مشکل با مودم در اوبونتو 7.10

[Mehrdad-bx]

سلام دوستان
من یه مودم اینترنال یه چیپی(از همونایی که زیر سر بیل گیتسه) دارم: Creative Modem Blaster V.90 PCI DI5655 COM3
یه ماهی الاف بودم تا تونستم نصب و اکتیوش کنم(اگه اکتیو باشه)
حالا وقتی با gnome ppp میخواهم کانکت شم صدای شماره گیری برای اتصال میاد ولی روی یه نوشته گیر میکنه و کنکت نیست.
با pppconfig هم در terminal ارور میده .
راهی که برای نصبش رفتم دیوانه کننده بود، میشه کمکم کنید مودممو نصبش کنم؟

[سید مهدی]

اگه صدای شماره‌گیریش میاد یعنی مودم نصب هست. از صفحه اول gnome ppp وارد تنظیمات بشید و به سربرگ سوم برید و از اونجا قسمت carrier check رو بدون تیک و stupid mode رو تیک دار کنید و دوباره امتحان کنید بزنید به اینترنت وصل شه.

[pol100]

موقعه که setup اجرا می کنم این پیام میده

mahdi@mahdi-desktop:~/ess_2.6-v0.4$ ./setup
checking for running kernel version...2.6.22
make: Warning: File `Makefile-2.6.in' has modification time 2.9e+07 s in the future
make: warning: Clock skew detected. Your build may be incomplete.
checking for gcc...4.1.3
checking for kernel gcc version...4.1.3
searching for kernel includes...found at /lib/modules/2.6.22-14-generic/build/include
checking for autoconf.h...checking for kernel version in utsrelease.h...t.c:1:19: error: stdio.h: No such file or directory
t.c: In function ‘main’:
t.c:4: warning: incompatible implicit declaration of built-in function ‘printf’
./configure: line 360: ./t: No such file or directory
rm: cannot remove `./t': No such file or directory
** error
could not determine a proper UTS_RELEASE
** compilation error
please read the FAQ about reporting compilation problems
and report this problem. A transcript of the build process
has been saved in make.log. When reporting problems to
the development team, please send us this file.
mahdi@mahdi-desktop:~/ess_2.6-v0.4$
 

[Mehrdad-bx]

خیلی ممنون دوستان جواب داد و من الان از اوبونتو اینترنت ام

[سید مهدی]

موقعه که setup اجرا می کنم این پیام میده

mahdi@mahdi-desktop:~/ess_2.6-v0.4$ ./setup
checking for running kernel version...2.6.22
make: Warning: File `Makefile-2.6.in' has modification time 2.9e+07 s in the future
make: warning: Clock skew detected. Your build may be incomplete.
checking for gcc...4.1.3
checking for kernel gcc version...4.1.3
searching for kernel includes...found at /lib/modules/2.6.22-14-generic/build/include
checking for autoconf.h...checking for kernel version in utsrelease.h...t.c:1:19: error: stdio.h: No such file or directory
t.c: In function ‘main’:
t.c:4: warning: incompatible implicit declaration of built-in function ‘printf’
./configure: line 360: ./t: No such file or directory
rm: cannot remove `./t': No such file or directory
** error
could not determine a proper UTS_RELEASE
** compilation error
please read the FAQ about reporting compilation problems
and report this problem. A transcript of the build process
has been saved in make.log. When reporting problems to
the development team, please send us this file.
mahdi@mahdi-desktop:~/ess_2.6-v0.4$
 

مودم شما از چه نوعی هست ؟ ظاهر مراحل نصبش میخوره که smartlink باشه. اگه اینطوره، قبل از استفاده از این درایور برید CD اوبونتو رو بزارین توی دستگاه و دستور زیر رو اجرا کنید:

کد: [انتخاب]

sudo apt-get install sl-modem-daemon بعدش هم خروجی زیر رو برامون بزارین:

کد: [انتخاب]

wvdialconf

[pol100]

خروجی دستور            sudo apt-get install sl-modem-daemon

mahdi@mahdi-desktop:~$ sudo apt-get install sl-modem-daemon
[sudo] password for mahdi:
Reading package lists... Done
Building dependency tree       
Reading state information... Done
The following NEW packages will be installed:
  sl-modem-daemon
0 upgraded, 1 newly installed, 0 to remove and 0 not upgraded.
Need to get 0B/510kB of archives.
After unpacking 1163kB of additional disk space will be used.
Preconfiguring packages ...
tar: ./config: time stamp 2007-09-30 03:37:08 is 9581263.539087013 s in the future
tar: ./templates: time stamp 2007-09-30 03:37:08 is 9581263.537769731 s in the future
tar: ./postinst: time stamp 2007-09-30 03:37:09 is 9581264.53711123 s in the future
tar: ./prerm: time stamp 2007-09-30 03:37:10 is 9581265.536495194 s in the future
tar: ./postrm: time stamp 2007-09-30 03:37:10 is 9581265.535775788 s in the future
tar: ./conffiles: time stamp 2007-09-30 03:37:10 is 9581265.535116728 s in the future
tar: ./md5sums: time stamp 2007-09-30 03:37:10 is 9581265.534501531 s in the future
tar: ./control: time stamp 2007-09-30 03:37:10 is 9581265.533889407 s in the future
tar: .: time stamp 2007-09-30 03:37:10 is 9581265.533276165 s in the future
Selecting previously deselected package sl-modem-daemon.
(Reading database ... 88947 files and directories currently installed.)
Unpacking sl-modem-daemon (from .../sl-modem-daemon_2.9.10+2.9.9d+e-pre2-5ubuntu4_i386.deb) ...
Setting up sl-modem-daemon (2.9.10+2.9.9d+e-pre2-5ubuntu4) ...
Adding system user `Slmodemd' (UID 109) ...
Adding new group `Slmodemd' (GID 120) ...
Adding new user `Slmodemd' (UID 109) with group `Slmodemd' ...
Not creating home directory `/'.
FATAL: Module ungrab_winmodem not found.
FATAL: Module slamr not found.
Starting SmartLink Modem driver for: auto.
Creating /dev/modem symlink, pointing to: /dev/ttySL0.

mahdi@mahdi-desktop:~$


wvdialconf

=========================================================================

mahdi@mahdi-desktop:~$ sudo apt-get install sl-modem-daemon
[sudo] password for mahdi:
Reading package lists... Done
Building dependency tree       
Reading state information... Done
The following NEW packages will be installed:
  sl-modem-daemon
0 upgraded, 1 newly installed, 0 to remove and 0 not upgraded.
Need to get 0B/510kB of archives.
After unpacking 1163kB of additional disk space will be used.
Preconfiguring packages ...
tar: ./config: time stamp 2007-09-30 03:37:08 is 9581263.539087013 s in the future
tar: ./templates: time stamp 2007-09-30 03:37:08 is 9581263.537769731 s in the future
tar: ./postinst: time stamp 2007-09-30 03:37:09 is 9581264.53711123 s in the future
tar: ./prerm: time stamp 2007-09-30 03:37:10 is 9581265.536495194 s in the future
tar: ./postrm: time stamp 2007-09-30 03:37:10 is 9581265.535775788 s in the future
tar: ./conffiles: time stamp 2007-09-30 03:37:10 is 9581265.535116728 s in the future
tar: ./md5sums: time stamp 2007-09-30 03:37:10 is 9581265.534501531 s in the future
tar: ./control: time stamp 2007-09-30 03:37:10 is 9581265.533889407 s in the future
tar: .: time stamp 2007-09-30 03:37:10 is 9581265.533276165 s in the future
Selecting previously deselected package sl-modem-daemon.
(Reading database ... 88947 files and directories currently installed.)
Unpacking sl-modem-daemon (from .../sl-modem-daemon_2.9.10+2.9.9d+e-pre2-5ubuntu4_i386.deb) ...
Setting up sl-modem-daemon (2.9.10+2.9.9d+e-pre2-5ubuntu4) ...
Adding system user `Slmodemd' (UID 109) ...
Adding new group `Slmodemd' (GID 120) ...
Adding new user `Slmodemd' (UID 109) with group `Slmodemd' ...
Not creating home directory `/'.
FATAL: Module ungrab_winmodem not found.
FATAL: Module slamr not found.
Starting SmartLink Modem driver for: auto.
Creating /dev/modem symlink, pointing to: /dev/ttySL0.

mahdi@mahdi-desktop:~$

 =======================================================================================

mahdi@mahdi-desktop:~$ wvdialconf
Editing `/etc/wvdial.conf'.

Scanning your serial ports for a modem.

WvModem<*1>: Cannot set information for serial port.
ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
WvModem<*1>: Cannot set information for serial port.
ttyS1<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyS1<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
ttyS1<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
Modem Port Scan<*1>: S2   S3   


Sorry, no modem was detected!  Is it in use by another program?
Did you configure it properly with setserial?

Please read the FAQ at http://open.nit.ca/wiki/?WvDial

If you still have problems, send mail to <wvdial-list@lists.nit.ca>.
mahdi@mahdi-desktop:~$


خروجی دستور             wvdialconf

mahdi@mahdi-desktop:~$ wvdialconf
Editing `/etc/wvdial.conf'.

Scanning your serial ports for a modem.

WvModem<*1>: Cannot set information for serial port.
ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
WvModem<*1>: Cannot set information for serial port.
ttyS1<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyS1<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
ttyS1<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
Modem Port Scan<*1>: S2   S3   


Sorry, no modem was detected!  Is it in use by another program?
Did you configure it properly with setserial?

Please read the FAQ at http://open.nit.ca/wiki/?WvDial

If you still have problems, send mail to <wvdial-list@lists.nit.ca>.
mahdi@mahdi-desktop:~$

[pol100]

خروجی دستور      sudo apt-get install sl-modem-daemon

mahdi@mahdi-desktop:~$ sudo apt-get install sl-modem-daemon
[sudo] password for mahdi:
Reading package lists... Done
Building dependency tree       
Reading state information... Done
The following NEW packages will be installed:
  sl-modem-daemon
0 upgraded, 1 newly installed, 0 to remove and 0 not upgraded.
Need to get 0B/510kB of archives.
After unpacking 1163kB of additional disk space will be used.
Preconfiguring packages ...
tar: ./config: time stamp 2007-09-30 03:37:08 is 9581263.539087013 s in the future
tar: ./templates: time stamp 2007-09-30 03:37:08 is 9581263.537769731 s in the future
tar: ./postinst: time stamp 2007-09-30 03:37:09 is 9581264.53711123 s in the future
tar: ./prerm: time stamp 2007-09-30 03:37:10 is 9581265.536495194 s in the future
tar: ./postrm: time stamp 2007-09-30 03:37:10 is 9581265.535775788 s in the future
tar: ./conffiles: time stamp 2007-09-30 03:37:10 is 9581265.535116728 s in the future
tar: ./md5sums: time stamp 2007-09-30 03:37:10 is 9581265.534501531 s in the future
tar: ./control: time stamp 2007-09-30 03:37:10 is 9581265.533889407 s in the future
tar: .: time stamp 2007-09-30 03:37:10 is 9581265.533276165 s in the future
Selecting previously deselected package sl-modem-daemon.
(Reading database ... 88947 files and directories currently installed.)
Unpacking sl-modem-daemon (from .../sl-modem-daemon_2.9.10+2.9.9d+e-pre2-5ubuntu4_i386.deb) ...
Setting up sl-modem-daemon (2.9.10+2.9.9d+e-pre2-5ubuntu4) ...
Adding system user `Slmodemd' (UID 109) ...
Adding new group `Slmodemd' (GID 120) ...
Adding new user `Slmodemd' (UID 109) with group `Slmodemd' ...
Not creating home directory `/'.
FATAL: Module ungrab_winmodem not found.
FATAL: Module slamr not found.
Starting SmartLink Modem driver for: auto.
Creating /dev/modem symlink, pointing to: /dev/ttySL0.



ضمنا مودم من   Creative Modem Blaster V.90 PCI

[سید مهدی]

پس به اینجا مراجعه کنید و فایل modemData.txt رو برامون بزارین.

[pol100]

پس به اینجا مراجعه کنید و فایل modemData.txt رو برامون بزارین.

Only plain text email is forwarded by the  Discuss@Linmodems.org List Server,
 as HTML can contain viruses. Use as the email Subject Line:
           YourName, YourCountry  kernel 2.6.22-14-generic
 With this Subject Line cogent experts will be alerted, and useful case names left in the Archive.
 YourCountry will enable Country specific guidance. Linux experts in YourCountry
 can be found through: http://www.linux.org/groups/index.html.
They will know your Country's modem code, which may be essential for dialup service.
Responses from Discuss@Linmodems.org are sometimes blocked by an Internet Provider mail filters.
 So in a day, also check the Archived responses at http://www.linmodems.org
--------------------------  System information ----------------------------
CPU=i686, 
Linux version 2.6.22-14-generic (buildd@palmer) (gcc version 4.1.3 20070929 (prerelease) (Ubuntu 4.1.2-16ubuntu2)) #1 SMP Sun Oct 14 23:05:12 GMT 2007
 scanModem update of:  2008_05_30

 There are no blacklisted modem drivers in /etc/modprobe*  files
USB modems not recognized

For candidate card in slot 00:0c.0, firmware information and bootup diagnostics are:
 PCI slot   PCI ID      SubsystemID   Name
 ----------   ---------   ---------   --------------
 00:0c.0   125d:2898   148d:1030   Communication controller: ESS Technology ES2898 Modem

 Modem interrupt assignment and sharing:
 --- Bootup diagnostics for card in PCI slot 00:0c.0 ----

=== Finished firmware and bootup diagnostics, next deducing cogent software. ===

Predictive diagnostics for card in bus 00:0c.0:
   Modem chipset  detected on
CLASS="Class 0780: 125d:2898"
NAME="Communication controller: ESS Technology ES2898 Modem "
SUBSYS=148d:1030
PCIDEV=125d:2898
IRQ=11
IDENT=ESS.com

 For candidate modem in:  00:0c.0
   Class 0780: 125d:2898 Communication controller: ESS Technology ES2898 Modem
      Primary device ID:  125d:2898
 Support type needed or chipset:   ESS.com
 

----------------end Softmodem section --------------
 ESS chipset 125d:2898 modems are supported. Read DOCs/ESScom.txt

 Completed candidate modem analyses.

 The base of the UDEV device file system is: /dev/.udev

 Versions adequately match for the compiler installed: 4.1.3
             and the compiler used in kernel assembly: 4.1.3


 
 Minimal compiling resources appear complete:
   make utility - /usr/bin/make
   Compiler version 4.1
   linuc_headers base folder /lib/modules/2.6.22-14-generic/build

 However some compilations and executable functions may need additional files,
 in the FileNames.h (so called kernel "h"eaders) collection installed in  /usr/include/ .
 For martian_modem, additional required packages are libc6-dev (and for Debian/Ubuntu,
 linux-libc-dev). The also required headers of package libc6 are commonly installed by default.
 Compiling hsfmodem drivers does require linux-libc-dev and libc6-dev packages, for kernels 2.6.24 and later versions.
 In not included on your install CD, search for them at http://packages.ubuntu.com
 or comparable Repository for other Linux distros.
 When compiling ALSA drivers, the utility "patch" will also be needed.




If a driver compilation fails, with message including some lack of some FileName.h (stdio.h for example), then
Some additional kernel-header files need installation to /usr/include. The minimal additional packages are libc6-dev
and any of its dependents, under Ubuntu linux-libc-dev

If an alternate ethernet connection is available,
$  apt-get update
$  apt-get -s install linux-kernel-devel
will install needed packages.
For Debian/Ubuntu related distributions, run the following command to display the needed package list:

Otherwise packages have to be found through http://packages.ubuntu.com
Once downloaded and transferred into a Linux partition,
they can be installed alltogether with:
$ sudo dpkg -i *.deb


Checking pppd properties:
   -rwsr-xr-- 1 root dip 269256 2007-10-04 23:27 /usr/sbin/pppd

In case of an "error 17" "serial loopback" problem, see:
    http://linmodems.technion.ac.il/linmodems/archive-sixth/msg02637.html

To enable dialout without Root permission do:
   $ su - root  (not for Ubuntu)
        sudo chmod a+x /usr/sbin/pppd
or under Ubuntu related Linuxes
   sudo chmod a+x /usr/sbin/pppd

Checking settings of:   /etc/ppp/options
asyncmap 0
noauth
crtscts
lock
hide-password
modem
proxyarp
lcp-echo-interval 30
lcp-echo-failure 4
noipx

In case of a message like:
   Warning: Could not modify /etc/ppp/pap-secrets: Permission denied
see http://linmodems.technion.ac.il/bigarch/archive-sixth/msg04656.html


 Don't worry about the following, it is for experts should trouble shooting be necessary.
==========================================================

 Checking for modem support lines:
 --------------------------------------
     /device/modem symbolic link:   
slmodemd created symbolic link /dev/ttySL0: 
     Within /etc/udev/ files:

     Within /etc/modprobe.conf files:
/etc/modprobe.d/alsa-base:options snd-atiixp-modem index=-2
/etc/modprobe.d/alsa-base:options snd-via82xx-modem index=-2
/etc/modprobe.d/blacklist-modem:# Uncomment these entries in order to blacklist unwanted modem drivers
/etc/modprobe.d/blacklist-modem:# blacklist snd-atiixp-modem
/etc/modprobe.d/blacklist-modem:# blacklist snd-via82xx-modem
     Within any ancient /etc/devfs files:

     Within ancient kernel 2.4.n /etc/module.conf files:

--------- end modem support lines --------

[iqson716]

مودم شما از نوع  ESS Technology ES2898 Modem  هستش
درایورتون رو از اینجا دانلود کنید
فایل دریافتی رو از حالت فشرده خارج کنید و طبق فایل README داخل اون عمل کنید

[سید مهدی]

شاید این پست کمکتون بکنه

[pol100]

شاید این پست کمکتون بکنه

از صمیم قلب متشکرم
مودمم نصب شد

[pol100]

شاید این پست کمکتون بکنه

از صمیم قلب متشکرم
مودمم نصب شد

حالا که مودم نصب شده و کانکت میشه
ولی وقتی فایر فاکس باز می کنم و  سایتی انتخاب کنم سایت  باز نمی شه

[pol100]

شاید این پست کمکتون بکنه

حالا مودمم نصب شده  ولی دو مشکلی هست

1 - هنوز لینوکس لود نشده کانکت مشه .
2-با اینکه کانکت سایت باز نمی کنه

ضمنا من برای ساختن کانکت از ابزار گرافیکی مدیریتی Network  استفاده کردم  ابزار  خط فرمانی  pppconfig  استفاده کردم جواب نداد

باز هم متشکرم

[سید مهدی]

۱- دستور زیر رو وارد کنید:

کد: [انتخاب]

sudo network-adminو از اونجا برید Point to Point connection رو بدون تیک کنید.

۲- دستور زیر رو وارد کنید (بعد از اینکه کانکت شد)

کد: [انتخاب]

echo "nameserver 4.2.2.4" | sudo tee /etc/resolv.conf

پ‌ن: بهتره از یک برنامه دیگه برای کانکت شدن استفاده کنید. مثل Gnome ppp