انجمن‌های فارسی اوبونتو

لطفاً به انجمن‌ها وارد شده و یا جهت ورود ثبت‌نام نمائید

لطفاً جهت ورود نام کاربری و رمز عبورتان را وارد نمائید


ارائه ۲۵٫۰۴ اوبونتو منتشر شد 🎉

نویسنده موضوع: گیر کردن تو آخرین قدم...  (دفعات بازدید: 7087 بار)

0 کاربر و 1 مهمان درحال مشاهده موضوع.

آفلاین s4lish

  • Newbie
  • *
  • ارسال: 11
گیر کردن تو آخرین قدم...
« : 18 خرداد 1388، 03:02 ب‌ظ »
سلام دوستان..
سرانجام بعد از هزاران مصیبت و بدبختی تونستم مودم رو نصب کنم و به زور یه کانکشن درست کنم.
حالا اینترنت هم وصل می شه ولی هیچ سایتی رو باز نمی کنه.انگار که اصلا اینترنت وصل نیست.
بگم که لپ تابم dell vostro 1510 است و مودمش هم بیرونیه Conexant d400 است.
چراغ مودم روشنه یعنی وصله ولی اینترنتی در کار نیست.
چیکار باید بکنم.
کم مونده کامپیوترو تو سرم بکوبم. ](*,) ](*,) ](*,) ](*,)

آفلاین ناربه

  • ناظر انجمن
  • *
  • ارسال: 2033
  • جنسیت : پسر
پاسخ به: گیر کردن تو آخرین قدم...
« پاسخ #1 : 18 خرداد 1388، 05:15 ب‌ظ »
اگر مودمتون HSF است توی ترمینال بزنید:

sudo hsfconfig
و اگر DGC است:

sudo dgcconfig

آفلاین s4lish

  • Newbie
  • *
  • ارسال: 11
پاسخ به: گیر کردن تو آخرین قدم...
« پاسخ #2 : 18 خرداد 1388، 05:57 ب‌ظ »
انگار دقت نکردید من چی گفتم.
این کارا مال قدیم بود.
حالا همه چی درسته.
اینترنت نصب میشه.
وقتی می خوام با فایرفاکس وصل بشم .اصلا انگار اینترنت وصل نیستم.
از اون لحاظ

آفلاین s4lish

  • Newbie
  • *
  • ارسال: 11
پاسخ به: گیر کردن تو آخرین قدم...
« پاسخ #3 : 19 خرداد 1388، 12:19 ق‌ظ »
ببینید واضح تر می گم.
صدای وز وز مودم رو می شنوم. بعد از چراغهای مودم می فهمم که نصبه ولی بعد از مدتی دوباره دیسکانکت می شم.
همه چی جوره.
چیپ ست مودمم از نوع gdc است و وقتی خواستم hsf رو نصب کنم اخطار می داد و از اونجا فهمیدم که اصلا طرفای hsf نیست.
تازه درایور رو بر اساس کرنل ابونتو دانلود کردم. ولی آخرش نمی دونم چیکاز کنم.

آفلاین Saman.S

  • Sr. Member
  • *
  • ارسال: 322
  • جنسیت : پسر
پاسخ به: گیر کردن تو آخرین قدم...
« پاسخ #4 : 19 خرداد 1388، 08:26 ق‌ظ »
ببینید واضح تر می گم.
صدای وز وز مودم رو می شنوم. بعد از چراغهای مودم می فهمم که نصبه ولی بعد از مدتی دوباره دیسکانکت می شم.
همه چی جوره.
چیپ ست مودمم از نوع gdc است و وقتی خواستم hsf رو نصب کنم اخطار می داد و از اونجا فهمیدم که اصلا طرفای hsf نیست.
تازه درایور رو بر اساس کرنل ابونتو دانلود کردم. ولی آخرش نمی دونم چیکاز کنم.


از چه برنامه ای برای اتصال به اینترنت استفاده می کنید؟
اگه از wvdial استفاده نمی کنید, حتما نصبش کنید و با اون وصل شید.
اگه از wvdial استفاده می کنید, خروجی دستور sudo wvdial رو بذارید.

آفلاین s4lish

  • Newbie
  • *
  • ارسال: 11
پاسخ به: گیر کردن تو آخرین قدم...
« پاسخ #5 : 19 خرداد 1388، 12:14 ب‌ظ »
خیر با wvdial بلد نیستم نصب بشم.
با pppconfig  و بصورت گرافیکی نصب می شم .شاید فکر کردم که درایور رو اشتباه نصب کردم و تو یه پست دیگه فایل scanmodem رو گذاشتم و دوستان
نظر منو در مورد درست نصب کردن درایو تایید کردند..

آفلاین Saman.S

  • Sr. Member
  • *
  • ارسال: 322
  • جنسیت : پسر
پاسخ به: گیر کردن تو آخرین قدم...
« پاسخ #6 : 19 خرداد 1388، 01:19 ب‌ظ »
خیر با wvdial بلد نیستم نصب بشم.

پس حتما کار با wvdial رو از لینک زیر یاد بگیرید.
http://wiki.ubuntu-ir.org/DialupModemHowto/SetUpDialer#head-0bfb6c809d1da16feabe2dfe21eb748f9a230cd0هر جا به مشکل برخوردید, خروجی دستورsudo wvdial رو اینجا بذارید تا دوستان کمکتون کنن.

آفلاین s4lish

  • Newbie
  • *
  • ارسال: 11
پاسخ به: گیر کردن تو آخرین قدم...
« پاسخ #7 : 21 خرداد 1388، 07:10 ب‌ظ »
دست همگی درد نکنه .مشکل ما به کل رفع شد. ;D ;D ;D :)

آفلاین Hamed.montazer

  • Newbie
  • *
  • ارسال: 5
پاسخ به: گیر کردن تو آخرین قدم...
« پاسخ #8 : 30 آذر 1388، 07:44 ب‌ظ »
سلام میشه لطف کنید و درایور راه انداز مودم d400 تون رو برای منهم بزارید چون منم یه ۱۵۱۰ دارم و داریور رو لازم دارم ??? ???

آفلاین SAM1

  • Sr. Member
  • *
  • ارسال: 382
  • جنسیت : پسر
  • LONG LIVE FREEDOM
پاسخ به: گیر کردن تو آخرین قدم...
« پاسخ #9 : 02 دی 1388، 03:50 ب‌ظ »
سلام میشه لطف کنید و درایور راه انداز مودم d400 تون رو برای منهم بزارید چون منم یه ۱۵۱۰ دارم و داریور رو لازم دارم ??? ???
ورژن کرنل را با دستور uname -r ببینید و از صفحه زیر نسخه generic خالی (نه generic_pae و نه 386 !) را دانلود کنید: http://www.linuxant.com/drivers/dgc/downloads-ubuntu-x86.php
رسیده ها چه غریب و نچیده می افتند، به پای هرزه علفهای باغ کال پرست

وطنم

آفلاین haji_1369

  • Newbie
  • *
  • ارسال: 16
پاسخ به: گیر کردن تو آخرین قدم...
« پاسخ #10 : 26 دی 1388، 07:33 ب‌ظ »
سلام
 من اوبونتو ۹.۱۰ هستم و یه سری خروجیها رو میدم لطفا کمک کنن:
مودم دیتا:
Only plain text email is forwarded by the  Discuss@Linmodems.org List Server,
 as HTML can contain viruses. Use as the email Subject Line:
           YourName, YourCountry  kernel 2.6.31-17-generic
 With this Subject Line cogent experts will be alerted, and useful case names left in the Archive.
 YourCountry will enable Country specific guidance. Linux experts in YourCountry
 can be found through: http://www.linux.org/groups/index.html.
They will know your Country's modem code, which may be essential for dialup service.
Responses from Discuss@Linmodems.org are sometimes blocked by an Internet Provider mail filters.
 So in a day, also check the Archived responses at http://www.linmodems.org
--------------------------  System information ----------------------------
CPU=i686,  
Linux version 2.6.31-17-generic (buildd@palmer) (gcc version 4.4.1 (Ubuntu 4.4.1-4ubuntu8) ) #54-Ubuntu SMP Thu Dec 10 16:20:31 UTC 2009
 scanModem update of:  2010_01_13
The modem symbolic link is /dev/modem -> ttySL0
The slmodemd set symbolic link is /dev/ttySL0 -> /dev/pts/0
The dialer utility package WVDIAL does not appear to be installed on your System.
For Ubuntu users, there are at the bottom of http://linmodems.technion.ac.il/packages/
packages with the files necessary to install wvdial, with names like:
     wvdial_jaunty_amd64.zip   for x86_64, 64 bit bus systems.
     wvdial_jaunty_i386.zip    for 32 bit systems.
     wvdial_karmic_i386.zip    for 32 bit systems.
These are about 1 MB in size.  After downloaded and copied into your Linux partition:
$ unzip wv*.zip
Within the new folder:
$ sudo dpkg -i *.deb
will  complete the wvdial installation
Please read Modem/DOCs/wvdial.txt for usage information.

The dkms driver upgrade utilities are installed,

 There are no blacklisted modem drivers in /etc/modprobe*  files

 Potentially useful modem drivers now loaded are:
       snd_hda_intel          

Attached USB devices are:
 ID 0483:2016 SGS Thomson Microelectronics Fingerprint Reader
 ID 046d:c521 Logitech, Inc. MX620 Laser Cordless Mouse
If a cellphone is not detected, see http://ubuntuforums.org/archive/index.php/t-878554.html
A sample report is:  http://linmodems.technion.ac.il/bigarch/archive-nineth/msg00578.html

If a USB modem or cellphone is attached and was not detected, please
provide available information in your request to discuss@linmodems.org

For candidate card in slot 00:1b.0, firmware information and bootup diagnostics are:
 PCI slot PCI ID SubsystemID Name
 ---------- --------- --------- --------------
 00:1b.0 8086:27d8 1179:0001 Audio device: Intel Corporation 82801G

 Modem interrupt assignment and sharing:
 22:       9574          0   IO-APIC-fasteoi   HDA Intel
 --- Bootup diagnostics for card in PCI slot 00:1b.0 ----
[    0.180674] pci 0000:00:1b.0: reg 10 64bit mmio: [0x000000-0x003fff]
[    0.180821] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[    0.180826] pci 0000:00:1b.0: PME# disabled
[   24.668304] HDA Intel 0000:00:1b.0: power state changed by ACPI to D0
[   24.668313] HDA Intel 0000:00:1b.0: enabling device (0000 -> 0002)
[   24.668330] HDA Intel 0000:00:1b.0: PCI INT A -> GSI 22 (level, low) -> IRQ 22
[   24.668370] HDA Intel 0000:00:1b.0: setting latency timer to 64
[   24.945202] input: HDA Intel Line In at Sep Rear Jack as /devices/pci0000:00/0000:00:1b.0/sound/card0/input10

 The PCI slot 00:1b.0 of the modem card may be disabled early in
 a bootup process,  but then enabled later. If modem drivers load
 but the  modem is not responsive, read DOCs/Bootup.txt about possible fixes.
 Send dmesg.txt along with ModemData.txt to discuss@linmodems.org
 if help is needed.
 


===== Advanced Linux Sound Architecture (ALSA) diagnostics =====
The ALSA packages provide audio support and also drivers for some modems.
ALSA diagnostics are written during bootup to /proc/asound/ folders.

The ALSA verion is 1.0.20
The modem cards detected by "aplay -l"  are:
card 0: Intel [HDA Intel], device 6: Si3054 Modem [Si3054 Modem]

The /proc/asound/pcm file reports:
-----------------------
00-00: STAC92xx Analog : STAC92xx Analog : playback 1 : capture 1
00-06: Si3054 Modem : Si3054 Modem : playback 1 : capture 1

about /proc/asound/cards:
------------------------
 0 [Intel          ]: HDA-Intel - HDA Intel
                      HDA Intel at 0x8a000000 irq 22

 PCI slot 00:1b.0 has a High Definition Audio Card
 The drivers are in the kernel modules tree at:
 /lib/modules/2.6.31-17-generic/kernel/sound/pci/hda/snd-hda-intel.ko
/lib/modules/2.6.31-16-generic/kernel/sound/pci/hda/snd-hda-intel.ko
/lib/modules/2.6.31-14-generic/kernel/sound/pci/hda/snd-hda-intel.ko
 The modem codec file for the HDA card is: /proc/asound/card0/codec#1
--------------------------------------------------------
Codec: LSI Si3054
Address: 1
Function Id: 0x2
Vendor Id: 0x11c13026
Subsystem Id: 0x11790001
Revision Id: 0x100700
Modem Function Group: 0x1

 The audio card hosts a softmodem chip:  0x11c13026

The softmodem chip 0x11c13026 is in principle supported by the COMM support of slmodemd
and the joint snd-hda-intel audio+modem driver, begun with ALSA version 1.0.13.  
For HDA cards with ALC883 chips, an upgrade to ALSA verions 1.0.15 way be necessary. Instructions for Upgrading snd-hda-intel and its dependent driver set are at:
http://linmodems.technion.ac.il/bigarch/archive-eighth/msg00838.html

If not a Conexant modem, the driver snd-hda-intel with its dependent drivers:
snd_hda_intel          26920  5
snd_hda_codec          75708  3 snd_hda_codec_si3054,snd_hda_codec_idt,snd_hda_intel
snd_pcm                75296  6 snd_hda_codec_si3054,snd_hda_intel,snd_hda_codec,snd_pcm_oss
snd                    59204  21 snd_hda_codec_si3054,snd_hda_codec_idt,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device
snd_page_alloc          9156  2 snd_hda_intel,snd_pcm
----------
provide audio + modem support with the modem chip residing on the subsystem.
Any particular card can host any one of several soft modem chips.

=== Finished firmware and bootup diagnostics, next deducing cogent software. ===

Predictive  diagnostics for card in bus 00:1b.0:
Modem chipset  detected on
NAME="Audio device: Intel Corporation 82801G "
CLASS=0403
PCIDEV=8086:27d8
SUBSYS=1179:0001
IRQ=22
HDA=8086:27d8
SOFT=8086:27d8.HDA
HDAchipVendorID=11c1
CHIP=0x11c13026
IDENT=slmodemd
SLMODEMD_DEVICE=hw:0,6
Driver=snd-hda-intel

 For candidate modem in:  00:1b.0
   0403 Audio device: Intel Corporation 82801G
      Primary device ID:  8086:27d8
    Subsystem PCI_id  1179:0001
    Softmodem codec or chipset from diagnostics: 0x11c13026
                               from    Archives:
                        The HDA card softmodem chip is 0x11c13026
      

Support type needed or chipset: slmodemd supporting the snd-hda-intel audio+modem driver

 An ALSA (Advanced Linux Sound Architecture) modem driver:  snd-hda-intel
 provides Low Level support enabling contact with the modem hardware.
 For all BUT Conexant chip soft modems (using hsfmodem software)
 complementary High Level support is through a Smartlink utility:  slmodemd

 Download from http://linmodems.technion.ac.il/packages/smartlink/
 the package SLMODEMD.gcc4.4.tar.gz having a compiled slmodemd. Unpack under Linux with:
  $ tar zxf SLMODEMD.gcc4.4.tar.gz
 and read instructions therein. But briefly, the modem is setup with command:
  sudo slmodemd -c YOUR_COUNTRY --alsa hw:0,6
 reporting dynamic creation of ports:
/dev/ttySL0 --> /dev/pts/N   , with N some number
 Read DOCs/Smartlink.txt and Modem/DOCs/YourSystem.txt for follow through guidance.
 

Writing DOCs/Intel.txt
Writing DOCs/Smartlink.txt
============ end Smartlink section =====================

The AgereSystems/LSI agrsm code supports compiling of a agrmodem + agrserial driver pair.
There are a few different chipsets which use this driver pair, but they use different code resources:
Chipsets KV* PackageNames (most current as of November 2009)
----------------------------------------------------------------------------------------------
11c1:048c and 11c1:048f         2.6.29 agrsm048pci-2.1.60_20100108_i386.deb or agrsm048pci-2.1.60_20100108.tar.gz
11c1:0620                       2.6.31  agrsm06pci-2.1.80_20100106_i386.deb or agrsm06pci-2.1.80~20100106.tar.gz !!
11c11040 (on HDA audio cards)   2.6.31  agrsm-11c11040-2.1.80~20091225.tar.bz2  !!
   All available at: http://linmodems.technion.ac.il/packages/ltmodem/11c11040/   , whereat additionally
automation & testing                    agrsm-tools_0.0.1_all.deb or agrsm-tools-0.0.1-2.noarch.rpm
General background                      agrsm_howto.txt
for rpm variants of dkms-agrsm , see  http://linux.zsolttech.com/linmodem/agrsm/
------------------------------------------------------------------------------------------------
* KV == latest kernel release with a reported success
!! Latest update with major credit to  Nikolay Zhuravlev
   But see conflict issue: http://linmodems.technion.ac.il/bigarch/archive-nineth/msg02753.html
Report from  Bjorn Wielens:
Please note- trying to load the modules on a OpenSuSE 11.2 system gives
 an error about the module_version symbol. Using:
# modprobe --force agrmodem
# modprobe --force agrserial
is necessary to load the drivers, and does not appear to cause ill effects.


All of the above packages are dkms competent.  This means that if your Linux distros dkms package
is previously installed, if provides for future updates matching forthcoming kernels.

-------------- end Agere Systems section -------------------

 Completed candidate modem analyses.

 The base of the UDEV device file system is: /dev/.udev

 Versions adequately match for the compiler installed: 4.4.1
             and the compiler used in kernel assembly: 4.4.1


 
 Minimal compiling resources appear complete:
   make utility - /usr/bin/make
   Compiler version 4.4
   linuc_headers base folder /lib/modules/2.6.31-17-generic/build

 However some compilations and executable functions may need additional files,
 in the FileNames.h (so called kernel "h"eaders) collection installed in  /usr/include/ .
 For martian_modem, additional required packages are needed. The also required headers of package libc6 are commonly installed by default.
 Compiling hsfmodem drivers does require linux-libc-dev and libc6-dev packages, for kernels 2.6.24 and later versions.
 In not included on your install CD, search for them at http://packages.ubuntu.com
 or comparable Repository for other Linux distros.
 When compiling ALSA drivers, the utility "patch" will also be needed.




If a driver compilation fails, with message including some lack of some FileName.h (stdio.h for example), then
Some additional kernel-header files need installation to /usr/include. The minimal additional packages are libc6-dev
and any of its dependents, under Ubuntu linux-libc-dev

If an alternate ethernet connection is available,
$  apt-get update
$  apt-get -s install linux-kernel-devel
will install needed packages.
For Debian/Ubuntu related distributions, run the following command to display the needed package list:

Otherwise packages have to be found through http://packages.ubuntu.com
Once downloaded and transferred into a Linux partition,
they can be installed alltogether with:
$ sudo dpkg -i *.deb

Checking settings of: /etc/ppp/options
asyncmap 0
noauth
crtscts
lock
hide-password
modem
proxyarp
lcp-echo-interval 30
lcp-echo-failure 4
noipx

In case of a message like:
   Warning: Could not modify /etc/ppp/pap-secrets: Permission denied
see http://linmodems.technion.ac.il/bigarch/archive-sixth/msg04656.html

For guidance on FAX usage, get from http://linmodems.technion.ac.il/packages/  get faxing.tar.gz
It has samples for a modem using port /dev/ttySL0, which must be changed to match your modem's port.

Read Modem/DOCs/YourSystem.txt concerning other COMM channels: eth0 wlan0 wmaster0
Which can interfere with Browser naviagation.

 Don't worry about the following, it is for experts should trouble shooting be necessary.
==========================================================

 Checking for modem support lines:
 --------------------------------------
     /device/modem symbolic link:   lrwxrwxrwx 1 root root 6 2010-01-15 16:07 /dev/modem -> ttySL0
slmodemd created symbolic link /dev/ttySL0:  lrwxrwxrwx 1 root root 10 2010-01-15 16:07 /dev/ttySL0 -> /dev/pts/0
     Within /etc/udev/ files:

     Within /etc/modprobe.conf files:
/etc/modprobe.d/alsa-base.conf:options snd-atiixp-modem index=-2
/etc/modprobe.d/alsa-base.conf:options snd-via82xx-modem index=-2
/etc/modprobe.d/blacklist-modem.conf:# Uncomment these entries in order to blacklist unwanted modem drivers
/etc/modprobe.d/blacklist-modem.conf:# blacklist snd-atiixp-modem
/etc/modprobe.d/blacklist-modem.conf:# blacklist snd-via82xx-modem
     Within any ancient /etc/devfs files:

     Within ancient kernel 2.4.n /etc/module.conf files:

--------- end modem support lines --------
و
ali@Can3r:~$ uname -r
2.6.31-17-generic
وali@Can3r:~$ lspci

00:00.0 Host bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub (rev 03)

00:01.0 PCI bridge: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express PCI Express Root Port (rev 03)

00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02)

00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 02)

00:1c.1 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 2 (rev 02)

00:1c.2 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 3 (rev 02)

00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 02)

00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 02)

00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 02)

00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 02)

00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 02)

00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev e2)

00:1f.0 ISA bridge: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge (rev 02)

00:1f.2 IDE interface: Intel Corporation 82801GBM/GHM (ICH7 Family) SATA IDE Controller (rev 02)

01:00.0 VGA compatible controller: nVidia Corporation G72M [Quadro NVS 110M] (rev a1)

02:00.0 Ethernet controller: Intel Corporation 82573L Gigabit Ethernet Controller

05:00.0 Network controller: Intel Corporation PRO/Wireless 3945ABG [Golan] Network Connection (rev 02)

06:0b.0 CardBus bridge: Texas Instruments PCIxx12 Cardbus Controller

06:0b.1 FireWire (IEEE 1394): Texas Instruments PCIxx12 OHCI Compliant IEEE 1394 Host Controller

06:0b.3 SD Host controller: Texas Instruments PCIxx12 SDA Standard Compliant SD Host Controller
حالا اگه میشه بگید نوع مودمم چیه.

آفلاین SAM1

  • Sr. Member
  • *
  • ارسال: 382
  • جنسیت : پسر
  • LONG LIVE FREEDOM
پاسخ به: گیر کردن تو آخرین قدم...
« پاسخ #11 : 26 دی 1388، 08:54 ب‌ظ »
حالا اگه میشه بگید نوع مودمم چیه.
لپ تاپ شما احتمالا HP Pavilion و مودمتون هم موتورولا Si3054 هست. اینجا نوشته انگار باید بسته slmodem را از مخازن نصب کنید و یه پکیج را هم دانلود کنید و اجراش کنید. توضیحات کامل را تو همون لینک بخونید.
رسیده ها چه غریب و نچیده می افتند، به پای هرزه علفهای باغ کال پرست

وطنم

آفلاین haji_1369

  • Newbie
  • *
  • ارسال: 16
پاسخ به: گیر کردن تو آخرین قدم...
« پاسخ #12 : 27 دی 1388، 03:42 ق‌ظ »
سلام
اینو نمیتونم ذخیره کنم:Then you will want to edit /etc/default/sl-modem-daemon and set the following

Set the SLMODEMD_DEVICE= to your hardware (in my case SLMODEMD_DEVICE=hw:0,6)

Set the SLMODEMD_COUNTRY= to the correct country (slmodemd --countrylist will pop out a list of supported countries)

you’ll also need to edit the OPTS= line so it looks like OPTS=”-g dialout” or you’ll have the uucp group/permissions problem mentioned above.

now save the file

آفلاین SAM1

  • Sr. Member
  • *
  • ارسال: 382
  • جنسیت : پسر
  • LONG LIVE FREEDOM
پاسخ به: گیر کردن تو آخرین قدم...
« پاسخ #13 : 27 دی 1388، 01:30 ب‌ظ »
سلام
اینو نمیتونم ذخیره کنم:Then you will want to edit /etc/default/sl-modem-daemon and set the following

Set the SLMODEMD_DEVICE= to your hardware (in my case SLMODEMD_DEVICE=hw:0,6)

Set the SLMODEMD_COUNTRY= to the correct country (slmodemd --countrylist will pop out a list of supported countries)

you’ll also need to edit the OPTS= line so it looks like OPTS=”-g dialout” or you’ll have the uucp group/permissions problem mentioned above.

now save the file
یعنی چی نمی تونی ذخیره کنی؟ یعنی فایله را پیدا نمی کنی؟ با دستور زیر پیداش کن:

locate sl-modem-daemon /
رسیده ها چه غریب و نچیده می افتند، به پای هرزه علفهای باغ کال پرست

وطنم

آفلاین haji_1369

  • Newbie
  • *
  • ارسال: 16
پاسخ به: گیر کردن تو آخرین قدم...
« پاسخ #14 : 27 دی 1388، 11:06 ب‌ظ »
نه منظورم اینه که اجازه نمیده تغییرات رو ذخیره کنم.
دستور save غیر فعاله. ???