راهنمای جامع نصب مودم و برقراری اتصال به اینترنت

[moshen212]

سلام

من تازه اوبونتو 8.10 رو نصب کردم و احتیاج شدید دارم که به اینترنت وصل شم. اول که مودم رو نمی شناخت که با هزار بدبختی رفع شد. کانکشن دایال آپ رو هم ساختم که با pon جواب نمی داد که هز wvdial استفاده کردم. کانکت شدم ولی صفحه  رو باز نمیکنه. تو منوی adminstration هم گزینه ای به نام network ندارم. network tool دارم که اصلا گزینه dial up نداره. من باید چی کار کنم؟
در ضمن وقتی از ubuntu خارج میشم و دوباره بر میگردم باز مودمم رو نمیشناسه و باید مراحل نصب رو از اول طی کنم.
اگر ممکه راهنمایی کنید.

در مورد ریست شدن درایور نمیدونم ولی اگر که با Wvdial وصل میشه ولی send/receive ندارید مطمئنا نباید با  pppconfig این مشکل رو داشته باشید . دوباره pppconfig رو امتحان کنید .

[g.mehr]

من اون روش رو اول از همه امتحان کردم اما error می داد. تو همین انجمن گشتم بچه ها گفته بودن اولش sudo باید گذاشت، گذاشتم اما باز هم جواب نداد.

[Saman.S]

سلام
من تازه اوبونتو 8.10 رو نصب کردم و احتیاج شدید دارم که به اینترنت وصل شم. اول که مودم رو نمی شناخت که با هزار بدبختی رفع شد. کانکشن دایال آپ رو هم ساختم که با pon جواب نمی داد که هز wvdial استفاده کردم. کانکت شدم ولی صفحه  رو باز نمیکنه. تو منوی adminstration هم گزینه ای به نام network ندارم. network tool دارم که اصلا گزینه dial up نداره. من باید چی کار کنم؟
در ضمن وقتی از ubuntu خارج میشم و دوباره بر میگردم باز مودمم رو نمیشناسه و باید مراحل نصب رو از اول طی کنم.
اگر ممکه راهنمایی کنید.

مودمتون چیه؟
خروجی این دستورها رو بذارید:

کد: [انتخاب]

sudo wvdial
wvdialconf
lspci
lsusb
ping www.google.com

[g.mehr]

مودم من:
Smart Link Ltd. SmartPCI2800 V.92 PCI Soft DFT
من مودم رو نصب کردم اما هربار که از لینوکس خارج میشم و برمی گردم دوباره مودم رو نمی شناسه.

کد: [انتخاب]

wvdialconf
Editing `/etc/wvdial.conf'.

Scanning your serial ports for a modem.

WvModem<*1>: Cannot set information for serial port.
ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
Modem Port Scan<*1>: S1   S2   S3   
ttySL0<Info>: Permission denied
Modem Port Scan<*1>: SL0 


Sorry, no modem was detected!  Is it in use by another program?
Did you configure it properly with setserial?

Please read the FAQ at http://open.nit.ca/wiki/?WvDial

If you still have problems, send mail to <wvdial-list@lists.nit.ca>.برای همین با دستورات زیر دوباره نصبش کردم:

کد: [انتخاب]


tar zxvf slamr*.tar.gz
./._slamr-2.6.27-7-generic
slamr-2.6.27-7-generic/
slamr-2.6.27-7-generic/.#setup
slamr-2.6.27-7-generic/._1st_Read.txt
slamr-2.6.27-7-generic/1st_Read.txt
slamr-2.6.27-7-generic/._CountryList.txt
slamr-2.6.27-7-generic/CountryList.txt
slamr-2.6.27-7-generic/._setup
slamr-2.6.27-7-generic/setup
slamr-2.6.27-7-generic/._sl-modem-daemon_2.9.10+2.9.9d+e-pre2-5ubuntu4_i386.deb
slamr-2.6.27-7-generic/sl-modem-daemon_2.9.10+2.9.9d+e-pre2-5ubuntu4_i386.deb
slamr-2.6.27-7-generic/._slamr.ko
slamr-2.6.27-7-generic/slamr.ko
slamr-2.6.27-7-generic/._slmodemd
slamr-2.6.27-7-generic/slmodemd
slamr-2.6.27-7-generic/._Smartlink.txt
slamr-2.6.27-7-generic/Smartlink.txt
slamr-2.6.27-7-generic/._ungrab-winmodem.ko
slamr-2.6.27-7-generic/ungrab-winmodem.ko
slamr-2.6.27-7-generic/._unloading
slamr-2.6.27-7-generic/unloading
slamr-2.6.27-7-generic/._wvdial.txt
slamr-2.6.27-7-generic/wvdial.txt


 :cd slamr*

slamr-2.6.27-7-generic$ sudo ./setup
 
installing drivers for kernel version 2.6.27-7-generic
driver=slamr

Installing the Debian packages supporting autoloading
(Reading database ... 99833 files and directories currently installed.)
Preparing to replace sl-modem-daemon 2.9.10+2.9.9d+e-pre2-5ubuntu4 (using sl-modem-daemon_2.9.10+2.9.9d+e-pre2-5ubuntu4_i386.deb) ...
Shutting down SmartLink Modem driver normally.
Unloading modem driver from kernel ... slamr.
Unpacking replacement sl-modem-daemon ...
Setting up sl-modem-daemon (2.9.10+2.9.9d+e-pre2-5ubuntu4) ...
The system user `Slmodemd' already exists. Exiting.
update-rc.d: warning: /etc/init.d/sl-modem-daemon missing LSB style header
Starting SmartLink Modem driver for: slamr0.
Creating /dev/modem symlink, pointing to: /dev/ttySL0.


Copying over newer files
Making folder /lib/modules/2.6.27-7-generic/extra
Copying drivers to /lib/modules/2.6.27-7-generic/extra
Checking driver install
slamr.ko  ungrab-winmodem.ko
Copying newer slmodemd to /usr/sbin/
Checking slmodemd version. Should be 2.9.11
SmartLink Soft Modem: version 2.9.11 Nov 27 2008 14:36:23
Finished installs.
Informing the System

Starting function tests, loading drivers:
Running diagnostic:

[   10.721742] slamr: module license 'Smart Link Ltd.' taints kernel.
[   10.759800] slamr: SmartLink AMRMO modem.
[   10.759864] slamr: probe 2000:2800 SL2800 card...
[   10.759877] slamr 0000:04:00.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[   10.760534] slamr: slamr0 is SL2800 card.
[  244.028307] slamr 0000:04:00.0: PCI INT A disabled
[  245.353119] slamr: SmartLink AMRMO modem.
[  245.354240] slamr: probe 2000:2800 SL2800 card...
[  245.354262] slamr 0000:04:00.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[  245.358208] slamr: slamr0 is SL2800 card.
echo  "ports should be created by:"
echo slmodemd -c USA /dev/"slamr"0
echo "slmodemd was compiled with gcc-4.2, because of a compiled failure under the gcc-4.3 used to compile the drivers."
/usr/sbin/slmodemd -c USA /dev/"slamr"0

echo "Checking for success"
if test -L /dev/ttySL0 ; then
  echo Running wvdialconf
  wvdialconf  /etc/wvdial.conf
  if [ -f /etc/wvdial.conf ] ; then
    echo Modem detection successful
    sleep 2
    echo "Carrier check = no" >>  /etc/wvdial.conf
    echo "Read wdial.txt"
    echo "Then edit /etc/wvdial.conf  with:"
    echo "sudo gedit /etc/wvdial.conf"
    echo "at the lines beginning with ; and deleting the ; < >  "
    echo "Then dialout with:"
    echo " sudo wvdial"
    echo "Running setup again is NOT necessary. Only for dialout the:"
    echo " sudo wvdial"
  else
    echo "wvdialconf failed"
  fi
else
  echo "Port creation with slmodemd failed."
fi
echo "Read the Slamr.txt record, other *.txt files and the sample wvdial.conf ."
echo
# ENDبعد برای امتحان دوباره دستور زیر رو اجرا کردم:

کد: [انتخاب]

wvdialconf

Editing `/etc/wvdial.conf'.

Scanning your serial ports for a modem.

WvModem<*1>: Cannot set information for serial port.
ttyS0<*1>: ATQ0 V1 E1 -- failed with 2400 baud, next try: 9600 baud
ttyS0<*1>: ATQ0 V1 E1 -- failed with 9600 baud, next try: 115200 baud
ttyS0<*1>: ATQ0 V1 E1 -- and failed too at 115200, giving up.
Modem Port Scan<*1>: S1   S2   S3   
WvModem<*1>: Cannot get information for serial port.
ttySL0<*1>: ATQ0 V1 E1 -- OK
ttySL0<*1>: ATQ0 V1 E1 Z -- OK
ttySL0<*1>: ATQ0 V1 E1 S0=0 -- OK
ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK
ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK
ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK
ttySL0<*1>: Modem Identifier: ATI -- SmartLink Soft Modem
ttySL0<*1>: Speed 4800: AT -- OK
ttySL0<*1>: Speed 9600: AT -- OK
ttySL0<*1>: Speed 19200: AT -- OK
ttySL0<*1>: Speed 38400: AT -- OK
ttySL0<*1>: Speed 57600: AT -- OK
ttySL0<*1>: Speed 115200: AT -- OK
ttySL0<*1>: Speed 230400: AT -- OK
ttySL0<*1>: Speed 460800: AT -- OK
ttySL0<*1>: Max speed is 460800; that should be safe.
ttySL0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK

Found a modem on /dev/ttySL0.
Modem configuration written to /etc/wvdial.conf.
/etc/wvdial.conf<Warn>: Can't write '/etc/wvdial.conf.tmp5820': Permission denied
/etc/wvdial.conf<Warn>: Can't write '/etc/wvdial.conf' ('/etc/wvdial.conf'): Bad file descriptor
ttySL0<Info>: Speed 460800; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0"
بعد دستور اتصال به اینترنت:

کد: [انتخاب]

wvdial
--> WvDial: Internet dialer version 1.60
--> Cannot get information for serial port.
--> Initializing modem.
--> Sending: ATZ
ATZ
OK
--> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
OK
--> Modem initialized.
--> Sending: ATDT9711805
--> Waiting for carrier.
ATDT9711805
CONNECT 48000
--> Carrier detected.  Waiting for prompt.
--> Connected, but carrier signal lost!  Retrying...
--> Sending: ATDT9711805
--> Waiting for carrier.
Welcome to 3Com Total Control HiPer ARC (TM)
Networks That Go The Distance (TM)
login:
ATDT9711805
Password:

فکر میکنم کانکت میشم چون اول صدای قیژ قیژ مودم و بعد هم صدای وصل شدن میاد. من شماره ای که باهاش وصل می شدم هم رو گرفتم و اشغال بود.
بعد باقی دستوراتی که گفته بودید:

کد: [انتخاب]

lspci
00:00.0 Host bridge: Intel Corporation 82945G/GZ/P/PL Memory Controller Hub (rev 02)
00:01.0 PCI bridge: Intel Corporation 82945G/GZ/P/PL PCI Express Root Port (rev 02)
00:1b.0 Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 01)
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 01)
00:1c.3 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 4 (rev 01)
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #1 (rev 01)
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #2 (rev 01)
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #3 (rev 01)
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI Controller #4 (rev 01)
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1)
00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01)
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01)
00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) SATA IDE Controller (rev 01)
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01)
01:00.0 VGA compatible controller: nVidia Corporation G71 [GeForce 7300 GS] (rev a1)
03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 01)
04:00.0 Modem: Smart Link Ltd. SmartPCI2800 V.92 PCI Soft DFT (rev 02)

 lsusb
Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub


ping www.google.com
ping: unknown host www.google.com


البته نمی دونم چه جوری باید دیس کانکت شم اما وقتی log outکردم صدای تق قطع شدن مودم رو شنیدم.
در ضمن من اوبونتو رو کنار ویندوز دارم. یعنی سوایی رو یکی از درایوهام نصب کردم.

[Saman.S]

به جای این که مودم رو نصب کنید, این دستور ها رو اجرا کنید و خروجیشون رو بذارید.

کد: [انتخاب]

sudo /etc/init.d/sl-modem-daemon start
sudo slmodemd /dev/slamr0

[g.mehr]

[

کد: [انتخاب]

sudo /etc/init.d start
sudo: /etc/init.d: command not found

کد: [انتخاب]

sudo slmodemd /dev/slamr0
error: mdm setup: cannot open dev `/dev/slamr0': Device or resource busy
error: cannot setup device `/dev/sla
 

[Saman.S]

آخ ببخشید دستور اول رو اشتباه نوشته بودم. درستش کردم.
ولی خروجی دستور دوم نشون می ده که مودم نصب شده و قابل استفادست. قبل از نصب دوباره ی مودم این کارو کردید؟
در ضمن تو خروجی wvdialconf نوشته بود:

کد: [انتخاب]

ttySL0<Info>: Permission deniedیعنی این که برنامه اجازه ی دسترسی به فایل dev/ttySL0/(که همون دیوایس مودمه) رو نداره.
به جای wvdialconf از sudo wvdialconf استفاده کنید ببینید چی می شه.

[Allahparast]

سلام منم ubuntu 8.10 نبصیدم ولی network رو پیدا نکردم کلا دارم قاطی می کنم هرکی هم بتونه مشکلم رو حل کنه پول خوبی بهش میدم یه میل بهم بزنه aallahparast@gamail.com
مشکلم هم نصب مودم هست 

[Saman.S]

سلام منم ubuntu 8.10 نبصیدم ولی network رو پیدا نکردم کلا دارم قاطی می کنم هرکی هم بتونه مشکلم رو حل کنه پول خوبی بهش میدم یه میل بهم بزنه aallahparast@gamail.com
مشکلم هم نصب مودم هست 

خوش اومدید
اول این که ظاهرا ۸.۱۰ به صورت پیشفرض Network نداره باید نصبش کنید.
دوم این که مودم نصب کردن که پول گرفتن نمی خواد
سوم این که بگید خودتون تا چه حد پیش رفتید؟ طبق راهنمای زیر پیش برید.

کد: [انتخاب]

http://wiki.ubuntu-ir.org/DialupModemHowto

[ddavod]

اقا اولین مشکل من اینه که بسته درایور مودم من تا کلیک میکنم نصب میشه در حالی تو ورژنهای قبلی اوبونتو 2 دقیقهای برای نصب دراور وقت میزاشت من که احساس میکنم درایورم نصب نمیشه

[Dallas1387]

سلام لطف کنید منو راهنمایی کنید من دستور اسکن مودم رو اجرا کردم اون دوتا فایل رو هم ایجاد شد من می زارم اینجا لطف کنید بفرمایید مودم از چه نوعی هست و برای نصب هم کمکم کنید ممنون می شم

کد: [انتخاب]

If you want help from the email group Discuss@linmodems.org, PLEASE join the List
at http://www.linmodems.org . Otherwise your messages will be delayed until the evening,
waiting for someone to verify it is not junk mail, before forwarding through the List server.
   
The files in this Modem/ folder have the following roles:

ModemData.txt - Diagnostics and accumulated information cogent to your modem and host system.
     This is the ONLY file which should be sent to the List  DISCUSS@LINMODEMS.ORG ,
     if further help is needed. Send your email and attachments as plain text as
     other formats are rejected by the List Server, to avoid virus transmission.
     Always send the ENTIRE ModemData.txt,  as It includes subtle diagnostic ouputs needed
     to best guide you. Please in the covering email mention your Country, to enable Country
     specific advice.
     Always use the most recent update of scanModem accessed ONLY at
   http://linmodems.technion.ac.il/packages/scanModem.gz
     to produce ModemData.txt
     URLs to cogent advice are regularly updated, so your problem may be solved therein.
     Please Do NOT send  Do NOT send other files in this folder Modem/

Several informative files without diagnostics are in the DOCs subfolder.
A file(s) specific to your modem chipset will be written, such as:
  Smartlink.txt, Conexant.txt, Intel.txt , etc

YourModem.txt - Guidance about operating your particular System, for your benefit
     It should NOT be sent to Discuss@linmodems.org

Rational.txt - Motivations of this scanModem package. 

DriverCompiling.txt -  Explains the roles of additional files which may have to be installed
   to support compiling of modem drivers, and the steps to take.   

SoftModem.txt - Information and instructions about "soft modems".
     For these modems, additional steps may be necessary for choice of supporting software.
     The primary PCI ID is that of the host audio or modem controller, which can support diverse Subsystems. It is the chipset of the Subsystem which determines the software needed.

ModemTesting.txt SHOULD be read, but after drivers have been installed.

InfoGeneral.txt has general information about the status of winmodem support under Linux,
    Do read it if ModemData.txt  reports that your current modem is not supported under Linux.

Unsubscribe.txt - Howto terminate email tranmissions from the List.

If you are Linux newcomer, please do locate your local Linux group through:
    http://www.linux.org/groups/index.html  .  If you are not comfortable with English,
    a local Linux user can often be of substantial assistance in getting you on to the Internet.
 
و این هم مودم دیتا

کد: [انتخاب]

Only plain text email is forwarded by the  Discuss@Linmodems.org List Server,
 as HTML can contain viruses. Use as the email Subject Line:
           YourName, YourCountry  kernel 2.6.28-11-generic
 With this Subject Line cogent experts will be alerted, and useful case names left in the Archive.
 YourCountry will enable Country specific guidance. Linux experts in YourCountry
 can be found through: http://www.linux.org/groups/index.html.
They will know your Country's modem code, which may be essential for dialup service.
Responses from Discuss@Linmodems.org are sometimes blocked by an Internet Provider mail filters.
 So in a day, also check the Archived responses at http://www.linmodems.org
--------------------------  System information ----------------------------
CPU=i686, 
Linux version 2.6.28-11-generic (buildd@palmer) (gcc version 4.3.3 (Ubuntu 4.3.3-5ubuntu4) ) #42-Ubuntu SMP Fri Apr 17 01:57:59 UTC 2009
 scanModem update of:  2009_05_12

 There are no blacklisted modem drivers in /etc/modprobe*  files
 Potentially useful modem drivers now loaded are:
               

Attached USB devices are:
 ID 03f0:0c17 Hewlett-Packard LaserJet 1010
 ID 0a5c:2021 Broadcom Corp.
If a cellphone is not detected, see http://ubuntuforums.org/archive/index.php/t-878554.html

If a USB modem or cellphone is attached and was not detected, please
provide available information in your request to discuss@linmodems.org

For candidate card in slot 00:09.0, firmware information and bootup diagnostics are:
 PCI slot PCI ID SubsystemID Name
 ---------- --------- --------- --------------
 00:09.0 14f1:2f00 14f1:2004 Communication controller: Conexant Systems, Inc. HSF 56k HSFi Modem

 Modem interrupt assignment and sharing:
 --- Bootup diagnostics for card in PCI slot 00:09.0 ----
[    0.564348] pci 0000:00:09.0: reg 10 32bit mmio: [0xf7ff0000-0xf7ffffff]
[    0.564358] pci 0000:00:09.0: reg 14 io port: [0xec00-0xec07]
[    0.564399] pci 0000:00:09.0: PME# supported from D3hot D3cold
[    0.564404] pci 0000:00:09.0: PME# disabled

 The PCI slot 00:09.0 of the modem card may be disabled early in
 a bootup process,  but then enabled later. If modem drivers load
 but the  modem is not responsive, read DOCs/Bootup.txt about possible fixes.
 Send dmesg.txt along with ModemData.txt to discuss@linmodems.org
 if help is needed.
 

=== Finished firmware and bootup diagnostics, next deducing cogent software. ===

Predictive  diagnostics for card in bus 00:09.0:
Modem chipset  detected on
NAME="Communication controller: Conexant Systems, Inc. HSF 56k HSFi Modem "
CLASS=0780
PCIDEV=14f1:2f00
SUBSYS=14f1:2004
IRQ=11
IDENT=hsfmodem
Driver=hsfmodem-drivers

 For candidate modem in:  00:09.0
   0780 Communication controller: Conexant Systems, Inc. HSF 56k HSFi Modem
      Primary device ID:  14f1:2f00
 Support type needed or chipset: hsfmodem
 


For owners of a Dell PCs with Conexant HSF modems, a driver source package with full speed enabled is available, but requires driver compiling. Read DOCs/Conexant.txt


Start at http://www.linuxant.com/drivers/hsf/downloads-license.php to find the
hsfmodem package matching your System. For several Linux distros, there are
precompiled drivers matched to specific kernels. These have within the FileName,
your KernelVersion: 2.6.28_11_generic
They can be found through http://www.linuxant.com/drivers/hsf/full/downloads.php
A more precise location may be given a few paragraphs below.
If an EXACT Match with your your KernelVersion is not found, one of the
"Generic packages with source" near the bottom of the page must be used.
Downloaded packages must be moved into the Linux partition (home folder is OK)
and unzipped with:
unzip hsf*.zip
The installation command for a .deb suffic packages is, with root/adm permission:
  sudo dpkg -i hsf*.deb
while for .rpm suffix it is, with:
  rpm -i hsf*.rpm
 From  http://www.linuxant.com/drivers/hsf/full/downloads-ubuntu-x86.php
 download hsfmodem-7.80.02.02full_k2.6.28_11_generic_ubuntu_i386.deb.zip
 Under Linux unpack with:
 $ unzip hsfmodem*.zip
 Then install with:
 $ sudo dpkg -i hsfmodem*.deb
 Subsequently, the modem should be found with
 $ sudo wvdialconf /etc/wvdial.conf
 Edit in your personal information with:
 $ sudo gedit /etc/wvdial.conf
 and try dialing out with:
 $ sudo wvdial.
 See DOCs/Testing.txt  for details.
 
 Read DOCs/Conexant.txt

Writing DOCs/Conexant.txt


 Completed candidate modem analyses.

 The base of the UDEV device file system is: /dev/.udev

 Versions adequately match for the compiler installed: 4.3.3
             and the compiler used in kernel assembly: 4.3.3

 The patch utility is needed and is needed for compiling ALSA drivers, and possibly others.

 
 Minimal compiling resources appear complete:
   make utility - /usr/bin/make
   Compiler version 4.3
   linuc_headers base folder /lib/modules/2.6.28-11-generic/build

 However some compilations and executable functions may need additional files,
 in the FileNames.h (so called kernel "h"eaders) collection installed in  /usr/include/ .
 For martian_modem, additional required packages are needed. The also required headers of package libc6 are commonly installed by default.
 Compiling hsfmodem drivers does require linux-libc-dev and libc6-dev packages, for kernels 2.6.24 and later versions.
 In not included on your install CD, search for them at http://packages.ubuntu.com
 or comparable Repository for other Linux distros.
 When compiling ALSA drivers, the utility "patch" will also be needed.




If a driver compilation fails, with message including some lack of some FileName.h (stdio.h for example), then
Some additional kernel-header files need installation to /usr/include. The minimal additional packages are libc6-dev
and any of its dependents, under Ubuntu linux-libc-dev

If an alternate ethernet connection is available,
$  apt-get update
$  apt-get -s install linux-kernel-devel
will install needed packages.
For Debian/Ubuntu related distributions, run the following command to display the needed package list:

Otherwise packages have to be found through http://packages.ubuntu.com
Once downloaded and transferred into a Linux partition,
they can be installed alltogether with:
$ sudo dpkg -i *.deb

Checking settings of: /etc/ppp/options
asyncmap 0
noauth
crtscts
lock
hide-password
modem
proxyarp
lcp-echo-interval 30
lcp-echo-failure 4
noipx

In case of a message like:
   Warning: Could not modify /etc/ppp/pap-secrets: Permission denied
see http://linmodems.technion.ac.il/bigarch/archive-sixth/msg04656.html

Read Modem/DOCs/YourSystem.txt concerning other COMM channels: eth0
Which can interfere with Browser naviagation.

 Don't worry about the following, it is for experts should trouble shooting be necessary.
==========================================================

 Checking for modem support lines:
 --------------------------------------
     /device/modem symbolic link:   
slmodemd created symbolic link /dev/ttySL0: 
     Within /etc/udev/ files:

     Within /etc/modprobe.conf files:
/etc/modprobe.d/alsa-base.conf:options snd-atiixp-modem index=-2
/etc/modprobe.d/alsa-base.conf:options snd-via82xx-modem index=-2
/etc/modprobe.d/blacklist-modem.conf:# Uncomment these entries in order to blacklist unwanted modem drivers
/etc/modprobe.d/blacklist-modem.conf:# blacklist snd-atiixp-modem
/etc/modprobe.d/blacklist-modem.conf:# blacklist snd-via82xx-modem
     Within any ancient /etc/devfs files:

     Within ancient kernel 2.4.n /etc/module.conf files:

--------- end modem support lines --------

ممنون می شم کمک کنید چون واقعا به اینترنت توی محیط لینوکس نیاز دارم من از اوبونتو 9.04 استفاده می کنم

[Saman.S]

این فایل رو دانلود و نصب کنید.

کد: [انتخاب]

http://www.linuxant.com/drivers/hsf/full/archive/hsfmodem-7.80.02.04full/hsfmodem_7.80.02.04full_k2.6.28_11_generic_ubuntu_i386.deb.zipو بعد در محیط ترمینال این دستور را وارد کنید.

کد: [انتخاب]

sudo hsfconfigبعد برای ساختن کانکشن طبق این راهنما عمل کنید.

کد: [انتخاب]

http://wiki.ubuntu-ir.org/DialupModemHowto/SetUpDialer?highlight=%28Dialupmodemhowto%29

[Dallas1387]

سلام
من بعد از اسکن مودم خروجی رو گذاشتم ( پست 40 ) و اون فایلی که سامان عزیز دادند رو دانلود کردم اما در هنگام نصب ارور می ده و نصب نمی شه باید چیکار کنم ؟؟

[Saman.S]

سلام
من بعد از اسکن مودم خروجی رو گذاشتم ( پست 40 ) و اون فایلی که سامان عزیز دادند رو دانلود کردم اما در هنگام نصب ارور می ده و نصب نمی شه باید چیکار کنم ؟؟

چه اروری داد؟

[AliRezaiMi]

سلام آقا من درايور مودمم رو نصب كردم (زولتريكس hcf)اما نميتونم on بشم
با kppp هر كاري ميكنم نميشه و بعضي وقتها ارورر زير ميده

لطفا يه راهي براي on شدن با اوبونتو به dialup به من بديد
ممنون