: PnP ACPI init
[    0.432027] ACPI: bus type pnp registered
[    0.435485] pnp: PnP ACPI: found 14 devices
[    0.435487] ACPI: ACPI bus type pnp unregistered
[    0.435490] PnPBIOS: Disabled by ACPI PNP
[    0.435497] system 00:01: iomem range 0xfed14000-0xfed19fff has been reserved
[    0.435499] system 00:01: iomem range 0xfed90000-0xfed93fff has been reserved
[    0.435506] system 00:09: ioport range 0xa00-0xadf has been reserved
[    0.435508] system 00:09: ioport range 0xae0-0xaef has been reserved
[    0.435512] system 00:0a: ioport range 0x4d0-0x4ff has been reserved
[    0.435514] system 00:0a: ioport range 0x800-0x87f has been reserved
[    0.435516] system 00:0a: ioport range 0x480-0x4cf has been reserved
[    0.435518] system 00:0a: iomem range 0xfed1c000-0xfed1ffff has been reserved
[    0.435520] system 00:0a: iomem range 0xfed20000-0xfed3ffff has been reserved
[    0.435522] system 00:0a: iomem range 0xfed40000-0xfed8ffff has been reserved
[    0.435526] system 00:0b: iomem range 0xfec00000-0xfec00fff has been reserved
[    0.435528] system 00:0b: iomem range 0xfee00000-0xfee00fff has been reserved
[    0.435532] system 00:0c: iomem range 0xe0000000-0xefffffff has been reserved
[    0.435537] system 00:0d: iomem range 0x0-0x9ffff could not be reserved
[    0.435539] system 00:0d: iomem range 0xc0000-0xcffff could not be reserved
[    0.435541] system 00:0d: iomem range 0xe0000-0xfffff could not be reserved
[    0.435543] system 00:0d: iomem range 0x100000-0x7fffffff could not be reserved
[    0.435545] system 00:0d: iomem range 0xfed90000-0xffffffff could not be reserved
[    0.470197] pci 0000:00:01.0: PCI bridge, secondary bus 0000:01
[    0.470199] pci 0000:00:01.0:   IO window: 0xb000-0xbfff
[    0.470202] pci 0000:00:01.0:   MEM window: 0xfa000000-0xfe9fffff
[    0.470205] pci 0000:00:01.0:   PREFETCH window: 0x000000c0000000-0x000000dfffffff
[    0.470209] pci 0000:00:1c.0: PCI bridge, secondary bus 0000:02
[    0.470210] pci 0000:00:1c.0:   IO window: disabled
[    0.470214] pci 0000:00:1c.0:   MEM window: disabled
[    0.470217] pci 0000:00:1c.0:   PREFETCH window: disabled
[    0.470222] pci 0000:00:1c.4: PCI bridge, secondary bus 0000:03
[    0.470225] pci 0000:00:1c.4:   IO window: 0xc000-0xcfff
[    0.470229] pci 0000:00:1c.4:   MEM window: 0xfea00000-0xfeafffff
[    0.470232] pci 0000:00:1c.4:   PREFETCH window: 0x000000f8f00000-0x000000f8ffffff
[    0.470237] pci 0000:00:1c.5: PCI bridge, secondary bus 0000:04
[    0.470240] pci 0000:00:1c.5:   IO window: 0xd000-0xdfff
[    0.470243] pci 0000:00:1c.5:   MEM window: disabled
[    0.470246] pci 0000:00:1c.5:   PREFETCH window: disabled
[    0.470252] pci 0000:00:1e.0: PCI bridge, secondary bus 0000:05
[    0.470254] pci 0000:00:1e.0:   IO window: 0xe000-0xefff
[    0.470258] pci 0000:00:1e.0:   MEM window: 0xfeb00000-0xfebfffff
[    0.470261] pci 0000:00:1e.0:   PREFETCH window: disabled
[    0.470271] pci 0000:00:01.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.470274] pci 0000:00:01.0: setting latency timer to 64
[    0.470280] pci 0000:00:1c.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.470283] pci 0000:00:1c.0: setting latency timer to 64
[    0.470289] pci 0000:00:1c.4: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    0.470292] pci 0000:00:1c.4: setting latency timer to 64
[    0.470299] pci 0000:00:1c.5: PCI INT B -> GSI 17 (level, low) -> IRQ 17
[    0.470302] pci 0000:00:1c.5: setting latency timer to 64
[    0.470307] pci 0000:00:1e.0: setting latency timer to 64
[    0.470310] bus: 00 index 0 io port: [0x00-0xffff]
[    0.470312] bus: 00 index 1 mmio: [0x000000-0xffffffff]
[    0.470313] bus: 01 index 0 io port: [0xb000-0xbfff]
[    0.470315] bus: 01 index 1 mmio: [0xfa000000-0xfe9fffff]
[    0.470317] bus: 01 index 2 mmio: [0xc0000000-0xdfffffff]
[    0.470318] bus: 01 index 3 mmio: [0x0-0x0]
[    0.470319] bus: 02 index 0 mmio: [0x0-0x0]
[    0.470321] bus: 02 index 1 mmio: [0x0-0x0]
[    0.470322] bus: 02 index 2 mmio: [0x0-0x0]
[    0.470323] bus: 02 index 3 mmio: [0x0-0x0]
[    0.470325] bus: 03 index 0 io port: [0xc000-0xcfff]
[    0.470326] bus: 03 index 1 mmio: [0xfea00000-0xfeafffff]
[    0.470328] bus: 03 index 2 mmio: [0xf8f00000-0xf8ffffff]
[    0.470329] bus: 03 index 3 mmio: [0x0-0x0]
[    0.470331] bus: 04 index 0 io port: [0xd000-0xdfff]
[    0.470332] bus: 04 index 1 mmio: [0x0-0x0]
[    0.470333] bus: 04 index 2 mmio: [0x0-0x0]
[    0.470334] bus: 04 index 3 mmio: [0x0-0x0]
[    0.470336] bus: 05 index 0 io port: [0xe000-0xefff]
[    0.470337] bus: 05 index 1 mmio: [0xfeb00000-0xfebfffff]
[    0.470339] bus: 05 index 2 mmio: [0x0-0x0]
[    0.470340] bus: 05 index 3 io port: [0x00-0xffff]
[    0.470342] bus: 05 index 4 mmio: [0x000000-0xffffffff]
[    0.470348] NET: Registered protocol family 2
[    0.484085] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.484266] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.484547] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[    0.484705] TCP: Hash tables configured (established 131072 bind 65536)
[    0.484706] TCP reno registered
[    0.492100] NET: Registered protocol family 1
[    0.492194] checking if image is initramfs... it is
[    0.968549] Switched to high resolution mode on CPU 1
[    0.972067] Switched to high resolution mode on CPU 0
[    0.974189] Freeing initrd memory: 7365k freed
[    0.974358] cpufreq: No nForce2 chipset.
[    0.974467] audit: initializing netlink socket (disabled)
[    0.974485] type=2000 audit(1250254638.972:1): initialized
[    0.980235] highmem bounce pool size: 64 pages
[    0.980239] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[    0.981227] VFS: Disk quotas dquot_6.5.1
[    0.981271] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[    0.981728] fuse init (API version 7.10)
[    0.981791] msgmni has been set to 1698
[    0.981927] alg: No test for stdrng (krng)
[    0.981935] io scheduler noop registered
[    0.981936] io scheduler anticipatory registered
[    0.981938] io scheduler deadline registered
[    0.981948] io scheduler cfq registered (default)
[    0.982078] pci 0000:01:00.0: Boot video device
[    0.984905] pcieport-driver 0000:00:01.0: setting latency timer to 64
[    0.984933] pcieport-driver 0000:00:01.0: found MSI capability
[    0.984952] pcieport-driver 0000:00:01.0: irq 2303 for MSI/MSI-X
[    0.984959] pci_express 0000:00:01.0:pcie00: allocate port service
[    0.984969] pci_express 0000:00:01.0:pcie03: allocate port service
[    0.985006] pcieport-driver 0000:00:1c.0: setting latency timer to 64
[    0.985035] pcieport-driver 0000:00:1c.0: found MSI capability
[    0.985055] pcieport-driver 0000:00:1c.0: irq 2302 for MSI/MSI-X
[    0.985065] pci_express 0000:00:1c.0:pcie00: allocate port service
[    0.985074] pci_express 0000:00:1c.0:pcie02: allocate port service
[    0.985083] pci_express 0000:00:1c.0:pcie03: allocate port service
[    0.985128] pcieport-driver 0000:00:1c.4: setting latency timer to 64
[    0.985157] pcieport-driver 0000:00:1c.4: found MSI capability
[    0.985177] pcieport-driver 0000:00:1c.4: irq 2301 for MSI/MSI-X
[    0.985187] pci_express 0000:00:1c.4:pcie00: allocate port service
[    0.985196] pci_express 0000:00:1c.4:pcie02: allocate port service
[    0.985207] pci_express 0000:00:1c.4:pcie03: allocate port service
[    0.985252] pcieport-driver 0000:00:1c.5: setting latency timer to 64
[    0.985281] pcieport-driver 0000:00:1c.5: found MSI capability
[    0.985301] pcieport-driver 0000:00:1c.5: irq 2300 for MSI/MSI-X
[    0.985311] pci_express 0000:00:1c.5:pcie00: allocate port service
[    0.985320] pci_express 0000:00:1c.5:pcie02: allocate port service
[    0.985329] pci_express 0000:00:1c.5:pcie03: allocate port service
[    0.985383] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[    0.985814] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
[    0.985926] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[    0.985928] ACPI: Power Button (FF) [PWRF]
[    0.985969] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[    0.985971] ACPI: Power Button (CM) [PWRB]
[    0.986178] processor ACPI_CPU:00: registered as cooling_device0
[    0.986204] processor ACPI_CPU:01: registered as cooling_device1
[    0.988035] thermal LNXTHERM:01: registered as thermal_zone0
[    0.988239] ACPI: Thermal Zone [THRM] (48 C)
[    0.988276] isapnp: Scanning for PnP cards...
[    1.343874] isapnp: No Plug & Play device found
[    1.352630] Serial: 8250/16550 driver4 ports, IRQ sharing enabled
[    1.352713] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.352992] 00:06: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[    1.353602] brd: module loaded
[    1.353833] loop: module loaded
[    1.353878] Fixed MDIO Bus: probed
[    1.353882] PPP generic driver version 2.4.2
[    1.353923] input: Macintosh mouse button emulation as /devices/virtual/input/input2
[    1.353943] Driver 'sd' needs updating - please use bus_type methods
[    1.353950] Driver 'sr' needs updating - please use bus_type methods
[    1.354005] ata_piix 0000:00:1f.2: version 2.12
[    1.354016] ata_piix 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    1.354019] ata_piix 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
[    1.354055] ata_piix 0000:00:1f.2: setting latency timer to 64
[    1.354109] scsi0 : ata_piix
[    1.354165] scsi1 : ata_piix
[    1.355239] ata1: SATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xff90 irq 14
[    1.355243] ata2: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xff98 irq 15
[    2.148068] ata1.00: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[    2.148087] ata1.01: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[    2.190241] ata1.00: ATA-8: STM3500418AS, CC34, max UDMA/133
[    2.190245] ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    2.190294] ata1.01: ATAPI: ATAPI   iHAS322   8, 3L11, max UDMA/100
[    2.246263] ata1.00: configured for UDMA/133
[    2.260212] ata1.01: configured for UDMA/100
[    2.910674] ata2.00: SATA link down (SStatus 0 SControl 300)
[    2.910682] ata2.01: SATA link down (SStatus 0 SControl 300)
[    2.910761] scsi 0:0:0:0: Direct-Access     ATA      STM3500418AS     CC34 PQ: 0 ANSI: 5
[    2.910828] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors: (500 GB/465 GiB)
[    2.910840] sd 0:0:0:0: [sda] Write Protect is off
[    2.910842] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    2.910861] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.910906] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors: (500 GB/465 GiB)
[    2.910917] sd 0:0:0:0: [sda] Write Protect is off
[    2.910919] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[    2.910937] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.910939]  sda: sda1 sda2 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 >
[    3.020195] sd 0:0:0:0: [sda] Attached SCSI disk
[    3.020230] sd 0:0:0:0: Attached scsi generic sg0 type 0
[    3.021402] scsi 0:0:1:0: CD-ROM            ATAPI    iHAS322   8      3L11 PQ: 0 ANSI: 5
[    3.027306] sr0: scsi3-mmc drive: 16x/48x writer dvd-ram cd/rw xa/form2 cdda tray
[    3.027310] Uniform CD-ROM driver Revision: 3.20
[    3.027401] sr 0:0:1:0: Attached scsi CD-ROM sr0
[    3.027426] sr 0:0:1:0: Attached scsi generic sg1 type 5
[    3.027440] ata_piix 0000:00:1f.5: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    3.027443] ata_piix 0000:00:1f.5: MAP [ P0 -- P1 -- ]
[    3.027473] ata_piix 0000:00:1f.5: setting latency timer to 64
[    3.027515] scsi2 : ata_piix
[    3.027559] scsi3 : ata_piix
[    3.028452] ata3: SATA max UDMA/133 cmd 0x9c00 ctl 0x9880 bmdma 0x9400 irq 19
[    3.028456] ata4: SATA max UDMA/133 cmd 0x9800 ctl 0x9480 bmdma 0x9408 irq 19
[    3.354658] ata3: SATA link down (SStatus 0 SControl 300)
[    3.682658] ata4: SATA link down (SStatus 0 SControl 300)
[    3.682941] pata_jmicron 0000:04:00.0: PCI INT A -> GSI 17 (level, low) -> IRQ 17
[    3.682965] pata_jmicron 0000:04:00.0: setting latency timer to 64
[    3.683010] scsi4 : pata_jmicron
[    3.683048] scsi5 : pata_jmicron
[    3.683078] ata5: PATA max UDMA/100 cmd 0xdc00 ctl 0xd880 bmdma 0xd400 irq 17
[    3.683080] ata6: PATA max UDMA/100 cmd 0xd800 ctl 0xd480 bmdma 0xd408 irq 17
[    3.992297] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    3.992312] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    3.992326] ehci_hcd 0000:00:1a.7: setting latency timer to 64
[    3.992329] ehci_hcd 0000:00:1a.7: EHCI Host Controller
[    3.992370] ehci_hcd 0000:00:1a.7: new USB bus registered, assigned bus number 1
[    3.996265] ehci_hcd 0000:00:1a.7: debug port 1
[    3.996270] ehci_hcd 0000:00:1a.7: cache line size of 32 is not supported
[    3.996281] ehci_hcd 0000:00:1a.7: irq 18, io mem 0xf9fffc00
[    4.012013] ehci_hcd 0000:00:1a.7: USB 2.0 started, EHCI 1.00
[    4.012097] usb usb1: configuration #1 chosen from 1 choice
[    4.012116] hub 1-0:1.0: USB hub found
[    4.012122] hub 1-0:1.0: 6 ports detected
[    4.012199] ehci_hcd 0000:00:1d.7: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    4.012206] ehci_hcd 0000:00:1d.7: setting latency timer to 64
[    4.012209] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[    4.012240] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 2
[    4.016131] ehci_hcd 0000:00:1d.7: debug port 1
[    4.016136] ehci_hcd 0000:00:1d.7: cache line size of 32 is not supported
[    4.016145] ehci_hcd 0000:00:1d.7: irq 23, io mem 0xf9fff800
[    4.028013] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
[    4.028087] usb usb2: configuration #1 chosen from 1 choice
[    4.028105] hub 2-0:1.0: USB hub found
[    4.028111] hub 2-0:1.0: 6 ports detected
[    4.028181] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    4.028193] uhci_hcd: USB Universal Host Controller Interface driver
[    4.028208] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    4.028212] uhci_hcd 0000:00:1a.0: setting latency timer to 64
[    4.028215] uhci_hcd 0000:00:1a.0: UHCI Host Controller
[    4.028248] uhci_hcd 0000:00:1a.0: new USB bus registered, assigned bus number 3
[    4.028273] uhci_hcd 0000:00:1a.0: irq 16, io base 0x0000ac00
[    4.028326] usb usb3: configuration #1 chosen from 1 choice
[    4.028345] hub 3-0:1.0: USB hub found
[    4.028350] hub 3-0:1.0: 2 ports detected
[    4.028410] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 21 (level, low) -> IRQ 21
[    4.028414] uhci_hcd 0000:00:1a.1: setting latency timer to 64
[    4.028416] uhci_hcd 0000:00:1a.1: UHCI Host Controller
[    4.028448] uhci_hcd 0000:00:1a.1: new USB bus registered, assigned bus number 4
[    4.028472] uhci_hcd 0000:00:1a.1: irq 21, io base 0x0000a880
[    4.028527] usb usb4: configuration #1 chosen from 1 choice
[    4.028546] hub 4-0:1.0: USB hub found
[    4.028552] hub 4-0:1.0: 2 ports detected
[    4.028614] uhci_hcd 0000:00:1a.2: PCI INT D -> GSI 19 (level, low) -> IRQ 19
[    4.028618] uhci_hcd 0000:00:1a.2: setting latency timer to 64
[    4.028620] uhci_hcd 0000:00:1a.2: UHCI Host Controller
[    4.028655] uhci_hcd 0000:00:1a.2: new USB bus registered, assigned bus number 5
[    4.028673] uhci_hcd 0000:00:1a.2: irq 19, io base 0x0000a800
[    4.028725] usb usb5: configuration #1 chosen from 1 choice
[    4.028743] hub 5-0:1.0: USB hub found
[    4.028750] hub 5-0:1.0: 2 ports detected
[    4.028810] uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 23 (level, low) -> IRQ 23
[    4.028814] uhci_hcd 0000:00:1d.0: setting latency timer to 64
[    4.028816] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[    4.028848] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 6
[    4.028867] uhci_hcd 0000:00:1d.0: irq 23, io base 0x0000a480
[    4.028920] usb usb6: configuration #1 chosen from 1 choice
[    4.028938] hub 6-0:1.0: USB hub found
[    4.028943] hub 6-0:1.0: 2 ports detected
[    4.029001] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
[    4.029005] uhci_hcd 0000:00:1d.1: setting latency timer to 64
[    4.029008] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[    4.029039] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 7
[    4.029058] uhci_hcd 0000:00:1d.1: irq 19, io base 0x0000a400
[    4.029109] usb usb7: configuration #1 chosen from 1 choice
[    4.029127] hub 7-0:1.0: USB hub found
[    4.029131] hub 7-0:1.0: 2 ports detected
[    4.029195] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
[    4.029199] uhci_hcd 0000:00:1d.2: setting latency timer to 64
[    4.029202] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[    4.029231] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 8
[    4.029249] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000a080
[    4.029300] usb usb8: configuration #1 chosen from 1 choice
[    4.029320] hub 8-0:1.0: USB hub found
[    4.029326] hub 8-0:1.0: 2 ports detected
[    4.029419] usbcore: registered new interface driver libusual
[    4.029441] usbcore: registered new interface driver usbserial
[    4.029449] USB Serial support registered for generic
[    4.029463] usbcore: registered new interface driver usbserial_generic
[    4.029464] usbserial: USB Serial Driver core
[    4.029505] PNP: No PS/2 controller found. Probing ports directly.
[    4.029782] serio: i8042 KBD port at 0x60,0x64 irq 1
[    4.029786] serio: i8042 AUX port at 0x60,0x64 irq 12
[    4.032557] mice: PS/2 mouse device common for all mice
[    4.044586] rtc_cmos 00:03: RTC can wake from S4
[    4.044610] rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
[    4.044630] rtc0: alarms up to one month, y3k, 114 bytes nvram
[    4.044673] device-mapper: uevent: version 1.0.3
[    4.044737] device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@redhat.com
[    4.044788] device-mapper: multipath: version 1.0.5 loaded
[    4.044790] device-mapper: multipath round-robin: version 1.0.0 loaded
[    4.044844] EISA: Probing bus 0 at eisa.0
[    4.044868] EISA: Detected 0 cards.
[    4.044902] cpuidle: using governor ladder
[    4.044903] cpuidle: using governor menu
[    4.045281] TCP cubic registered
[    4.045355] NET: Registered protocol family 10
[    4.045678] lo: Disabled Privacy Extensions
[    4.045923] NET: Registered protocol family 17
[    4.045935] Bluetooth: L2CAP ver 2.11
[    4.045937] Bluetooth: L2CAP socket layer initialized
[    4.045939] Bluetooth: SCO (Voice Link) ver 0.6
[    4.045940] Bluetooth: SCO socket layer initialized
[    4.045961] Bluetooth: RFCOMM socket layer initialized
[    4.045965] Bluetooth: RFCOMM TTY layer initialized
[    4.045966] Bluetooth: RFCOMM ver 1.10
[    4.046006] Using IPI No-Shortcut mode
[    4.046057] registered taskstats version 1
[    4.046159]   Magic number: 5:777:986
[    4.046213] rtc_cmos 00:03: setting system clock to 2009-08-14 12:57:22 UTC (1250254642)
[    4.046216] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found
[    4.046217] EDD information not available.
[    4.046422] Freeing unused kernel memory: 532k freed
[    4.046511] Write protecting the kernel text: 4128k
[    4.046544] Write protecting the kernel read-only data: 1532k
[    4.095591] vesafb: framebuffer at 0xfb000000, mapped to 0xf7d00000, using 6144k, total 14336k
[    4.095593] vesafb: mode is 1024x768x32, linelength=4096, pages=1
[    4.095595] vesafb: protected mode interface info at c000:af30
[    4.095597] vesafb: pmi: set display start = c00caf93, set palette = c00cafee
[    4.095598] vesafb: pmi: ports = 3b4 3b5 3ba 3c0 3c1 3c4 3c5 3c6 3c7 3c8 3c9 3cc 3ce 3cf 3d0 3d1 3d2 3d3 3d4 3d5 3da
[    4.095607] vesafb: scrolling: redraw
[    4.095609] vesafb: Truecolor: size=8:8:8:8, shift=24:16:8:0
[    4.095672] Console: switching to colour frame buffer device 128x48
[    4.127252] fb0: VESA VGA frame buffer device
[    4.264102] Floppy drive(s): fd0 is 1.44M
[    4.283653] FDC 0 is a post-1991 82077
[    4.297612] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[    4.297627] r8169 0000:03:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[    4.297643] r8169 0000:03:00.0: setting latency timer to 64
[    4.297739] r8169 0000:03:00.0: irq 2299 for MSI/MSI-X
[    4.298223] eth0: RTL8168c/8111c at 0xf7c58000, 00:e0:4d:a4:cb:9d, XID 3c4000c0 IRQ 2299
[    4.708025] usb 3-2: new full speed USB device using uhci_hcd and address 2
[    4.863548] usb 3-2: configuration #1 chosen from 1 choice
[    5.104018] usb 4-1: new low speed USB device using uhci_hcd and address 2
[    5.355630] usb 4-1: configuration #1 chosen from 1 choice
[    5.365305] usbcore: registered new interface driver hiddev
[    5.408761] input:   USB Keyboard as /devices/pci0000:00/0000:00:1a.1/usb4/4-1/4-1:1.0/input/input3
[    5.408877] generic-usb 0003:1241:1603.0001: input,hidraw0: USB HID v1.10 Keyboard [  USB Keyboard] on usb-0000:00:1a.1-1/input0
[    5.495632] input:   USB Keyboard as /devices/pci0000:00/0000:00:1a.1/usb4/4-1/4-1:1.1/input/input4
[    5.497002] generic-usb 0003:1241:1603.0002: input,hidraw1: USB HID v1.10 Device [  USB Keyboard] on usb-0000:00:1a.1-1/input1
[    5.497015] usbcore: registered new interface driver usbhid
[    5.497018] usbhid: v2.6:USB HID core driver
[    5.600020] usb 4-2: new low speed USB device using uhci_hcd and address 3
[    5.768644] usb 4-2: configuration #1 chosen from 1 choice
[    5.786781] input: USB Optical Mouse as /devices/pci0000:00/0000:00:1a.1/usb4/4-2/4-2:1.0/input/input5
[    5.788867] generic-usb 0003:192F:0416.0003: input,hidraw2: USB HID v1.11 Mouse [USB Optical Mouse] on usb-0000:00:1a.1-2/input0
[    9.807600] kjournald starting.  Commit interval 5 seconds
[    9.807607] EXT3-fs: mounted filesystem with ordered data mode.
[   13.125496] udev: starting version 141
[   13.240182] parport_pc 00:08: reported by Plug and Play ACPI
[   13.240224] parport0: PC-style at 0x378, irq 7 [PCSPP]
[   13.256834] Linux agpgart interface v0.103
[   13.263859] iTCO_vendor_support: vendor-support=0
[   13.863996] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.05
[   13.864220] iTCO_wdt: Found a ICH10 TCO device (Version=2, TCOBASE=0x0860)
[   13.864288] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[   14.036723] nvidia: module license 'NVIDIA' taints kernel.
[   14.288609] nvidia 0000:01:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
[   14.288616] nvidia 0000:01:00.0: setting latency timer to 64
[   14.289431] NVRM: loading NVIDIA UNIX x86 Kernel Module  180.44  Mon Mar 23 14:59:10 PST 2009
[   14.569642] Bluetooth: Generic Bluetooth USB driver ver 0.3
[   14.569730] usbcore: registered new interface driver btusb
[   14.603399] ppdev: user-space parallel port driver
[   14.610197] input: PC Speaker as /devices/platform/pcspkr/input/input6
[   14.654174] Linux video capture interface: v2.00
[   14.696623] saa7134: `3;tuner=2' invalid for parameter `card'
[   14.706683] saa7134: `3;tuner=2' invalid for parameter `card'
[   14.767836] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[   14.767905] HDA Intel 0000:00:1b.0: setting latency timer to 64
[   14.797916] hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...
[   14.925443] lp0: using parport0 (interrupt-driven).
[   15.312562] EXT3 FS on sda9, internal journal
[   15.725132] type=1505 audit(1250238454.178:2): operation="profile_load" name="/usr/share/gdm/guest-session/Xsession" name2="default" pid=2185
[   15.759184] type=1505 audit(1250238454.210:3): operation="profile_load" name="/sbin/dhclient-script" name2="default" pid=2189
[   15.759264] type=1505 audit(1250238454.210:4): operation="profile_load" name="/sbin/dhclient3" name2="default" pid=2189
[   15.759296] type=1505 audit(1250238454.210:5): operation="profile_load" name="/usr/lib/NetworkManager/nm-dhcp-client.action" name2="default" pid=2189
[   15.759324] type=1505 audit(1250238454.210:6): operation="profile_load" name="/usr/lib/connman/scripts/dhclient-script" name2="default" pid=2189
[   15.854099] type=1505 audit(1250238454.306:7): operation="profile_load" name="/usr/lib/cups/backend/cups-pdf" name2="default" pid=2194
[   15.854238] type=1505 audit(1250238454.306:8): operation="profile_load" name="/usr/sbin/cupsd" name2="default" pid=2194
[   15.875111] type=1505 audit(1250238454.326:9): operation="profile_load" name="/usr/sbin/mysqld-akonadi" name2="default" pid=2198
[   15.894312] type=1505 audit(1250238454.346:10): operation="profile_load" name="/usr/sbin/tcpdump" name2="default" pid=2202
[   18.823973] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   18.823976] Bluetooth: BNEP filters: protocol multicast
[   18.830899] Bridge firewalling registered
[   23.546652] r8169: eth0: link up
[   23.546657] r8169: eth0: link up
[   33.319734] UDF-fs: No VRS found
[   33.404034] ISO 9660 Extensions: Microsoft Joliet Level 3
[   33.553876] ISOFS: changing to secondary root
[   34.236012] eth0: no IPv6 routers present
[   96.462836] NET: Registered protocol family 24
این کارهایی رو هم که شما گفتید همه رو امتحان کردم نمیشه

[blue2006]

سلام کارت tv منم saa7134  هست . تو پارسیکس مشکلی نداشتم برا نصیش ولی تو ubunto به مشکل برخوردم .
هنگام شناسایی کارت وقتی دستور  rmmod saa7134 رو می زنم با ارور زیر مواجه می شم . تو تاپیک هم گشتم ولی جواب درست و حسابی براش پیدا نکردم .ممنون می شم راهنمایی کنید .
ERROR: Module saa7134 is in use by saa7134_alsa
در ضمن صفحه tv time هم سیاه و روی dificalt هست . صداهم به استریو و ... تغییر نمی کنه .

[Freeman]

سلام کارت tv منم saa7134  هست . تو پارسیکس مشکلی نداشتم برا نصیش ولی تو ubunto به مشکل برخوردم .
هنگام شناسایی کارت وقتی دستور  rmmod saa7134 رو می زنم با ارور زیر مواجه می شم . تو تاپیک هم گشتم ولی جواب درست و حسابی براش پیدا نکردم .ممنون می شم راهنمایی کنید .
ERROR: Module saa7134 is in use by saa7134_alsa
در ضمن صفحه tv time هم سیاه و روی dificalt هست . صداهم به استریو و ... تغییر نمی کنه .

اون راه داره منم یکی از اون کارتهای دارم  کاش ابتدا جستجو میکردین

http://wiki.kde-ir.org/index.php?title=Tv

موفق باشید

[blue2006]

ببخشیدا یه سوال دیگه
من یه کپچر دیگه رو که می خوام نصب کنم . همه مراحل رو ادامه می دم مثل کپچر خودم . ولی وقتی tvtime رو باز می کنم یه صفحه آبی میاد و هرچی این کانال اون کانال می کنم و هرچی اسکن می زنم به جواب نمی رسم .
ظاهران کارت رو شناخته و همه گزینه هاش فعالن ولی نمی دون چرا تصویر ندارم .
هر دو تا کارت چیپ فلیپس هستند و saa7130 , saa7134  هستند .
یه راهنمایی سرعتی می خوام .

[blue2006]

اینم خروجی lspci

کد: [انتخاب]

jabireh@jabireh-desktop:~$ lspci

00:00.0 RAM memory: nVidia Corporation MCP65 Memory Controller (rev a3)

00:01.0 ISA bridge: nVidia Corporation MCP65 LPC Bridge (rev a3)

00:01.1 SMBus: nVidia Corporation MCP65 SMBus (rev a1)

00:01.2 RAM memory: nVidia Corporation MCP65 Memory Controller (rev a1)

00:02.0 USB Controller: nVidia Corporation MCP65 USB Controller (rev a3)

00:02.1 USB Controller: nVidia Corporation MCP65 USB Controller (rev a3)

00:07.0 Audio device: nVidia Corporation MCP65 High Definition Audio (rev a1)

00:08.0 PCI bridge: nVidia Corporation MCP65 PCI bridge (rev a1)

00:09.0 IDE interface: nVidia Corporation MCP65 IDE (rev a1)

00:0a.0 IDE interface: nVidia Corporation MCP65 SATA Controller (rev a3)

00:0b.0 PCI bridge: nVidia Corporation Device 045b (rev a1)

00:0c.0 PCI bridge: nVidia Corporation MCP65 PCI Express bridge (rev a1)

00:0d.0 PCI bridge: nVidia Corporation MCP65 PCI Express bridge (rev a1)

00:0e.0 PCI bridge: nVidia Corporation MCP65 PCI Express bridge (rev a1)

00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration

00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map

00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller

00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control

01:09.0 Communication controller: Conexant Systems, Inc. SoftV92 SpeakerPhone SoftRing Modem with SmartSP (rev 01)

01:0a.0 Multimedia controller: Philips Semiconductors SAA7134/SAA7135HL Video Broadcast Decoder (rev 01)

03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01)

04:00.0 VGA compatible controller: nVidia Corporation G72 [GeForce 7300 SE/7200 GS] (rev a1)

jabireh@jabireh-desktop:~$


اینم خروجی dmesg

کد: [انتخاب]

rved

[    0.204155] system 00:09: iomem range 0xfee00000-0xfee00fff has been reserved

[    0.204160] system 00:0b: ioport range 0xa00-0xa0f has been reserved

[    0.204162] system 00:0b: ioport range 0xa10-0xa1f has been reserved

[    0.204167] system 00:0c: iomem range 0xe0000000-0xefffffff has been reserved

[    0.204171] system 00:0d: iomem range 0x0-0x9ffff could not be reserved

[    0.204174] system 00:0d: iomem range 0xc0000-0xcffff could not be reserved

[    0.204177] system 00:0d: iomem range 0xe0000-0xfffff could not be reserved

[    0.204179] system 00:0d: iomem range 0x100000-0xbfffffff could not be reserved

[    0.204182] system 00:0d: iomem range 0xfec00000-0xffffffff could not be reserved

[    0.238841] AppArmor: AppArmor Filesystem Enabled

[    0.238870] pci 0000:00:08.0: PCI bridge, secondary bus 0000:01

[    0.238873] pci 0000:00:08.0:   IO window: 0xd000-0xdfff

[    0.238877] pci 0000:00:08.0:   MEM window: 0xfbe00000-0xfbefffff

[    0.238880] pci 0000:00:08.0:   PREFETCH window: disabled

[    0.238883] pci 0000:00:0b.0: PCI bridge, secondary bus 0000:02

[    0.238884] pci 0000:00:0b.0:   IO window: disabled

[    0.238887] pci 0000:00:0b.0:   MEM window: disabled

[    0.238889] pci 0000:00:0b.0:   PREFETCH window: disabled

[    0.238891] pci 0000:00:0c.0: PCI bridge, secondary bus 0000:03

[    0.238893] pci 0000:00:0c.0:   IO window: 0xe000-0xefff

[    0.238896] pci 0000:00:0c.0:   MEM window: 0xfbf00000-0xfbffffff

[    0.238898] pci 0000:00:0c.0:   PREFETCH window: disabled

[    0.238901] pci 0000:00:0d.0: PCI bridge, secondary bus 0000:04

[    0.238903] pci 0000:00:0d.0:   IO window: disabled

[    0.238905] pci 0000:00:0d.0:   MEM window: 0xfc000000-0xfebfffff

[    0.238908] pci 0000:00:0d.0:   PREFETCH window: 0x000000d0000000-0x000000dfffffff

[    0.238912] pci 0000:00:0e.0: PCI bridge, secondary bus 0000:05

[    0.238913] pci 0000:00:0e.0:   IO window: disabled

[    0.238916] pci 0000:00:0e.0:   MEM window: disabled

[    0.238918] pci 0000:00:0e.0:   PREFETCH window: disabled

[    0.238926] pci 0000:00:08.0: setting latency timer to 64

[    0.238930] pci 0000:00:0b.0: setting latency timer to 64

[    0.238934] pci 0000:00:0c.0: setting latency timer to 64

[    0.238938] pci 0000:00:0d.0: setting latency timer to 64

[    0.238941] pci 0000:00:0e.0: setting latency timer to 64

[    0.238946] pci_bus 0000:00: resource 0 io:  [0x00-0xffff]

[    0.238948] pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]

[    0.238950] pci_bus 0000:01: resource 0 io:  [0xd000-0xdfff]

[    0.238953] pci_bus 0000:01: resource 1 mem: [0xfbe00000-0xfbefffff]

[    0.238955] pci_bus 0000:01: resource 3 io:  [0x00-0xffff]

[    0.238957] pci_bus 0000:01: resource 4 mem: [0x000000-0xffffffff]

[    0.238960] pci_bus 0000:03: resource 0 io:  [0xe000-0xefff]

[    0.238962] pci_bus 0000:03: resource 1 mem: [0xfbf00000-0xfbffffff]

[    0.238964] pci_bus 0000:04: resource 1 mem: [0xfc000000-0xfebfffff]

[    0.238966] pci_bus 0000:04: resource 2 pref mem [0xd0000000-0xdfffffff]

[    0.239002] NET: Registered protocol family 2

[    0.239085] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)

[    0.239385] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)

[    0.240030] Switched to high resolution mode on CPU 0

[    0.240185] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)

[    0.240471] Switched to high resolution mode on CPU 1

[    0.240585] TCP: Hash tables configured (established 131072 bind 65536)

[    0.240588] TCP reno registered

[    0.240682] NET: Registered protocol family 1

[    0.240749] Trying to unpack rootfs image as initramfs...

[    0.408836] Freeing initrd memory: 7463k freed

[    0.414910] cpufreq-nforce2: No nForce2 chipset.

[    0.414934] Scanning for low memory corruption every 60 seconds

[    0.415026] audit: initializing netlink socket (disabled)

[    0.415041] type=2000 audit(1258107465.412:1): initialized

[    0.422159] highmem bounce pool size: 64 pages

[    0.422164] HugeTLB registered 4 MB page size, pre-allocated 0 pages

[    0.423329] VFS: Disk quotas dquot_6.5.2

[    0.423381] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)

[    0.423885] fuse init (API version 7.12)

[    0.423951] msgmni has been set to 1679

[    0.424194] alg: No test for stdrng (krng)

[    0.424215] io scheduler noop registered

[    0.424217] io scheduler anticipatory registered

[    0.424218] io scheduler deadline registered

[    0.424253] io scheduler cfq registered (default)

[    0.445954] pci 0000:00:00.0: Found enabled HT MSI Mapping

[    0.445999] pci 0000:00:00.0: Found enabled HT MSI Mapping

[    0.446052] pci 0000:00:00.0: Found enabled HT MSI Mapping

[    0.446105] pci 0000:00:00.0: Found enabled HT MSI Mapping

[    0.446163] pci 0000:00:00.0: Found enabled HT MSI Mapping

[    0.446223] pci 0000:00:00.0: Found enabled HT MSI Mapping

[    0.446288] pci 0000:00:00.0: Found enabled HT MSI Mapping

[    0.446303] pci 0000:04:00.0: Boot video device

[    0.446383]   alloc irq_desc for 24 on node -1

[    0.446385]   alloc kstat_irqs on node -1

[    0.446393] pcieport-driver 0000:00:0b.0: irq 24 for MSI/MSI-X

[    0.446398] pcieport-driver 0000:00:0b.0: setting latency timer to 64

[    0.446456]   alloc irq_desc for 25 on node -1

[    0.446458]   alloc kstat_irqs on node -1

[    0.446462] pcieport-driver 0000:00:0c.0: irq 25 for MSI/MSI-X

[    0.446465] pcieport-driver 0000:00:0c.0: setting latency timer to 64

[    0.446520]   alloc irq_desc for 26 on node -1

[    0.446521]   alloc kstat_irqs on node -1

[    0.446525] pcieport-driver 0000:00:0d.0: irq 26 for MSI/MSI-X

[    0.446529] pcieport-driver 0000:00:0d.0: setting latency timer to 64

[    0.446581]   alloc irq_desc for 27 on node -1

[    0.446583]   alloc kstat_irqs on node -1

[    0.446586] pcieport-driver 0000:00:0e.0: irq 27 for MSI/MSI-X

[    0.446590] pcieport-driver 0000:00:0e.0: setting latency timer to 64

[    0.446636] pci_hotplug: PCI Hot Plug PCI Core version: 0.5

[    0.446658] pciehp: PCI Express Hot Plug Controller Driver version: 0.4

[    0.446767] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0

[    0.446770] ACPI: Power Button [PWRF]

[    0.446820] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1

[    0.446826] ACPI: Power Button [PWRB]

[    0.447031] processor LNXCPU:00: registered as cooling_device0

[    0.447059] processor LNXCPU:01: registered as cooling_device1

[    0.449537] isapnp: Scanning for PnP cards...

[    0.802303] isapnp: No Plug & Play device found

[    0.803229] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled

[    0.803325] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A

[    0.803536] 00:04: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A

[    0.804447] brd: module loaded

[    0.804827] loop: module loaded

[    0.804889] input: Macintosh mouse button emulation as /devices/virtual/input/input2

[    0.804957] ahci 0000:00:0a.0: version 3.0

[    0.805278] ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 23

[    0.805282]   alloc irq_desc for 23 on node -1

[    0.805284]   alloc kstat_irqs on node -1

[    0.805294] ahci 0000:00:0a.0: PCI INT A -> Link[LSA0] -> GSI 23 (level, low) -> IRQ 23

[    0.805320]   alloc irq_desc for 28 on node -1

[    0.805321]   alloc kstat_irqs on node -1

[    0.805328] ahci 0000:00:0a.0: irq 28 for MSI/MSI-X

[    0.805393] ahci 0000:00:0a.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl IDE mode

[    0.805396] ahci 0000:00:0a.0: flags: 64bit ncq sntf pm led clo pmp pio

[    0.805399] ahci 0000:00:0a.0: setting latency timer to 64

[    0.805887] scsi0 : ahci

[    0.806017] scsi1 : ahci

[    0.806074] scsi2 : ahci

[    0.806138] scsi3 : ahci

[    0.806238] ata1: SATA max UDMA/133 abar m8192@0xfbdfc000 port 0xfbdfc100 irq 28

[    0.806240] ata2: SATA max UDMA/133 abar m8192@0xfbdfc000 port 0xfbdfc180 irq 28

[    0.806243] ata3: SATA max UDMA/133 abar m8192@0xfbdfc000 port 0xfbdfc200 irq 28

[    0.806245] ata4: SATA max UDMA/133 irq_stat 0x00400040, connection status changed irq 28

[    0.806450] pata_amd 0000:00:09.0: version 0.4.1

[    0.806495] pata_amd 0000:00:09.0: setting latency timer to 64

[    0.806572] scsi4 : pata_amd

[    0.806625] scsi5 : pata_amd

[    0.807693] ata5: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14

[    0.807695] ata6: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15

[    0.808325] Fixed MDIO Bus: probed

[    0.808354] PPP generic driver version 2.4.2

[    0.808461] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

[    0.808765] ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 22

[    0.808769]   alloc irq_desc for 22 on node -1

[    0.808771]   alloc kstat_irqs on node -1

[    0.808780] ehci_hcd 0000:00:02.1: PCI INT B -> Link[LUB2] -> GSI 22 (level, low) -> IRQ 22

[    0.808793] ehci_hcd 0000:00:02.1: setting latency timer to 64

[    0.808796] ehci_hcd 0000:00:02.1: EHCI Host Controller

[    0.808848] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1

[    0.808874] ehci_hcd 0000:00:02.1: debug port 1

[    0.808878] ehci_hcd 0000:00:02.1: cache line size of 64 is not supported

[    0.808896] ehci_hcd 0000:00:02.1: irq 22, io mem 0xfbdfec00

[    0.820015] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00

[    0.820083] usb usb1: configuration #1 chosen from 1 choice

[    0.820109] hub 1-0:1.0: USB hub found

[    0.820117] hub 1-0:1.0: 10 ports detected

[    0.820175] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver

[    0.820456] ACPI: PCI Interrupt Link [LUB0] enabled at IRQ 21

[    0.820459]   alloc irq_desc for 21 on node -1

[    0.820461]   alloc kstat_irqs on node -1

[    0.820468] ohci_hcd 0000:00:02.0: PCI INT A -> Link[LUB0] -> GSI 21 (level, low) -> IRQ 21

[    0.820474] ohci_hcd 0000:00:02.0: setting latency timer to 64

[    0.820477] ohci_hcd 0000:00:02.0: OHCI Host Controller

[    0.820509] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2

[    0.820531] ohci_hcd 0000:00:02.0: irq 21, io mem 0xfbdff000

[    0.878057] usb usb2: configuration #1 chosen from 1 choice

[    0.878078] hub 2-0:1.0: USB hub found

[    0.878086] hub 2-0:1.0: 10 ports detected

[    0.878139] uhci_hcd: USB Universal Host Controller Interface driver

[    0.878214] PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1

[    0.878216] PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp

[    0.878600] serio: i8042 KBD port at 0x60,0x64 irq 1

[    0.878656] mice: PS/2 mouse device common for all mice

[    0.878749] rtc_cmos 00:08: RTC can wake from S4

[    0.878780] rtc_cmos 00:08: rtc core: registered rtc_cmos as rtc0

[    0.878813] rtc0: alarms up to one year, y3k, 114 bytes nvram

[    0.878909] device-mapper: uevent: version 1.0.3

[    0.879007] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com

[    0.879104] device-mapper: multipath: version 1.1.0 loaded

[    0.879106] device-mapper: multipath round-robin: version 1.0.0 loaded

[    0.879247] EISA: Probing bus 0 at eisa.0

[    0.879254] Cannot allocate resource for EISA slot 2

[    0.879270] EISA: Detected 0 cards.

[    0.879420] cpuidle: using governor ladder

[    0.879422] cpuidle: using governor menu

[    0.879814] TCP cubic registered

[    0.879958] NET: Registered protocol family 10

[    0.880348] lo: Disabled Privacy Extensions

[    0.880592] NET: Registered protocol family 17

[    0.880608] Bluetooth: L2CAP ver 2.13

[    0.880609] Bluetooth: L2CAP socket layer initialized

[    0.880612] Bluetooth: SCO (Voice Link) ver 0.6

[    0.880613] Bluetooth: SCO socket layer initialized

[    0.880649] Bluetooth: RFCOMM TTY layer initialized

[    0.880652] Bluetooth: RFCOMM socket layer initialized

[    0.880653] Bluetooth: RFCOMM ver 1.11

[    0.880675] powernow-k8: Found 1 AMD Athlon(tm) 64 X2 Dual Core Processor 5200+ processors (2 cpu cores) (version 2.20.00)

[    0.880684] [Firmware Bug]: powernow-k8: No compatible ACPI _PSS objects found.

[    0.880685] [Firmware Bug]: powernow-k8: Try again with latest BIOS.

[    0.880706] Using IPI No-Shortcut mode

[    0.880757] PM: Resume from disk failed.

[    0.880769] registered taskstats version 1

[    0.880878]   Magic number: 1:785:274

[    0.880909] tty tty11: hash matches

[    0.880986] rtc_cmos 00:08: setting system clock to 2009-11-13 10:17:46 UTC (1258107466)

[    0.880989] BIOS EDD facility v0.16 2004-Jun-25, 0 devices found

[    0.880990] EDD information not available.

[    0.904986] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3

[    0.996286] ata5.00: ATAPI: SONY    CD-RW  CRX320EE, RYK4, max UDMA/33

[    0.996310] ata5.01: ATAPI: TSSTcorp CDDVDW SH-S202J, SB01, max UDMA/66

[    0.996330] ata5: nv_mode_filter: 0x739f&0x739f->0x739f, BIOS=0x7000 (0xc0c50000) ACPI=0x701f (60:30:0x15)

[    0.996334] ata5: nv_mode_filter: 0x1f39f&0x1f39f->0x1f39f, BIOS=0x1f000 (0xc0c50000) ACPI=0x1f01f (60:30:0x15)

[    1.028237] ata5.00: configured for UDMA/33

[    1.044232] ata5.01: configured for UDMA/66

[    1.124022] ata2: SATA link down (SStatus 0 SControl 300)

[    1.124032] ata3: SATA link down (SStatus 0 SControl 300)

[    1.124038] ata1: SATA link down (SStatus 0 SControl 300)

[    1.132021] usb 1-1: new high speed USB device using ehci_hcd and address 2

[    1.360048] usb 1-1: device descriptor read/all, error -71

[    1.476020] usb 1-1: new high speed USB device using ehci_hcd and address 3

[    1.696020] ata4: SATA link up 3.0 Gbps (SStatus 123 SControl 300)

[    1.696983] ata4.00: ATA-8: STM3500418AS, CC37, max UDMA/133

[    1.696985] ata4.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)

[    1.698131] ata4.00: configured for UDMA/133

[    1.712115] scsi 3:0:0:0: Direct-Access     ATA      STM3500418AS     CC37 PQ: 0 ANSI: 5

[    1.712220] sd 3:0:0:0: Attached scsi generic sg0 type 0

[    1.712252] sd 3:0:0:0: [sda] 976773168 512-byte logical blocks: (500 GB/465 GiB)

[    1.712287] sd 3:0:0:0: [sda] Write Protect is off

[    1.712289] sd 3:0:0:0: [sda] Mode Sense: 00 3a 00 00

[    1.712308] sd 3:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA

[    1.712415]  sda:

[    1.713598] scsi 4:0:0:0: CD-ROM            SONY     CD-RW  CRX320EE  RYK4 PQ: 0 ANSI: 5

[    1.719364] sr0: scsi3-mmc drive: 0x/52x writer cd/rw xa/form2 cdda tray

[    1.719367] Uniform CD-ROM driver Revision: 3.20

[    1.719445] sr 4:0:0:0: Attached scsi CD-ROM sr0

[    1.719477] sr 4:0:0:0: Attached scsi generic sg1 type 5

[    1.720034] scsi 4:0:1:0: CD-ROM            TSSTcorp CDDVDW SH-S202J  SB01 PQ: 0 ANSI: 5

[    1.723513] sr1: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray

[    1.723570] sr 4:0:1:0: Attached scsi CD-ROM sr1

[    1.723600] sr 4:0:1:0: Attached scsi generic sg2 type 5

[    1.723635] ata6: port disabled. ignoring.

[    1.732033]  sda1 sda2 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 sda12 sda13 sda14 sda15 >

[    1.846062] sd 3:0:0:0: [sda] Attached SCSI disk

[    1.846091] Freeing unused kernel memory: 540k freed

[    1.846480] Write protecting the kernel text: 4568k

[    1.846511] Write protecting the kernel read-only data: 1836k

[    1.971014] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded

[    1.971321] ACPI: PCI Interrupt Link [LNEA] enabled at IRQ 19

[    1.971326]   alloc irq_desc for 19 on node -1

[    1.971328]   alloc kstat_irqs on node -1

[    1.971338] r8169 0000:03:00.0: PCI INT A -> Link[LNEA] -> GSI 19 (level, low) -> IRQ 19

[    1.971368] r8169 0000:03:00.0: setting latency timer to 64

[    1.971405]   alloc irq_desc for 29 on node -1

[    1.971406]   alloc kstat_irqs on node -1

[    1.971416] r8169 0000:03:00.0: irq 29 for MSI/MSI-X

[    1.971919] eth0: RTL8168b/8111b at 0xf8070000, 00:19:db:f6:65:64, XID 38000000 IRQ 29

[    1.974232] Floppy drive(s): fd0 is 1.44M

[    1.997215] FDC 0 is a post-1991 82077

[    2.053016] usb 1-1: device not accepting address 3, error -71

[    2.164031] usb 1-1: new high speed USB device using ehci_hcd and address 4

[    2.629020] usb 1-1: device not accepting address 4, error -71

[    2.741029] usb 1-1: new high speed USB device using ehci_hcd and address 5

[    3.225022] usb 1-1: device not accepting address 5, error -71

[    3.225042] hub 1-0:1.0: unable to enumerate USB device on port 1

[    3.346305] PM: Starting manual resume from disk

[    3.346310] PM: Resume from partition 8:13

[    3.346311] PM: Checking hibernation image.

[    3.346462] PM: Resume from disk failed.

[    3.356252] EXT4-fs (sda14): barriers enabled

[    3.363134] kjournald2 starting: pid 386, dev sda14:8, commit interval 5 seconds

[    3.363145] EXT4-fs (sda14): delayed allocation enabled

[    3.363147] EXT4-fs: file extents enabled

[    3.364863] EXT4-fs: mballoc enabled

[    3.364877] EXT4-fs (sda14): mounted filesystem with ordered data mode

[    3.528033] usb 1-5: new high speed USB device using ehci_hcd and address 8

[    3.664753] usb 1-5: configuration #1 chosen from 1 choice

[    3.670857] Initializing USB Mass Storage driver...

[    3.671034] scsi6 : SCSI emulation for USB Mass Storage devices

[    3.671164] usb-storage: device found at 8

[    3.671167] usb-storage: waiting for device to settle before scanning

[    3.671172] usbcore: registered new interface driver usb-storage

[    3.671175] USB Mass Storage support registered.

[    3.701028] type=1505 audit(1258107469.320:2): operation="profile_load" pid=409 name=/usr/share/gdm/guest-session/Xsession

[    3.703514] type=1505 audit(1258107469.320:3): operation="profile_load" pid=415 name=/sbin/dhclient3

[    3.703743] type=1505 audit(1258107469.320:4): operation="profile_load" pid=415 name=/usr/lib/NetworkManager/nm-dhcp-client.action

[    3.703873] type=1505 audit(1258107469.320:5): operation="profile_load" pid=415 name=/usr/lib/connman/scripts/dhclient-script

[    3.739423] type=1505 audit(1258107469.356:6): operation="profile_load" pid=416 name=/usr/bin/evince

[    3.743347] type=1505 audit(1258107469.360:7): operation="profile_load" pid=416 name=/usr/bin/evince-previewer

[    3.745658] type=1505 audit(1258107469.364:8): operation="profile_load" pid=416 name=/usr/bin/evince-thumbnailer

[    3.756728] type=1505 audit(1258107469.372:9): operation="profile_load" pid=418 name=/usr/lib/cups/backend/cups-pdf

[    3.757026] type=1505 audit(1258107469.376:10): operation="profile_load" pid=418 name=/usr/sbin/cupsd

[    4.097027] usb 2-1: new full speed USB device using ohci_hcd and address 2

[    4.168318] Adding 2931820k swap on /dev/sda13.  Priority:-1 extents:1 across:2931820k

[    4.297089] usb 2-1: not running at top speed; connect to a high speed hub

[    4.319169] usb 2-1: configuration #1 chosen from 1 choice

[    4.435593] udev: starting version 147

[    4.619522] EXT4-fs (sda14): internal journal on sda14:8

[    4.625038] usb 2-3: new full speed USB device using ohci_hcd and address 3

[    4.837165] usb 2-3: configuration #1 chosen from 1 choice

[    4.987707] k8temp 0000:00:18.3: Temperature readouts might be wrong - check erratum #141

[    5.015264] Linux agpgart interface v0.103

[    5.125025] usb 2-4: new low speed USB device using ohci_hcd and address 4

[    5.138973] i2c-adapter i2c-0: nForce2 SMBus adapter at 0x2d00

[    5.138991] i2c-adapter i2c-1: nForce2 SMBus adapter at 0x2e00

[    5.335172] usb 2-4: configuration #1 chosen from 1 choice

[    5.493684] EXT4-fs (sda15): barriers enabled

[    5.494156] kjournald2 starting: pid 692, dev sda15:8, commit interval 5 seconds

[    5.494746] EXT4-fs (sda15): internal journal on sda15:8

[    5.494750] EXT4-fs (sda15): delayed allocation enabled

[    5.494753] EXT4-fs: file extents enabled

[    5.496533] EXT4-fs: mballoc enabled

[    5.496548] EXT4-fs (sda15): mounted filesystem with ordered data mode

[    6.005660] nvidia: module license 'NVIDIA' taints kernel.

[    6.005663] Disabling lock debugging due to kernel taint

[    6.167820] parport_pc 00:06: reported by Plug and Play ACPI

[    6.167864] parport0: PC-style at 0x378, irq 7 [PCSPP]

[    6.201846] lp: driver loaded but no devices found

[    6.260247] ACPI: PCI Interrupt Link [LNED] enabled at IRQ 18

[    6.260253]   alloc irq_desc for 18 on node -1

[    6.260255]   alloc kstat_irqs on node -1

[    6.260266] nvidia 0000:04:00.0: PCI INT A -> Link[LNED] -> GSI 18 (level, low) -> IRQ 18

[    6.260273] nvidia 0000:04:00.0: setting latency timer to 64

[    6.260558] NVRM: loading NVIDIA UNIX x86 Kernel Module  190.42  Tue Oct 20 20:18:32 PDT 2009

[    6.265160] lp0: using parport0 (interrupt-driven).

[    6.307293] ip_tables: (C) 2000-2006 Netfilter Core Team

[    6.562613] __ratelimit: 3 callbacks suppressed

[    6.562617] type=1505 audit(1258094872.180:12): operation="profile_replace" pid=767 name=/usr/share/gdm/guest-session/Xsession

[    6.564158] type=1505 audit(1258094872.180:13): operation="profile_replace" pid=768 name=/sbin/dhclient3

[    6.564388] type=1505 audit(1258094872.180:14): operation="profile_replace" pid=768 name=/usr/lib/NetworkManager/nm-dhcp-client.action

[    6.564520] type=1505 audit(1258094872.180:15): operation="profile_replace" pid=768 name=/usr/lib/connman/scripts/dhclient-script

[    6.568764] type=1505 audit(1258094872.184:16): operation="profile_replace" pid=769 name=/usr/bin/evince

[    6.572747] type=1505 audit(1258094872.188:17): operation="profile_replace" pid=769 name=/usr/bin/evince-previewer

[    6.575051] type=1505 audit(1258094872.192:18): operation="profile_replace" pid=769 name=/usr/bin/evince-thumbnailer

[    6.579704] type=1505 audit(1258094872.196:19): operation="profile_replace" pid=771 name=/usr/lib/cups/backend/cups-pdf

[    6.579992] type=1505 audit(1258094872.196:20): operation="profile_replace" pid=771 name=/usr/sbin/cupsd

[    6.581771] type=1505 audit(1258094872.200:21): operation="profile_replace" pid=772 name=/usr/sbin/tcpdump

[    6.733420] ppdev: user-space parallel port driver

[    6.744155] usblp0: USB Bidirectional printer dev 2 if 0 alt 0 proto 2 vid 0x04A9 pid 0x2676

[    6.744176] usbcore: registered new interface driver usblp

[    6.834773] ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 17

[    6.834779]   alloc irq_desc for 17 on node -1

[    6.834781]   alloc kstat_irqs on node -1

[    6.834791] hsfpcibasic2 0000:01:09.0: PCI INT A -> Link[LNKB] -> GSI 17 (level, low) -> IRQ 17

[    6.844594] Linux video capture interface: v2.00

[    6.867021] usbcore: registered new interface driver hiddev

[    6.874387] input: USB Optical Mouse as /devices/pci0000:00/0000:00:02.0/usb2/2-4/2-4:1.0/input/input4

[    6.874464] generic-usb 0003:15CA:00C3.0001: input,hidraw0: USB HID v1.10 Mouse [USB Optical Mouse] on usb-0000:00:02.0-4/input0

[    6.874481] usbcore: registered new interface driver usbhid

[    6.874484] usbhid: v2.6:USB HID core driver

[    7.065758] saa7130/34: v4l2 driver version 0.2.15 loaded

[    7.261368] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 20

[    7.261374]   alloc irq_desc for 20 on node -1

[    7.261376]   alloc kstat_irqs on node -1

[    7.261386] HDA Intel 0000:00:07.0: PCI INT B -> Link[LAZA] -> GSI 20 (level, low) -> IRQ 20

[    7.261425] HDA Intel 0000:00:07.0: setting latency timer to 64

[    7.965030] hda_codec: Unknown model for ALC883, trying auto-probe from BIOS...

[    7.981115] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:07.0/input/input5

[    8.669224] usb-storage: device scan complete

[    8.671195] scsi 6:0:0:0: Direct-Access              USB FLASH DRIVE  PMAP PQ: 0 ANSI: 0 CCS

[    8.671527] sd 6:0:0:0: Attached scsi generic sg3 type 0

[    8.673567] sd 6:0:0:0: [sdb] 2015232 512-byte logical blocks: (1.03 GB/984 MiB)

[    8.675057] sd 6:0:0:0: [sdb] Write Protect is off

[    8.675059] sd 6:0:0:0: [sdb] Mode Sense: 23 00 00 00

[    8.675062] sd 6:0:0:0: [sdb] Assuming drive cache: write through

[    8.678057] sd 6:0:0:0: [sdb] Assuming drive cache: write through

[    8.678062]  sdb: sdb1

[    8.684062] sd 6:0:0:0: [sdb] Assuming drive cache: write through

[    8.684069] sd 6:0:0:0: [sdb] Attached SCSI removable disk

[    9.309884] ttySHSF0 at I/O 0xdc00 (irq = 17) is a Conexant HSF softmodem (PCI-14f1:2f30-14f1:205d)

[    9.310255] ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 16

[    9.310260]   alloc irq_desc for 16 on node -1

[    9.310262]   alloc kstat_irqs on node -1

[    9.310272] saa7134 0000:01:0a.0: PCI INT A -> Link[LNKC] -> GSI 16 (level, low) -> IRQ 16

[    9.310278] saa7134[0]: found at 0000:01:0a.0, rev: 1, irq: 16, latency: 64, mmio: 0xfbeefc00

[    9.310284] saa7134[0]: subsystem: 17de:7126, board: UNKNOWN/GENERIC [card=0,autodetected]

[    9.310298] saa7134[0]: board init: gpio is c0407f

[    9.310304] IRQ 16/saa7134[0]: IRQF_DISABLED is not guaranteed on shared IRQs

[    9.461016] saa7134[0]: i2c eeprom 00: de 17 26 71 10 28 ff ff ff ff ff ff ff ff ff ff

[    9.461025] saa7134[0]: i2c eeprom 10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff

[    9.461033] saa7134[0]: i2c eeprom 20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff

[    9.461040] saa7134[0]: i2c eeprom 30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff

[    9.461048] saa7134[0]: i2c eeprom 40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff

[    9.461055] saa7134[0]: i2c eeprom 50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff

[    9.461063] saa7134[0]: i2c eeprom 60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff

[    9.461070] saa7134[0]: i2c eeprom 70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff

[    9.461077] saa7134[0]: i2c eeprom 80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff

[    9.461085] saa7134[0]: i2c eeprom 90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff

[    9.461092] saa7134[0]: i2c eeprom a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff

[    9.461100] saa7134[0]: i2c eeprom b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff

[    9.461107] saa7134[0]: i2c eeprom c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff

[    9.461114] saa7134[0]: i2c eeprom d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff

[    9.461121] saa7134[0]: i2c eeprom e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff

[    9.461129] saa7134[0]: i2c eeprom f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff

[    9.461139] i2c-adapter i2c-2: Invalid 7-bit address 0x7a

[    9.461689] saa7134[0]: registered device video0 [v4l2]

[    9.461709] saa7134[0]: registered device vbi0

[    9.485813] saa7134_alsa: disagrees about version of symbol snd_pcm_new

[    9.485817] saa7134_alsa: Unknown symbol snd_pcm_new

[    9.486252] saa7134_alsa: disagrees about version of symbol snd_pcm_stop

[    9.486254] saa7134_alsa: Unknown symbol snd_pcm_stop

[    9.486838] saa7134_alsa: disagrees about version of symbol snd_pcm_lib_ioctl

[    9.486840] saa7134_alsa: Unknown symbol snd_pcm_lib_ioctl

[    9.487063] saa7134_alsa: disagrees about version of symbol snd_pcm_set_ops

[    9.487065] saa7134_alsa: Unknown symbol snd_pcm_set_ops

[    9.487294] saa7134_alsa: disagrees about version of symbol snd_pcm_hw_constraint_integer

[    9.487296] saa7134_alsa: Unknown symbol snd_pcm_hw_constraint_integer

[    9.487707] saa7134_alsa: disagrees about version of symbol snd_pcm_period_elapsed

[    9.487709] saa7134_alsa: Unknown symbol snd_pcm_period_elapsed

[    9.487781] saa7134_alsa: disagrees about version of symbol snd_pcm_hw_constraint_step

[    9.487783] saa7134_alsa: Unknown symbol snd_pcm_hw_constraint_step

[   10.535125] hsfpcibasic2 0000:01:09.0: PCI INT A disabled

[   10.614148] hsfpcibasic2 0000:01:09.0: PCI INT A -> Link[LNKB] -> GSI 17 (level, low) -> IRQ 17

[   10.969883] ttySHSF0 at I/O 0xdc00 (irq = 17) is a Conexant HSF softmodem (PCI-14f1:2f30-14f1:205d)

[   11.828856] usbcore: registered new interface driver hsfusbcd2

[   12.051719] r8169: eth0: link down

[   12.051901] ADDRCONF(NETDEV_UP): eth0: link is not ready

[   14.016905] usb 2-1: usbfs: interface 0 claimed by usblp while 'usb' sets config #1

[  300.742373] PPP BSD Compression module registered

[  300.749857] PPP Deflate Compression module registered

jabireh@jabireh-desktop:~$


[mrshadpoor]

آقا سلام
از راهنمایی تمام دوستان ممنونم
آقا من مشکلم اینکه پیام nosignal اومده ولی در قسمت video source جلوش هیچی ننوشته
یعنی صفحه آبی شده ولی ننوشته television 

آقا ممنون

[مهدی باقری]

سلام
با تشکراز راهنمایی تمام دوستان
آقا من مشکلم اینکه پیام nosignal اومده ولی در قسمت video source جلوش هیچی ننوشته
یعنی صفحه آبی شده ولی ننوشته television
مشکل منم نثله بعضی دوستان هستش mrshadpoor
اگر هر کسی تونست مشکلو حل کنه برا خودش اینجا بزاره بقیه هم استفاده کنیم